Home › Power Source / Network › 3UR-FBE BATTERY / CHARGING › GENERATOR
RM27L0U _57 Power Source / Network _049333 3UR-FBE BATTERY / CHARGING _0235799 GENERATOR A

3UR-FBE BATTERY / CHARGING  GENERATOR  REASSEMBLY  


PROCEDURE

Hide 27330 1.INSTALL GENERATOR ROTOR ASSEMBLY

a.
A156420

Place the drive end frame on the pulley.


b.

Install the rotor to the drive end frame.


Hide 27360 2.INSTALL GENERATOR COIL ASSEMBLY (for 130 A, 150 A Type)

a.
A156421

Place the generator washer on the rotor.


b.
A156422E02
2.622,0.173 2.959,0.355 0.337,0.182 10 SST 1.679,0.64 2.335,0.256 2.335,0.256 2.57,0.256 false

Using a 22 mm socket wrench and a press, slowly press in the coil assembly.


c.
A156414

Install the 4 bolts.

Torque:
5.8 N*m (59 kgf*cm, 51 in.*lbf)


Hide 27360 3.INSTALL GENERATOR COIL ASSEMBLY (for 180 A Type)

a.
A156421

Place the generator washer on the rotor.


b.
A156422E02
2.622,0.173 2.959,0.355 0.337,0.182 10 SST 1.679,0.64 2.335,0.256 2.335,0.256 2.57,0.256 false

Using a 22 mm socket wrench and a press, slowly press in the coil assembly.


c.
A156414

Install the 4 bolts.

Torque:
7.5 N*m (76 kgf*cm, 66 in.*lbf)


Hide 27370 4.INSTALL GENERATOR BRUSH HOLDER ASSEMBLY

a.
A163049

While pushing the 2 brushes toward the inside of the brush holder, insert a pin (diameter: 1.0 mm (0.0394 in.)) into the brush holder hole.


b.
A156423E03
2.88,0.189 3.172,0.377 0.292,0.188 10 Pin 1.791,0.863 2.626,0.275 2.626,0.275 2.816,0.275 false

Install the generator brush holder with the 2 screws.

Torque:
1.8 N*m (18 kgf*cm, 16 in.*lbf)


c.

Pull out the pin from the generator brush holder.


Hide 27039 5.INSTALL GENERATOR REAR END COVER

a.
A156408

Install the terminal insulator to the generator rectifier end frame.

NOTICE:

Pay attention to the mounting orientation of the terminal insulator.



b.
A156407

Install the end cover with the 3 nuts.

Torque:
4.6 N*m (47 kgf*cm, 41 in.*lbf)


Hide 27411 6.INSTALL GENERATOR PULLEY

A187035E09
3.073,1.229 3.073,0.573 false 2.427,1.521 2.427,1.365 2.427,1.365 2.833,0.719 false 0.927,1.333 1.219,1.563 0.292,0.229 10 true Turn 1.667,1.854 1.979,2 0.313,0.146 10 false Hold 2.125,1.542 2.719,1.719 0.594,0.177 10 false SST 1-B 2.76,1.25 3.313,1.396 0.552,0.146 10 false SST 1-A

SST
09820-63011  (09820-06010, 09820-06021)

HINT:
SST 1-A and B 09820-06010
SST 2 09820-06021


a.

Clamp the generator housing stay in a vise.


b.

Install the pulley onto the rotor shaft by tightening the pulley nut by hand.


c.

Hold SST 1-A with a torque wrench, and tighten SST 1-B clockwise to the specified torque.

Torque:
39 N*m (398 kgf*cm, 29 ft.*lbf)

NOTICE:

Check that SST is secured to the rotor shaft.



d.
A187036E08
2.563,0.427 2.688,0.427 2.688,0.427 2.792,0.885 false 2.031,0.333 2.469,0.552 0.438,0.219 10 false SST 2 2.375,1.354 2.76,1.552 0.385,0.198 10 true Insert

Insert SST 2, and attach the pulley nut to SST 2.


e.
A187039E08
0.865,1.313 1.177,1.313 1.177,1.313 1.927,1.094 false 2.896,0.74 3.198,0.938 0.302,0.198 10 false Turn 1.698,1.771 1.979,1.958 0.281,0.188 10 true Hold 0.208,1.25 0.875,1.563 0.667,0.313 10 false Adjustable wrench

Tighten the pulley nut by turning SST 1-A in the direction shown in the illustration.

Torque:
133 N*m (1351 kgf*cm, 98 ft.*lbf)

HINT:

Hold the adjustable wrench against the vise and tighten the nut securely.



f.

Remove the generator from SST 2.


g.
A187038E10
3.094,1.177 3.021,0.615 false 2.583,1.531 2.833,0.75 false 1.26,1.438 1.552,1.688 0.292,0.25 10 true Turn 1.917,1.656 2.24,1.865 0.323,0.208 10 true Hold 2.281,1.552 2.865,1.75 0.583,0.198 10 true SST 1-B 2.75,1.198 3.302,1.354 0.552,0.156 10 false SST 1-A

Turn SST 1-B, and remove SST 1-A and B.


h.

Turn the pulley and check that the pulley moves smoothly.