Home › Audio / Visual / Telematics › NAVIGATION / MULTI INFO DISPLAY › NAVIGATION SYSTEM
RM27L0U _56 Audio / Visual / Telematics _049330 NAVIGATION / MULTI INFO DISPLAY _0235785 NAVIGATION SYSTEM J

NAVIGATION / MULTI INFO DISPLAY  NAVIGATION SYSTEM  Navigation Receiver Assembly Power Source Circuit  


DESCRIPTION

This circuit provides power to the navigation receiver assembly.

WIRING DIAGRAM

E282601E05
5.469,2.177 6.823,2.531 1.354,0.354 10 false Navigation Receiver Assembly 5.719,0.354 6.208,0.521 0.49,0.167 10 false +B1 5.719,1.75 6.333,1.917 0.615,0.167 10 false GND1 5.719,1.313 6.271,1.479 0.552,0.167 10 false ACC1 5.719,0.833 6.104,1 0.385,0.167 10 false IG 5.396,1.323 5.708,1.49 0.313,0.167 10 false I26 5.396,0.375 5.99,0.542 0.594,0.167 10 false I26 5.406,0.823 6,0.99 0.594,0.167 10 false I53 5.396,1.75 5.969,1.917 0.573,0.167 10 false I26 5.458,0.188 5.594,0.354 0.135,0.167 10 false 4 5.458,1.573 5.594,1.74 0.135,0.167 10 false 7 5.458,0.646 5.573,0.813 0.115,0.167 10 false 1 5.458,1.125 5.573,1.292 0.115,0.167 10 false 3 3.167,1.469 3.521,1.646 0.354,0.177 10 false ACC 2.938,0.958 4.365,1.135 1.427,0.177 10 false ECU-IG NO. 1 3.01,0.51 3.979,0.688 0.969,0.177 10 false RAD NO. 1 0.938,0.365 1.771,0.542 0.833,0.177 10 false from Battery 0.854,0.781 1.865,1.135 1.01,0.354 10 false from IG NO. 1 Relay 0.76,1.313 1.844,1.49 1.083,0.177 10 false from ACC Relay

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (NAVIGATION RECEIVER ASSEMBLY - BATTERY AND BODY GROUND)
a.
U154180E01
0.134,0.054 0.307,0.211 0.173,0.158 10 *a 2.528,1.057 2.908,1.215 0.380,0.158 10 +B1 0.814,1.458 1.346,1.616 0.532,0.158 10 GND1 0.393,0.757 0.781,0.914 0.389,0.158 10 I26 2.27,0.423 2.746,0.581 0.476,0.158 10 ACC1 2.129,0.843 2.481,1.066 false 1.953,0.771 2.239,0.523 false 1.615,1.051 1.122,1.4 false 0.576,2.607 0.965,2.765 0.389,0.158 10 IG 1.065,2.52 0.805,2.661 false 0.43,2.215 0.819,2.372 0.389,0.158 10 I53

Disconnect the navigation receiver assembly connectors.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I26-7 (GND1) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
I26-4 (+B1) - Body ground Always 11 to 14 V
I26-3 (ACC1) - Body ground Ignition switch ACC 11 to 14 V
I53-1 (IG) - Body ground Ignition switch ON 11 to 14 V



Text in Illustration
*a Front view of wire harness connector
(to Navigation Receiver Assembly)


OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR