Home › Audio / Visual / Telematics › NAVIGATION / MULTI INFO DISPLAY › NAVIGATION SYSTEM
RM27L0U _56 Audio / Visual / Telematics _049330 NAVIGATION / MULTI INFO DISPLAY _0235785 NAVIGATION SYSTEM J

NAVIGATION / MULTI INFO DISPLAY  NAVIGATION SYSTEM  Vehicle Speed Signal Circuit between Navigation Receiver Assembly and Combination Meter  


DESCRIPTION

The navigation receiver assembly receives a vehicle speed signal from the combination meter assembly to control the ASL function.

HINT:
·

A voltage of 12 V or 5 V is output from each ECU and then input to the combination meter assembly. The signal is changed to a pulse signal at the transistor in the combination meter assembly. Each ECU controls the respective systems based on the pulse signal.

·

If a short occurs in any of the ECUs or in the wire harness connected to an ECU, all systems in the diagram below will not operate normally.



WIRING DIAGRAM

E282587E03
0.671,1.721 1.008,1.884 0.336,0.163 10 H37 0.671,1.889 2.556,2.087 1.885,0.198 10 Combination Meter Assembly 4.86,1.721 5.308,1.884 0.448,0.163 10 I53 4.86,1.889 7.016,2.087 2.156,0.198 10 Navigation Receiver Assembly 4.944,0.905 5.142,1.068 0.198,0.163 10 17 2.079,0.891 2.517,1.054 0.438,0.163 10 35 1.757,1.014 1.989,1.190 0.232,0.177 10 +S 5.224,1.014 5.637,1.190 0.413,0.177 10 SPD

PROCEDURE

1.CHECK COMBINATION METER ASSEMBLY (OUTPUT WAVEFORM)
a.
U154178E02
1.26,1.333 1.094,1.854 true 1.667,0.229 2,0.417 0.333,0.188 10 false H37 0.958,1.865 1.292,2.052 0.333,0.188 10 false +S 2.969,3.604 3.313,3.792 0.344,0.188 10 false GND 1.281,3.885 1.542,4.073 0.26,0.188 10 false (A) 0.031,0.052 0.365,0.24 0.333,0.188 10 false *a

Check the output waveform.

i.

Remove the combination meter assembly with the connector(s) still connected.


ii.

Connect an oscilloscope to terminal H37-35 (+S) and body ground.


iii.

Turn the ignition switch to ON.


iv.

Turn a wheel slowly.


v.

Check the signal waveform according to the condition(s) in the table below.

Item Condition
Measurement terminal H37-35 (+S) - Body ground
Tool setting 5 V/DIV., 20 ms./DIV.
Vehicle condition Wheel being rotated

OK:

The waveform is similar to that shown in the illustration.


HINT:

When the system is functioning normally, one wheel revolution generates 4 pulses. As the vehicle speed increases, the width indicated by (A) in the illustration narrows.


Text in Illustration
*a Component with harness connected
(Combination Meter Assembly)




OK

2.CHECK HARNESS AND CONNECTOR (NAVIGATION RECEIVER ASSEMBLY - COMBINATION METER ASSEMBLY)

NG

2.CHECK HARNESS AND CONNECTOR (NAVIGATION RECEIVER ASSEMBLY - COMBINATION METER ASSEMBLY)
a.

Disconnect the I53 navigation receiver assembly connector.


b.

Disconnect the H37 combination meter assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I53-17 (SPD) - H37-35 (+S) Always Below 1 Ω
I53-17 (SPD) - Body ground Always 10 kΩ or higher




OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR