Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM
RM27L0U _57 Power Source / Network _049335 NETWORKING _0235802 CAN COMMUNICATION SYSTEM J

NETWORKING  CAN COMMUNICATION SYSTEM  Steering Angle Sensor Communication Stop Mode  


DESCRIPTION

Detection Item Symptom Trouble Area
Steering Angle Sensor Communication Stop Mode Either condition is met:
·

"Spiral cable (Steering Angle Sensor)" is not displayed on the "Bus Check" screen.

·

"Steering Angle Sensor Communication Stop Mode" in "DTC Communication Table" applies.


·

Power source or inside of steering angle sensor

·

Steering angle sensor CAN branch wire or connector

·

Steering angle sensor



WIRING DIAGRAM

C245635E04
0.609,1.953 2.226,2.096 1.617,0.143 10 No. 1 Junction Connector 5.758,0.987 6.275,1.125 0.517,0.138 10 CANH 5.758,1.427 6.275,1.565 0.517,0.138 10 CANL 5.501,1.329 5.599,1.468 0.098,0.139 10 9 5.501,3.857 5.599,3.996 0.098,0.139 10 2 5.498,3.046 5.599,3.185 0.101,0.139 10 1 5.504,2.249 5.599,2.388 0.095,0.139 10 3 5.424,0.886 5.598,1.025 0.174,0.139 10 10 5.758,2.353 6.275,2.492 0.517,0.138 10 BAT 5.76,3.965 6.277,4.102 0.517,0.137 10 ESS 4.399,2.184 4.926,2.324 0.527,0.140 10 ECU-B1 2.059,2.345 2.857,2.487 0.799,0.141 10 from Battery 1.625,3.167 2.853,3.304 1.228,0.137 10 from IG No.1 Relay 5.76,3.159 6.277,3.296 0.517,0.137 10 IG 4.236,3.029 5.086,3.166 0.850,0.137 10 ECU-IG No.1 5.405,4.75 5.701,4.889 0.296,0.138 10 H6 0.609,1.809 0.974,1.947 0.365,0.138 10 H119 1.877,0.886 1.986,1.028 0.109,0.142 10 4 1.877,1.329 2.051,1.473 0.174,0.143 10 15 5.405,4.904 6.840,5.050 1.435,0.146 10 Steering Angle Sensor

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


HINT:

Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.


PROCEDURE

1.PRECAUTION
NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).



NEXT

2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
a.

Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the CAN main wire and the CAN branch wire.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.


NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).




NEXT

3.CHECK FOR OPEN IN CAN BUS WIRE (STEERING ANGLE SENSOR CAN BRANCH WIRE)
3.CHECK FOR OPEN IN CAN BUS WIRE (STEERING ANGLE SENSOR CAN BRANCH WIRE)
a.
U153835E01
1.172,1.309 0.944,1.537 0.944,1.537 0.834,1.537 false 1.008,1.802 1.068,1.802 1.068,1.802 1.307,1.309 false 0.338,1.451 0.759,1.594 0.421,0.143 10 CANH 2.789,1.199 2.984,1.342 0.195,0.143 10 H6 0.51,1.72 0.931,1.863 0.421,0.143 10 CANL 0.058,0.035 0.253,0.178 0.195,0.143 10 *a

Disconnect the H6 steering angle sensor connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
H6-10 (CANH) - H6-9 (CANL) Ignition switch off 54 to 69 Ω


Text in Illustration
*a Rear view of wire harness connector
(to Steering Angle Sensor)



OK

4.CHECK HARNESS AND CONNECTOR (STEERING ANGLE SENSOR - BATTERY AND BODY GROUND)

NG

REPAIR OR REPLACE STEERING ANGLE SENSOR CAN BRANCH WIRE OR CONNECTOR (CANH, CANL)

4.CHECK HARNESS AND CONNECTOR (STEERING ANGLE SENSOR - BATTERY AND BODY GROUND)
a.
U153836E01
2.213,1.309 2.441,1.537 2.441,1.537 2.551,1.537 false 2.376,1.802 2.316,1.802 2.316,1.802 2.078,1.309 false 2.59,1.451 3.011,1.594 0.421,0.143 10 ESS 2.673,0.987 3.094,1.130 0.421,0.143 10 IG 0.491,1.199 0.685,1.342 0.195,0.143 10 H6 2.401,1.72 2.821,1.863 0.421,0.143 10 BAT 0.058,0.035 0.253,0.178 0.195,0.143 10 *a 2.348,1.23 2.545,1.062 2.545,1.062 2.651,1.062 false

Connect the cable to the negative (-) battery terminal.

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).



b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
H6-3 (BAT) - Body ground Always 11 to 14 V
H6-1 (IG) - Body ground Ignition switch ON 11 to 14 V



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H6-2 (ESS) - Body ground Always Below 1 Ω



Text in Illustration
*a Front view of wire harness connector
(to Steering Angle Sensor)


OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR