Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM
RM27L0U _57 Power Source / Network _049335 NETWORKING _0235802 CAN COMMUNICATION SYSTEM U

NETWORKING  CAN COMMUNICATION SYSTEM  TERMINALS OF ECU  


HINT:

Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.


DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL


a.

Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the CAN main wire and the CAN branch wire.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.


NOTICE:
·

Before measuring the resistance, leave the vehicle for at least 1 minute and do not operate the ignition switch, any switches or any doors. If doors need to be opened in order to check connectors, open the doors and leave them open.

·

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).

·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).





JUNCTION CONNECTOR


a.

NO. 1 JUNCTION CONNECTOR

U153680E01
2.329,1.524 2.684,1.663 0.355,0.140 10 H119 4.575,0.94 5.127,1.080 0.552,0.140 10 CANH*b 4.521,0.73 5.073,0.869 0.552,0.140 10 CANH*c 4.449,0.524 5.001,0.664 0.552,0.140 10 CANH*d 4.297,0.284 4.849,0.423 0.552,0.140 10 CANH*e 4.573,1.176 5.125,1.315 0.552,0.140 10 CANH*a 2.214,0.945 2.766,1.084 0.552,0.140 10 CANH*h 2.259,0.688 2.810,0.827 0.552,0.140 10 CANH*g 2.406,0.447 2.958,0.587 0.552,0.140 10 CANH*f 3.212,1.466 2.903,1.012 2.903,1.012 2.773,1.012 false 3.212,1.727 3,2.085 3,2.085 2.87,2.085 false 3.478,1.466 2.951,0.744 2.951,0.744 2.82,0.744 false 3.607,1.466 3.129,0.514 3.129,0.514 2.97,0.514 false 3.478,1.727 3.157,2.323 3.157,2.323 3.027,2.323 false 3.607,1.727 3.276,2.5 3.276,2.5 3.118,2.5 false 4.552,1.229 4.428,1.229 4.428,1.229 4.225,1.466 false 4.101,1.466 4.41,1.012 4.41,1.012 4.54,1.012 false 3.973,1.466 4.335,0.795 4.335,0.795 4.494,0.795 false 4.515,1.918 4.391,1.918 4.391,1.918 4.225,1.727 false 4.101,1.727 4.313,2.085 4.313,2.085 4.444,2.085 false 3.973,1.727 4.18,2.264 4.18,2.264 4.313,2.264 false 3.835,1.466 4.306,0.58 4.306,0.58 4.437,0.58 false 3.706,1.466 4.128,0.351 4.128,0.351 4.287,0.351 false 3.835,1.727 4.032,2.447 4.032,2.447 4.163,2.447 false 3.706,1.727 3.913,2.623 3.913,2.623 4.072,2.623 false 4.538,1.857 5.090,1.997 0.552,0.140 10 CANL*a 4.468,2.023 5.019,2.163 0.552,0.140 10 CANL*b 4.337,2.207 4.889,2.346 0.552,0.140 10 CANL*c 4.174,2.384 4.725,2.524 0.552,0.140 10 CANL*d 4.087,2.561 4.639,2.701 0.552,0.140 10 CANL*e 2.324,2.015 2.876,2.155 0.552,0.140 10 CANL*h 2.485,2.26 3.037,2.400 0.552,0.140 10 CANL*g 2.614,2.437 3.165,2.577 0.552,0.140 10 CANL*f

Text in Illustration
*a for Center Airbag Sensor Assembly *b
·

for No. 4 Junction Connector (w/ Air Suspension System)

·

for Combination Meter Assembly (V1 Bus) (w/o Air Suspension System)


*c for DLC3 *d for Steering Angle Sensor
*e for No. 2 Junction Connector *f for Main Body ECU (Cowl Side Junction Block LH) (V1 Bus)
*g for Power Steering ECU Assembly *h for Brake Actuator Assembly (Skid Control ECU)

No. 1 Junction Connector Wiring Color Connect to
H119-1 (CANH) BR Center airbag sensor assembly
H119-12 (CANL) W
H119-2 (CANH) SB
·

No. 4 junction connector*1

·

Combination meter assembly (V1 bus)*2


H119-13 (CANL) W
H119-3 (CANH) V DLC3
H119-14 (CANL) W
H119-4 (CANH) G Steering angle sensor
H119-15 (CANL) W
H119-5 (CANH) R No. 2 junction connector
H119-16 (CANL) W
H119-6 (CANH) L Main body ECU (cowl side junction block LH) (V1 bus)
H119-17 (CANL) W
H119-7 (CANH) GR Power steering ECU assembly
H119-18 (CANL) W
H119-9 (CANH) B Brake actuator assembly (skid control ECU)
H119-20 (CANL) W

*1: w/ Air Suspension System

*2: w/o Air Suspension System



b.

NO. 2 JUNCTION CONNECTOR

U153683E02
4.604,1.229 4.49,1.229 4.49,1.229 4.198,1.479 false 4.073,1.469 4.469,1.01 4.469,1.01 4.594,1.01 false 3.958,1.469 4.396,0.792 4.396,0.792 4.552,0.792 false 4.573,1.917 4.448,1.917 4.448,1.917 4.24,1.729 false 4.104,1.729 4.365,2.083 4.365,2.083 4.5,2.083 false 3.948,1.729 4.24,2.26 4.24,2.26 4.365,2.26 false 3.823,1.479 4.365,0.583 4.365,0.583 4.49,0.583 false 3.833,1.729 4.083,2.448 4.083,2.448 4.219,2.448 false 3.594,1.469 3.208,0.677 3.208,0.677 3.104,0.677 false 3.573,1.729 3.427,2.219 3.427,2.219 3.271,2.219 false 3.698,1.469 4.188,0.354 4.188,0.354 4.344,0.354 false 3.708,1.719 3.969,2.625 3.969,2.625 4.125,2.625 false 2.333,1.5 2.708,1.688 0.375,0.188 10 false H115 4.635,0.938 5.188,1.073 0.552,0.135 10 false CANH*b 4.573,0.729 5.125,0.865 0.552,0.135 10 false CANH*c 4.5,0.521 5.052,0.656 0.552,0.135 10 false CANH*d 4.354,0.281 4.906,0.417 0.552,0.135 10 false CANH*e 4.146,2.563 4.698,2.698 0.552,0.135 10 false CANL*e 2.573,0.615 3.125,0.75 0.552,0.135 10 false CANH*f 4.625,1.177 5.177,1.313 0.552,0.135 10 false CANH*a 4.594,1.854 5.146,1.99 0.552,0.135 10 false CANL*a 4.521,2.021 5.073,2.156 0.552,0.135 10 false CANL*b 4.396,2.208 4.948,2.344 0.552,0.135 10 false CANL*c 4.229,2.385 4.781,2.521 0.552,0.135 10 false CANL*d 2.76,2.156 3.344,2.354 0.583,0.198 10 false CANL*f

Text in Illustration
*a for Air Conditioning Amplifier Assembly *b for 4 Wheel Drive Control ECU (4WD Control ECU) (for 4WD)
*c for ECM *d for No. 1 Junction Connector
*e for Bus Buffer ECU (w/ Bus Buffer ECU) *f for Network Gateway ECU (V1 bus) (w/ Network Gateway ECU)

No. 2 Junction Connector Wiring Color Connect to
H115-1 (CANH) B Air conditioning amplifier assembly
H115-12 (CANL) W
H115-2 (CANH) BE 4 wheel drive control ECU (4WD control ECU)*1
H115-13 (CANL) W
H115-3 (CANH) GR ECM
H115-14 (CANL) W
H115-4 (CANH) R No. 1 junction connector
H115-15 (CANL) W
H115-5 (CANH) P Bus buffer ECU*2
H115-16 (CANL) W
H115-6 (CANH) SB Network gateway ECU (V1 bus)*3
H115-17 (CANL) W

*1: for 4WD

*2: w/ Bus Buffer ECU

*3: w/ Network Gateway ECU



c.

NO. 3 JUNCTION CONNECTOR

U153684E01
3.422,0.332 3.774,0.472 0.352,0.140 10 H116 4.449,0.524 5.001,0.664 0.552,0.140 10 CANH*d 4.297,0.284 4.849,0.423 0.552,0.140 10 CANH*e 2.639,1.229 2.763,1.229 2.763,1.229 2.966,1.466 false 3.09,1.466 2.782,1.012 2.782,1.012 2.651,1.012 false 3.219,1.466 2.857,0.795 2.857,0.795 2.698,0.795 false 2.677,1.918 2.801,1.918 2.801,1.918 2.966,1.727 false 3.09,1.727 2.879,2.085 2.879,2.085 2.748,2.085 false 3.219,1.727 3.012,2.264 3.012,2.264 2.879,2.264 false 4.552,1.229 4.428,1.229 4.428,1.229 4.225,1.466 false 4.101,1.466 4.41,1.012 4.41,1.012 4.54,1.012 false 3.973,1.466 4.335,0.795 4.335,0.795 4.494,0.795 false 4.515,1.918 4.391,1.918 4.391,1.918 4.225,1.727 false 4.101,1.727 4.313,2.085 4.313,2.085 4.444,2.085 false 3.973,1.727 4.18,2.264 4.18,2.264 4.313,2.264 false 3.835,1.466 4.306,0.58 4.306,0.58 4.437,0.58 false 3.706,1.466 4.128,0.351 4.128,0.351 4.287,0.351 false 3.835,1.727 4.032,2.447 4.032,2.447 4.163,2.447 false 3.706,1.727 3.913,2.623 3.913,2.623 4.072,2.623 false 2.091,0.94 2.642,1.080 0.552,0.140 10 CANH*g 2.135,0.73 2.687,0.869 0.552,0.140 10 CANH*f 2.088,1.176 2.640,1.315 0.552,0.140 10 CANH*h 2.144,1.857 2.696,1.997 0.552,0.140 10 CANL*h 2.2,2.023 2.752,2.163 0.552,0.140 10 CANL*g 2.346,2.207 2.898,2.346 0.552,0.140 10 CANL*f 4.575,0.94 5.127,1.080 0.552,0.140 10 CANH*b 4.521,0.73 5.073,0.869 0.552,0.140 10 CANH*c 4.573,1.176 5.125,1.315 0.552,0.140 10 CANH*a 4.538,1.857 5.090,1.997 0.552,0.140 10 CANL*a 4.468,2.023 5.019,2.163 0.552,0.140 10 CANL*b 4.337,2.207 4.889,2.346 0.552,0.140 10 CANL*c 4.174,2.384 4.725,2.524 0.552,0.140 10 CANL*d 4.087,2.561 4.639,2.701 0.552,0.140 10 CANL*e

Text in Illustration
*a for Combination Meter Assembly (MS Bus) *b for Multiplex Tilt and Telescopic ECU (w/ Seat Memory)
*c for Front Power Seat Switch LH (Power Seat Control ECU) (w/ Seat Memory) *d
·

for No. 4 Junction Connector (w/ Power Back Door System)

·

for Main Body ECU (Cowl Side Junction Block LH) (MS Bus) (w/o Power Back Door System)


*e for Outer Mirror Control ECU Assembly (w/ Seat Memory) *f for No. 5 Junction Connector (w/ Network Gateway ECU)
*g for Network Gateway ECU (V2 Bus) (w/ Network Gateway ECU) *h for Distance Control ECU Assembly (w/ Dynamic Laser Cruise Control System)

No. 3 Junction Connector Wiring Color Connect to
H116-1 (CANH) Y Combination meter assembly (MS bus)
H116-12 (CANL) W
H116-2 (CANH) BE Multiplex tilt and telescopic ECU*1
H116-13 (CANL) W
H116-3 (CANH) GR Front power seat switch LH (power seat control ECU)*1
H116-14 (CANL) W
H116-4 (CANH) B
·

No. 4 junction connector*2

·

Main body ECU (cowl side junction block LH) (MS bus)*3


H116-15 (CANL) W
H116-5 (CANH) LG Outer mirror control ECU assembly*1
H116-16 (CANL) W
H116-9 (CANH) B No. 5 junction connector*4
H116-20 (CANL) W
H116-10 (CANH) L Network gateway ECU (V2 bus)*4
H116-21 (CANL) W
H116-11 (CANH) BE Distance control ECU assembly*5
H116-22 (CANL) W

*1: w/ Seat Memory

*2: w/ Power Back Door System

*3: w/o Power Back Door System

*4: w/ Network Gateway ECU

*5: w/ Dynamic Laser Cruise Control System



d.

NO. 4 JUNCTION CONNECTOR (FRONT OF THE VEHICLE) (w/ Power Back Door System or w/ Air Suspension System)

U153740E01
2.942,2.937 3.066,2.937 3.066,2.937 3.253,2.785 false 3.41,2.785 3.082,3.47 3.082,3.47 2.994,3.47 false 2.942,2.454 3.066,2.454 3.066,2.454 3.253,2.606 false 3.41,2.606 3.096,2.134 3.096,2.134 3.008,2.134 false 4.318,2.937 4.194,2.937 4.194,2.937 4.007,2.785 false 3.85,2.785 4.163,3.257 4.163,3.257 4.252,3.257 false 4.318,2.454 4.194,2.454 4.194,2.454 4.007,2.606 false 3.85,2.606 4.163,2.134 4.163,2.134 4.252,2.134 false 4.332,2.391 4.890,2.528 0.559,0.137 10 CANH*a 4.268,2.069 4.827,2.206 0.559,0.137 10 CANH*b 4.268,3.196 4.827,3.334 0.559,0.137 10 CANL*b 4.332,2.879 4.890,3.016 0.559,0.137 10 CANL*a 2.389,2.391 2.947,2.528 0.559,0.137 10 CANH*d 2.454,2.069 3.013,2.206 0.559,0.137 10 CANH*c 2.44,3.409 2.999,3.546 0.559,0.137 10 CANL*c 2.4,2.879 2.959,3.016 0.559,0.137 10 CANL*d 3.486,3.388 3.767,3.525 0.281,0.137 10 O41

Text in Illustration
*a for Combination Meter Assembly (V1 Bus) *b for No. 1 Junction Connector
*c for Main Body ECU (Cowl Side Junction Block LH) (MS Bus) *d for No. 3 Junction Connector (MS Bus)

No. 4 Junction Connector Wiring Color Connect to
O41-1 (CANH) SB Combination meter assembly (V1 bus)
O41-7 (CANL) W
O41-2 (CANH) L No. 1 junction connector
O41-8 (CANL) W
O41-5 (CANH) B Main body ECU (cowl side junction block LH) (MS bus)
O41-11 (CANL) W
O41-6 (CANH) P No. 3 junction connector (MS bus)
O41-12 (CANL) W


e.

NO. 4 JUNCTION CONNECTOR (REAR OF THE VEHICLE) (w/ Power Back Door System or w/ Air Suspension System)

U153741E01
2.942,2.916 3.066,2.916 3.066,2.916 3.253,2.764 false 2.942,2.433 3.066,2.433 3.066,2.433 3.253,2.585 false 4.318,2.916 4.194,2.916 4.194,2.916 4.007,2.764 false 4.318,2.433 4.194,2.433 4.194,2.433 4.007,2.585 false 4.332,2.37 4.890,2.507 0.559,0.137 10 CANH*a 4.332,2.858 4.890,2.995 0.559,0.137 10 CANL*a 2.389,2.37 2.947,2.507 0.559,0.137 10 CANH*b 2.4,2.858 2.959,2.995 0.559,0.137 10 CANL*b 3.486,3.367 3.767,3.504 0.281,0.137 10 O42

Text in Illustration
*a for Power Back Door Unit Assembly (Power Back Door ECU) (w/ Power Back Door System) *b for Suspension Control ECU (w/ Air Suspension System)

No. 4 Junction Connector Wiring Color Connect to
O42-1 (CANH) B Power back door unit assembly (power back door ECU)*1
O42-7 (CANL) W
O42-6 (CANH) B Suspension control ECU*2
O42-12 (CANL) W

*1: w/ Power Back Door System

*2: w/ Air Suspension System



f.

NO. 5 JUNCTION CONNECTOR (w/ Network Gateway ECU)

U153681E01
4.585,1.524 4.868,1.663 0.283,0.140 10 O47 2.109,0.961 2.661,1.101 0.552,0.140 10 CANH*b 2.108,1.182 2.660,1.321 0.552,0.140 10 CANH*c 2.156,0.741 2.708,0.881 0.552,0.140 10 CANH*a 2.646,1.243 2.77,1.243 2.77,1.243 2.973,1.48 false 3.097,1.48 2.789,1.026 2.789,1.026 2.658,1.026 false 3.225,1.48 2.863,0.809 2.863,0.809 2.704,0.809 false 2.683,1.918 2.807,1.918 2.807,1.918 2.973,1.727 false 3.097,1.727 2.885,2.085 2.885,2.085 2.755,2.085 false 3.225,1.727 3.019,2.264 3.019,2.264 2.885,2.264 false 2.349,2.2 2.900,2.339 0.552,0.140 10 CANL*a 2.212,2.023 2.764,2.163 0.552,0.140 10 CANL*b 2.144,1.846 2.696,1.985 0.552,0.140 10 CANL*c

Text in Illustration
*a for No. 3 Junction Connector (V2 Bus) *b for No. 6 Junction Connector
*c for Blind Spot Monitor Sensor LH (w/ Blind Spot Monitor Sensor) - -

No. 5 Junction Connector Wiring Color Connect to
O47-9 (CANH) B No. 3 junction connector (V2 bus)
O47-20 (CANL) W
O47-10 (CANH) G No. 6 junction connector
O47-21 (CANL) W
O47-11 (CANH) BE Blind spot monitor sensor LH*
O47-22 (CANL) W

*: w/ Blind Spot Monitor Sensor



g.

NO. 6 JUNCTION CONNECTOR (w/ Network Gateway ECU)

U153682E01
4.585,1.524 4.868,1.663 0.283,0.140 10 O48 2.109,0.961 2.661,1.101 0.552,0.140 10 CANH*b 2.108,1.182 2.660,1.321 0.552,0.140 10 CANH*c 2.156,0.741 2.708,0.881 0.552,0.140 10 CANH*a 2.646,1.243 2.77,1.243 2.77,1.243 2.973,1.48 false 3.097,1.48 2.789,1.026 2.789,1.026 2.658,1.026 false 3.225,1.48 2.863,0.809 2.863,0.809 2.704,0.809 false 2.683,1.918 2.807,1.918 2.807,1.918 2.973,1.727 false 3.097,1.727 2.885,2.085 2.885,2.085 2.755,2.085 false 3.225,1.727 3.019,2.264 3.019,2.264 2.885,2.264 false 2.349,2.2 2.900,2.339 0.552,0.140 10 CANL*a 2.212,2.023 2.764,2.163 0.552,0.140 10 CANL*b 2.144,1.846 2.696,1.985 0.552,0.140 10 CANL*c

Text in Illustration
*a for No. 5 Junction Connector *b for Blind Spot Monitor Sensor RH (w/ Blind Spot Monitor Sensor)
*c for No. 7 Junction Connector - -

No. 6 Junction Connector Wiring Color Connect to
O48-9 (CANH) G No. 5 junction connector
O48-20 (CANL) W
O48-10 (CANH) R Blind spot monitor sensor RH*
O48-21 (CANL) W
O48-11 (CANH) L No. 7 junction connector
O48-22 (CANL) W

*: w/ Blind Spot Monitor Sensor



h.
U153742E01
1.286,0.998 1.024,1.35 1.024,1.35 0.899,1.35 false 1.164,0.398 1.292,0.398 1.292,0.398 1.606,0.805 false 0.221,1.271 0.776,1.411 0.555,0.139 10 CANH*a 0.489,0.325 1.045,0.464 0.555,0.139 10 CANL*a 2.697,0.795 2.981,0.934 0.283,0.140 10 O49

NO. 7 JUNCTION CONNECTOR (w/ Network Gateway ECU)

Text in Illustration
*a No. 6 Junction Connector

No. 7 Junction Connector Wiring Color Connect to
O49-3 (CANH) L No. 6 junction connector
O49-2 (CANL) W



CHECK DLC3


U153664E02
1.948,0.917 1.656,0.417 1.656,0.417 1.531,0.417 false 2.323,0.917 2.625,0.417 2.625,0.417 2.75,0.417 false 1.927,1.49 1.677,1.917 1.677,1.917 1.552,1.917 false 2.292,1.469 2.552,1.896 2.552,1.896 2.677,1.896 false 2.802,0.344 3.271,0.531 0.469,0.188 10 false CANH 1.26,0.323 1.521,0.552 0.26,0.229 10 false CG 1.135,1.823 1.542,2.01 0.406,0.188 10 false CANL 0.271,1.125 0.552,1.354 0.281,0.229 10 false H19 2.76,1.813 3.073,1.969 0.313,0.156 10 false BAT

a.

Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the CAN main wire and the CAN branch wire.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.


NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).



b.

Measure the resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Switch Condition Specified Condition
H19-6 (CANH) - H19-14 (CANL) V - W Ignition switch off 54 to 69 Ω
H19-6 (CANH) - H19-4 (CG) V - W-B Ignition switch off 200 Ω or higher
H19-14 (CANL) - H19-4 (CG) W - W-B Ignition switch off 200 Ω or higher
H19-6 (CANH) - H19-16 (BAT) V - P Ignition switch off 6 kΩ or higher
H19-14 (CANL) - H19-16 (BAT) W - P Ignition switch off 6 kΩ or higher



CHECK BRAKE ACTUATOR ASSEMBLY (SKID CONTROL ECU)


U153722E02
5.125,1.302 5.646,1.76 5.646,1.76 5.76,1.76 false 2.01,1.323 1.677,2.208 1.677,2.208 1.563,2.208 false 4.104,1.26 3.75,2.25 3.75,2.25 3.635,2.25 false 4.292,1.271 4.646,2.26 4.646,2.26 4.76,2.26 false 3.198,2.177 3.698,2.385 0.5,0.208 10 false CANH 4.823,2.177 5.344,2.427 0.521,0.25 10 false CANL 5.802,1.698 6.333,1.927 0.531,0.229 10 false GND1 1.135,2.135 1.583,2.344 0.448,0.208 10 false +BM 1.167,1.375 1.479,1.583 0.313,0.208 10 false A19

a.

Disconnect the A19 brake actuator assembly (skid control ECU) connector.


b.

Measure the resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Switch Condition Specified Condition
A19-12 (CANH) - A19-13 (CANL) B - W Ignition switch off 54 to 69 Ω
A19-12 (CANH) - A19-16 (GND1) B - W-B Ignition switch off 200 Ω or higher
A19-13 (CANL) - A19-16 (GND1) W - W-B Ignition switch off 200 Ω or higher
A19-12 (CANH) - A19-1 (+BM) B - L Ignition switch off 6 kΩ or higher
A19-13 (CANL) - A19-1 (+BM) W - L Ignition switch off 6 kΩ or higher



CHECK MAIN BODY ECU (COWL SIDE JUNCTION BLOCK LH)


U153564E01
1.958,2.125 2.170,2.264 0.212,0.139 10 DB 4.931,1.687 5.153,1.858 0.221,0.171 10 DD 2.319,2.077 2.514,2.213 0.195,0.137 10 H2 3.103,3.652 3.315,3.791 0.212,0.139 10 DB 4.143,4.686 4.550,4.825 0.408,0.139 10 BECU 1.755,7.545 2.325,7.683 0.570,0.137 10 CANH*A 0.023,7.679 0.593,7.818 0.570,0.140 10 CANP*B 1.645,8.171 2.215,8.312 0.570,0.141 10 CANL*A 0.218,8.241 0.788,8.380 0.570,0.138 10 CANN*B 3.81,4.326 4.022,4.743 4.022,4.743 4.129,4.743 false 1.481,6.463 1.888,6.602 0.408,0.139 10 GND1 1.148,6.103 1.36,6.52 1.36,6.52 1.467,6.52 false 1.625,5.189 1.844,5.328 0.219,0.139 10 DD 1.073,6.983 1.269,7.122 0.196,0.139 10 H2 0.888,7.978 0.637,7.744 0.637,7.744 0.587,7.744 false 1.006,7.999 0.864,8.306 0.864,8.306 0.789,8.306 false 1.416,7.84 1.668,7.605 1.668,7.605 1.745,7.605 false 1.298,7.86 1.556,8.245 1.556,8.245 1.631,8.245 false

Text in Illustration
*A for V1 Bus *B for MS Bus

a.

Disconnect the H2, DB and DD main body ECU (cowl side junction block LH) connectors.


b.

Measure the resistance according to the value(s) in the table below.

for V1 Bus
Terminal No. (Symbol) Wiring Color Switch Condition Specified Condition
H2-5 (CANH) - H2-6 (CANL) L - W Ignition switch off 54 to 69 Ω
H2-5 (CANH) - DD-62 (GND1) L - W-B Ignition switch off 200 Ω or higher
H2-6 (CANL) - DD-62 (GND1) W - W-B Ignition switch off 200 Ω or higher
H2-5 (CANH) - DB-13 (BECU) L - GR Ignition switch off 6 kΩ or higher
H2-6 (CANL) - DB-13 (BECU) W - GR Ignition switch off 6 kΩ or higher

for MS Bus
Terminal No. (Symbol) Wiring Color Switch Condition Specified Condition
H2-16 (CANP) - H2-15 (CANN) B - W Ignition switch off 108 to 132 Ω
H2-16 (CANP) - DD-62 (GND1) B - W-B Ignition switch off 200 Ω or higher
H2-15 (CANN) - DD-62 (GND1) W - W-B Ignition switch off 200 Ω or higher
H2-16 (CANP) - DB-13 (BECU) B - GR Ignition switch off 6 kΩ or higher
H2-15 (CANN) - DB-13 (BECU) W - GR Ignition switch off 6 kΩ or higher



CHECK ECM


U153496E01
6.325,0.783 6.698,0.923 0.373,0.140 10 BATT 1.419,2.265 1.611,2.404 0.191,0.140 10 E1 5.164,0.529 5.430,0.666 0.267,0.138 10 A27 2.763,0.529 3.036,0.666 0.274,0.138 10 D56 4.124,0.363 4.544,0.502 0.420,0.140 10 CANH 4.004,0.641 4.393,0.782 0.389,0.141 10 CANL 4.39,0.703 4.492,0.703 4.492,0.703 4.611,1.085 false 4.733,1.085 4.632,0.427 4.632,0.427 4.544,0.427 false 5.945,1.082 6.219,0.851 6.219,0.851 6.31,0.851 false 1.933,1.791 1.725,2.332 1.725,2.332 1.599,2.332 false

a.

Disconnect the A27 and D56 ECM connectors.


b.

Measure the resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Switch Condition Specified Condition
A27-10 (CANH) - A27-11 (CANL) GR - W Ignition switch off 108 to 132 Ω
A27-10 (CANH) - D56-81 (E1) GR - BR Ignition switch off 200 Ω or higher
A27-11 (CANL) - D56-81 (E1) W - BR Ignition switch off 200 Ω or higher
A27-10 (CANH) - A27-1 (BATT) GR - L Ignition switch off 6 kΩ or higher
A27-11 (CANL) - A27-1 (BATT) W - L Ignition switch off 6 kΩ or higher



CHECK AIR CONDITIONING AMPLIFIER ASSEMBLY


U153490E01
3.786,0.7 4.064,0.845 0.279,0.145 10 H24 4.144,1.918 4.661,2.057 0.517,0.139 10 CANH 2.948,2.086 3.465,2.225 0.517,0.139 10 CANL 5.134,1.899 5.651,2.039 0.517,0.139 10 B 2.731,1.892 3.248,2.032 0.517,0.139 10 GND 3.522,1.44 3.134,1.96 3.134,1.96 3.062,1.96 false 3.841,1.44 4.055,1.969 4.055,1.969 4.128,1.969 false 3.316,2.144 3.384,2.144 3.384,2.144 3.741,1.44 false 4.948,1.56 5.042,1.96 5.042,1.96 5.119,1.96 false

a.

Disconnect the H24 air conditioning amplifier assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Switch Condition Specified Condition
H24-11 (CANH) - H24-12 (CANL) B - W Ignition switch off 54 to 69 Ω
H24-11 (CANH) - H24-14 (GND) B - W-B Ignition switch off 200 Ω or higher
H24-12 (CANL) - H24-14 (GND) W - W-B Ignition switch off 200 Ω or higher
H24-11 (CANH) - H24-21 (B) B - R Ignition switch off 6 kΩ or higher
H24-12 (CANL) - H24-21 (B) W - R Ignition switch off 6 kΩ or higher



CHECK CENTER AIRBAG SENSOR ASSEMBLY


U153539E01
2.324,2.435 2.841,2.572 0.517,0.137 10 CANH 2.513,2.134 3.030,2.271 0.517,0.137 10 CANL 1.428,2.132 1.626,2.271 0.198,0.139 10 E1 1.694,0.606 1.968,0.747 0.274,0.140 10 H56 6.51,2.108 6.802,2.245 0.293,0.137 10 BAT 5.603,0.77 5.877,0.910 0.274,0.140 10 H19 6.258,1.769 6.405,2.176 6.405,2.176 6.475,2.176 false 1.826,1.793 1.679,2.199 1.679,2.199 1.609,2.199 false 2.281,1.793 2.428,2.199 2.428,2.199 2.498,2.199 false 2.125,1.55 2.239,2.493 2.239,2.493 2.309,2.493 false

a.

Disconnect the H56 center airbag sensor assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Switch Condition Specified Condition
H56-13 (CANH) - H56-22 (CANL) BR - W Ignition switch off 54 to 69 Ω
H56-13 (CANH) - H56-25 (E1) BR - W-B Ignition switch off 200 Ω or higher
H56-22 (CANL) - H56-25 (E1) W - W-B Ignition switch off 200 Ω or higher
H56-13 (CANH) - H19-16 (BAT) BR - P Ignition switch off 6 kΩ or higher
H56-22 (CANL) - H19-16 (BAT) W - P Ignition switch off 6 kΩ or higher



CHECK COMBINATION METER ASSEMBLY


U153495E02
3.083,1.5 2.865,1.979 2.865,1.979 2.75,1.979 false 3.031,2.208 3.156,2.208 3.156,2.208 3.25,1.5 false 4.99,1.5 5.208,1.979 5.208,1.979 5.323,1.979 false 5.052,2.208 4.917,2.208 4.917,2.208 4.833,1.5 false 2.01,0.594 2.156,0.594 2.156,0.594 2.479,1.188 false 1.75,0.885 1.854,0.885 1.854,0.885 2.177,1.438 false 3.479,0.49 3.781,0.688 0.302,0.198 10 false H37 1.844,0.5 1.99,0.688 0.146,0.188 10 false B 1.521,0.802 2.042,0.99 0.521,0.188 10 false E1 2.198,1.917 2.896,2.104 0.698,0.188 10 false CANL*A 2.448,2.135 3.021,2.323 0.573,0.188 10 false CANH*A 5.063,2.135 5.708,2.323 0.646,0.188 10 false CANH*B 5.344,1.917 5.958,2.104 0.615,0.188 10 false CANL*B

Text in Illustration
*A for V1 Bus *B for MS Bus

a.

Disconnect the H37 combination meter assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

for V1 Bus
Terminal No. (Symbol) Wiring Color Switch Condition Specified Condition
H37-33 (CANH) - H37-34 (CANL) SB - W Ignition switch off 108 to 132 Ω
H37-33 (CANH) - H37-40 (E1) SB - W-B Ignition switch off 200 Ω or higher
H37-34 (CANL) - H37-40 (E1) W - W-B Ignition switch off 200 Ω or higher
H37-33 (CANH) - H37-18 (B) SB - LG Ignition switch off 6 kΩ or higher
H37-34 (CANL) - H37-18 (B) W - LG Ignition switch off 6 kΩ or higher

for MS Bus
Terminal No. (Symbol) Wiring Color Switch Condition Specified Condition
H37-22 (CANH) - H37-21 (CANL) Y - W Ignition switch off 108 to 132 Ω
H37-22 (CANH) - H37-40 (E1) Y - W-B Ignition switch off 200 Ω or higher
H37-21 (CANL) - H37-40 (E1) W - W-B Ignition switch off 200 Ω or higher
H37-22 (CANH) - H37-18 (B) Y - LG Ignition switch off 6 kΩ or higher
H37-21 (CANL) - H37-18 (B) W - LG Ignition switch off 6 kΩ or higher



CHECK STEERING ANGLE SENSOR


U153497E01
3.523,0.717 3.726,0.855 0.203,0.138 10 H6 2.291,1.755 2.808,1.939 0.517,0.184 10 CANH 2.499,1.951 3.016,2.135 0.517,0.184 10 CANL 4.191,1.955 4.708,2.139 0.517,0.184 10 BAT 4.383,1.75 4.900,1.934 0.517,0.184 10 ESS 2.968,1.531 2.811,1.819 2.811,1.819 2.706,1.819 false 2.895,2.022 2.968,2.022 2.968,2.022 3.117,1.529 false 4.107,1.531 4.264,1.819 4.264,1.819 4.369,1.819 false 4.18,2.022 4.107,2.022 4.107,2.022 3.958,1.529 false

a.

Disconnect the H6 steering angle sensor connector.


b.

Measure the resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Switch Condition Specified Condition
H6-10 (CANH) - H6-9 (CANL) G - W Ignition switch off 54 to 69 Ω
H6-10 (CANH) - H6-2 (ESS) G - W-B Ignition switch off 200 Ω or higher
H6-9 (CANL) - H6-2 (ESS) W - W-B Ignition switch off 200 Ω or higher
H6-10 (CANH) - H6-3 (BAT) G - R Ignition switch off 6 kΩ or higher
H6-9 (CANL) - H6-3 (BAT) W - R Ignition switch off 6 kΩ or higher



CHECK 4 WHEEL DRIVE CONTROL ECU (4WD CONTROL ECU) (for 4WD)


U153491E01
5.813,1.625 5.917,1.865 5.917,1.865 5.99,1.865 false 0.823,1.375 0.646,1.792 0.646,1.792 0.563,1.792 false 2.521,1.375 2.708,1.792 2.708,1.792 2.781,1.792 false 0.906,1.375 1.094,1.792 1.094,1.792 1.167,1.792 false 2.802,1.729 3.323,1.917 0.521,0.188 10 false GND 1.208,1.729 1.802,1.927 0.594,0.198 10 false CANH 0.156,1.708 0.625,1.906 0.469,0.198 10 false CANL 1.438,0.885 1.75,1.052 0.313,0.167 10 false A28 2.698,0.885 3.042,1.083 0.344,0.198 10 false A29 6.01,1.802 6.406,1.948 0.396,0.146 10 false BAT 5.156,0.667 5.615,0.906 0.458,0.24 10 false H19

a.

Disconnect the A28 and A29 4 wheel drive control ECU (4WD control ECU) connectors.


b.

Measure the resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Switch Condition Specified Condition
A28-19 (CANH) - A28-20 (CANL) BE - W Ignition switch off 54 to 69 Ω
A28-19 (CANH) - A29-4 (GND) BE - W-B Ignition switch off 200 Ω or higher
A28-20 (CANL) - A29-4 (GND) W - W-B Ignition switch off 200 Ω or higher
A28-19 (CANH) - H19-16 (BAT) BE - P Ignition switch off 6 kΩ or higher
A28-20 (CANL) - H19-16 (BAT) W - P Ignition switch off 6 kΩ or higher



CHECK BUS BUFFER ECU (w/ Bus Buffer ECU)


U153829E01
0.636,0.826 1.034,0.966 0.398,0.140 10 CAN+ 0.801,1.651 1.168,1.789 0.368,0.137 10 CAN- 2.544,1.107 2.817,1.245 0.273,0.138 10 H66 1.395,1.157 1.192,0.912 1.192,0.912 1.117,0.912 false 1.262,1.723 1.336,1.723 1.336,1.723 1.745,1.256 false

a.

Disconnect the H66 bus buffer ECU connector.


b.

Measure the resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Switch Condition Specified Condition
H66-3 (CAN+) - H66-2 (CAN-) P - W Ignition switch off 54 to 69 Ω



CHECK FRONT POWER SEAT SWITCH LH (POWER SEAT CONTROL ECU) (w/ Seat Memory)


U153492E01
3.863,1.94 4.054,2.078 0.191,0.138 10 +B 2.777,1.942 3.105,2.080 0.327,0.138 10 GND 3.019,0.75 3.283,0.887 0.265,0.137 10 X10 4.074,0.936 4.339,1.074 0.265,0.137 10 X11 4.665,1.764 5.076,1.902 0.411,0.139 10 CANH 4.665,1.265 5.056,1.405 0.392,0.140 10 CANL 4.35,1.632 4.573,1.828 4.573,1.828 4.65,1.828 false 4.35,1.517 4.573,1.321 4.573,1.321 4.65,1.321 false 3.562,1.637 3.749,2.01 3.749,2.01 3.833,2.01 false 3.111,2.01 3.23,2.01 3.23,2.01 3.541,1.452 false

a.

Disconnect the X10 and X11 front power seat switch LH (power seat control ECU) connectors.


b.

Measure the resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Switch Condition Specified Condition
X11-5 (CANH) - X11-1 (CANL) GR - W Ignition switch off 54 to 69 Ω
X11-5 (CANH) - X10-1 (GND) GR - W-B Ignition switch off 200 Ω or higher
X11-1 (CANL) - X10-1 (GND) W - W-B Ignition switch off 200 Ω or higher
X11-5 (CANH) - X10-5 (+B) GR - L Ignition switch off 6 kΩ or higher
X11-1 (CANL) - X10-5 (+B) W - L Ignition switch off 6 kΩ or higher



CHECK OUTER MIRROR CONTROL ECU ASSEMBLY (w/ Seat Memory)


U153493E02
4.229,1.427 4.49,1.865 4.49,1.865 4.583,1.865 false 4.375,2.094 4.302,2.094 4.302,2.094 4.208,1.625 false 3.563,2.313 3.635,2.313 3.635,2.313 3.813,1.583 false 3.354,1.917 3.51,1.917 3.51,1.917 3.771,1.469 false 4.646,1.802 4.896,2.01 0.25,0.208 10 false B 4.417,2.021 4.938,2.167 0.521,0.146 10 false GND 2.99,1.813 3.51,2 0.521,0.188 10 false CAN 3.135,2.24 3.656,2.438 0.521,0.198 10 false CGND 4.354,0.896 4.677,1.104 0.323,0.208 10 false M7 2.865,0.885 3.115,1.063 0.25,0.177 10 false M8

a.

Disconnect the M7 and M8 outer mirror control ECU assembly connectors.


b.

Measure the resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Switch Condition Specified Condition
M8-1 (CAN) - M8-21 (CGND) LG - W Ignition switch off 54 to 69 Ω
M8-1 (CAN) - M7-9 (GND) LG - W-B Ignition switch off 200 Ω or higher
M8-21 (CGND) - M7-9 (GND) W - W-B Ignition switch off 200 Ω or higher
M8-1 (CAN) - M7-3 (B) LG - R Ignition switch off 6 kΩ or higher
M8-21 (CGND) - M7-3 (B) W - R Ignition switch off 6 kΩ or higher



CHECK MULTIPLEX TILT AND TELESCOPIC ECU (w/ Seat Memory)


U153494E02
4.021,1.5 4.375,1.146 4.375,1.146 4.5,1.146 false 3.573,1.781 3.344,2.083 3.344,2.083 3.24,2.083 false 4.021,1.76 4.25,2.063 4.25,2.063 4.365,2.063 false 3.01,0.927 3.115,0.927 3.115,0.927 3.542,1.521 false 3.49,0.75 3.813,0.958 0.323,0.208 10 false H57 2.573,0.844 3.094,1.031 0.521,0.188 10 false CANH 2.802,2.021 3.323,2.208 0.521,0.188 10 false CANL 4.583,1.073 4.792,1.208 0.208,0.135 10 false +B 4.438,1.969 4.958,2.156 0.521,0.188 10 false GND

a.

Disconnect the H57 multiplex tilt and telescopic ECU connector.


b.

Measure the resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Switch Condition Specified Condition
H57-5 (CANH) - H57-14 (CANL) BE - W Ignition switch off 54 to 69 Ω
H57-5 (CANH) - H57-11 (GND) BE - W-B Ignition switch off 200 Ω or higher
H57-14 (CANL) - H57-11 (GND) W - W-B Ignition switch off 200 Ω or higher
H57-5 (CANH) - H57-2 (+B) BE - V Ignition switch off 6 kΩ or higher
H57-14 (CANL) - H57-2 (+B) W - V Ignition switch off 6 kΩ or higher



CHECK DISTANCE CONTROL ECU ASSEMBLY (w/ Dynamic Laser Cruise Control System)


U153894E01
1.771,1.646 1.906,1.646 1.906,1.646 2.135,0.99 false 1.333,1.469 1.49,1.469 1.49,1.469 2,0.99 false 1.094,0.677 1.229,0.677 1.229,0.677 1.448,0.875 false 6.135,1.479 5.979,1.479 5.979,1.479 5.833,1.208 false 1.344,1.573 1.781,1.719 0.438,0.146 10 false CANH 2.156,0.219 2.417,0.354 0.26,0.135 10 false A43 5.177,0.219 5.448,0.354 0.271,0.135 10 false H19 6.156,1.406 6.469,1.552 0.313,0.146 10 false BAT 0.938,1.396 1.344,1.531 0.406,0.135 10 false CANL 0.76,0.615 1.104,0.781 0.344,0.167 10 false GND

a.

Disconnect the A43 distance control ECU assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Switch Condition Specified Condition
A43-8 (CANH) - A43-9 (CANL) BE - W Ignition switch off 54 to 69 Ω
A43-8 (CANH) - A43-12 (GND) BE - BR Ignition switch off 200 Ω or higher
A43-9 (CANL) - A43-12 (GND) W - BR Ignition switch off 200 Ω or higher
A43-8 (CANH) - H19-16 (BAT) BE - P Ignition switch off 6 kΩ or higher
A43-9 (CANL) - H19-16 (BAT) W - P Ignition switch off 6 kΩ or higher



CHECK POWER STEERING ECU ASSEMBLY


U153679E02
5.771,1.292 5.927,1.594 5.927,1.594 6.021,1.594 false 1.979,1.177 1.833,1.49 1.833,1.49 1.729,1.49 false 2.281,1.188 2.427,1.5 2.427,1.5 2.542,1.5 false 2.344,1.656 2.219,1.656 2.219,1.656 2.125,1.188 false 0.417,0.958 0.771,1.094 0.354,0.135 10 false H117 2.594,1.396 3.042,1.625 0.448,0.229 10 false CANH 2.406,1.573 2.885,1.75 0.479,0.177 10 false CANL 1.385,1.417 1.844,1.604 0.458,0.188 10 false GND 6.083,1.51 6.49,1.74 0.406,0.229 10 false BAT 4.01,1.021 4.281,1.167 0.271,0.146 10 false H19

a.

Disconnect the H117 power steering ECU assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Switch Condition Specified Condition
H117-1 (CANH) - H117-2 (CANL) GR - W Ignition switch off 54 to 69 Ω
H117-1 (CANH) - H117-3 (GND) GR - W-B Ignition switch off 200 Ω or higher
H117-2 (CANL) - H117-3 (GND) W - W-B Ignition switch off 200 Ω or higher
H117-1 (CANH) - H19-16 (BAT) GR - P Ignition switch off 6 kΩ or higher
H117-2 (CANL) - H19-16 (BAT) W - P Ignition switch off 6 kΩ or higher



CHECK SUSPENSION CONTROL ECU (w/ Air Suspension System)


U154021E02
4.813,1.521 4.688,1.135 4.688,1.135 4.615,1.135 false 6.042,1.771 6.219,1.594 6.219,1.594 6.333,1.594 false 5.854,1.865 6.063,2.333 6.063,2.333 6.177,2.333 false 5.427,1.51 5.625,1.156 5.625,1.156 5.729,1.156 false 4.281,1.042 4.802,1.229 0.521,0.188 10 false GND 6.385,1.521 6.906,1.75 0.521,0.229 10 false CANH 5.792,1.094 6.313,1.229 0.521,0.135 10 false B 6.219,2.26 6.74,2.448 0.521,0.188 10 false CANL 5.135,0.99 5.521,1.188 0.385,0.198 10 false O16

a.

Disconnect the O16 suspension control ECU connector.


b.

Measure the resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Switch Condition Specified Condition
O16-7 (CANH) - O16-8 (CANL) B - W Ignition switch off 54 to 69 Ω
O16-7 (CANH) - O16-5 (GND) B - W-B Ignition switch off 200 Ω or higher
O16-8 (CANL) - O16-5 (GND) W - W-B Ignition switch off 200 Ω or higher
O16-7 (CANH) - O16-3 (B) B - SB Ignition switch off 6 kΩ or higher
O16-8 (CANL) - O16-3 (B) W - SB Ignition switch off 6 kΩ or higher



CHECK POWER BACK DOOR UNIT ASSEMBLY (POWER BACK DOOR ECU) (w/ Power Back Door System)


U154205E01
3.469,0.619 3.750,0.757 0.282,0.138 10 O30 2.005,0.847 2.137,1.028 0.132,0.181 10 B 3.909,2.239 4.338,2.380 0.429,0.140 10 CANP 2.048,2.099 2.388,2.280 0.340,0.181 10 GND 4.215,2.075 4.644,2.211 0.429,0.137 10 CANN 2.499,1.296 2.201,0.914 2.201,0.914 2.128,0.914 false 2.381,2.161 2.479,2.161 2.479,2.161 2.815,1.425 false 3.816,1.425 4.113,2.132 4.113,2.132 4.187,2.132 false 3.889,2.304 3.791,2.304 3.791,2.304 3.658,1.425 false

a.

Disconnect the O30 power back door unit assembly (power back door ECU) connector.


b.

Measure the resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Switch Condition Specified Condition
O30-6 (CANP) - O30-5 (CANN) B - W Ignition switch off 54 to 69 Ω
O30-6 (CANP) - O30-11 (GND) B - W-B Ignition switch off 200 Ω or higher
O30-5 (CANN) - O30-11 (GND) W - W-B Ignition switch off 200 Ω or higher
O30-6 (CANP) - O30-12 (B) B - L Ignition switch off 6 kΩ or higher
O30-5 (CANN) - O30-12 (B) W - L Ignition switch off 6 kΩ or higher



CHECK NETWORK GATEWAY ECU (w/ Network Gateway ECU)


U153744E01
3.108,1.161 2.878,0.657 2.878,0.657 2.745,0.657 false 2.989,1.387 2.772,1.995 2.772,1.995 2.681,1.995 false 2.891,2.219 2.968,2.219 2.968,2.219 3.114,1.404 false 4.073,1.161 4.302,0.657 4.302,0.657 4.435,0.657 false 3.48,1.387 3.696,1.995 3.696,1.995 3.787,1.995 false 3.577,2.219 3.5,2.219 3.5,2.219 3.354,1.404 false 3.349,0.558 3.699,0.704 0.350,0.145 10 H120 4.45,0.592 4.953,0.737 0.503,0.145 10 BATT 2.398,0.592 2.901,0.737 0.503,0.145 10 GND 3.816,1.93 4.354,2.075 0.538,0.145 10 CA2L*B 3.602,2.144 4.140,2.290 0.538,0.145 10 CA2H*B 2.128,1.93 2.666,2.075 0.538,0.145 10 CA1H*A 2.354,2.156 2.892,2.301 0.538,0.145 10 CA1L*A

Text in Illustration
*A for V1 Bus *B for V2 Bus

a.

Disconnect the H120 network gateway ECU connector.


b.

Measure the resistance according to the value(s) in the table below.

for V1 Bus
Terminal No. (Symbol) Wiring Color Switch Condition Specified Condition
H120-16 (CA1H) - H120-15 (CA1L) SB - W Ignition switch off 54 to 69 Ω
H120-16 (CA1H) - H120-4 (GND) SB - W-B Ignition switch off 200 Ω or higher
H120-15 (CA1L) - H120-4 (GND) W - W-B Ignition switch off 200 Ω or higher
H120-16 (CA1H) - H120-2 (BATT) SB - L Ignition switch off 6 kΩ or higher
H120-15 (CA1L) - H120-2 (BATT) W - L Ignition switch off 6 kΩ or higher

for V2 Bus
Terminal No. (Symbol) Wiring Color Switch Condition Specified Condition
H120-13 (CA2H) - H120-12 (CA2L) L - W Ignition switch off 108 to 132 Ω
H120-13 (CA2H) - H120-4 (GND) L - W-B Ignition switch off 200 Ω or higher
H120-12 (CA2L) - H120-4 (GND) W - W-B Ignition switch off 200 Ω or higher
H120-13 (CA2H) - H120-2 (BATT) L - L Ignition switch off 6 kΩ or higher
H120-12 (CA2L) - H120-2 (BATT) W - L Ignition switch off 6 kΩ or higher



CHECK BLIND SPOT MONITOR SENSOR LH (w/ Blind Spot Monitor Sensor)


U153745E02
1.479,0.906 1.25,0.573 1.25,0.573 1.115,0.573 false 1.542,1.219 1.313,1.552 1.313,1.552 1.177,1.552 false 2.073,0.927 2.344,0.656 2.344,0.656 2.469,0.656 false 5.74,1.281 5.885,1.573 5.885,1.573 6.01,1.573 false 2.531,0.583 3.104,0.729 0.573,0.146 10 false BLGD 0.729,0.51 1.302,0.656 0.573,0.146 10 false CA1N 0.75,1.469 1.323,1.615 0.573,0.146 10 false CA1P 6.031,1.49 6.604,1.635 0.573,0.146 10 false BAT 3.948,1 4.229,1.146 0.281,0.146 10 false H19 0.677,1.031 0.958,1.177 0.281,0.146 10 false O46

a.

Disconnect the O46 blind spot monitor sensor LH connector.


b.

Measure the resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Switch Condition Specified Condition
O46-8 (CA1P) - O46-4 (CA1N) BE - W Ignition switch off 54 to 69 Ω
O46-8 (CA1P) - O46-1 (BLGD) BE - W-B Ignition switch off 200 Ω or higher
O46-4 (CA1N) - O46-1 (BLGD) W - W-B Ignition switch off 200 Ω or higher
O46-8 (CA1P) - H19-16 (BAT) BE - P Ignition switch off 6 kΩ or higher
O46-4 (CA1N) - H19-16 (BAT) W - P Ignition switch off 6 kΩ or higher



CHECK BLIND SPOT MONITOR SENSOR RH (w/ Blind Spot Monitor Sensor)


U153746E02
1.479,0.969 1.25,0.635 1.25,0.635 1.125,0.635 false 1.5,1.198 1.271,1.531 1.271,1.531 1.146,1.531 false 2.083,0.906 2.354,0.635 2.354,0.635 2.479,0.635 false 5.719,1.281 5.865,1.573 5.865,1.573 6,1.573 false 0.677,1.042 0.948,1.188 0.271,0.146 10 false P25 2.542,0.573 3.115,0.719 0.573,0.146 10 false BRGD 0.677,0.552 1.146,0.708 0.469,0.156 10 false CA1N 0.729,1.469 1.135,1.615 0.406,0.146 10 false CA1P 6.073,1.49 6.646,1.635 0.573,0.146 10 false BAT 3.948,1 4.229,1.146 0.281,0.146 10 false H19

a.

Disconnect the P25 blind spot monitor sensor RH connector.


b.

Measure the resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Switch Condition Specified Condition
P25-8 (CA1P) - P25-4 (CA1N) R - W Ignition switch off 54 to 69 Ω
P25-8 (CA1P) - P25-1 (BRGD) R - W-B Ignition switch off 200 Ω or higher
P25-4 (CA1N) - P25-1 (BRGD) W - W-B Ignition switch off 200 Ω or higher
P25-8 (CA1P) - H19-16 (BAT) R - P Ignition switch off 6 kΩ or higher
P25-4 (CA1N) - H19-16 (BAT) W - P Ignition switch off 6 kΩ or higher