FAIL-SAFE FUNCTION
When communication fails in any of the main wires (communication lines) due to a short circuit or other causes, the fail-safe function, which is specified for each system, operates to prevent the system from malfunctioning.
The table below shows the effects on each system when communication is impossible. For further details, refer to each system.
| Function | Behavior during CAN Failure | |||
|---|---|---|---|---|
1.
Control Master 2.
System Related |
Vehicle Behavior | Indicator and Buzzer | Diagnostic Trouble Code | |
| Blind Spot Detection
(Warns the driver when the system detects a vehicle in the blind spot of an outer mirror.) |
1.
Main body ECU (cowl side junction block LH), Blind spot monitor sensor LH, Blind spot monitor sensor RH 2.
ECM, Brake actuator assembly (skid control ECU), Steering angle sensor |
Maintains previous values. | "CHECK BSM SYSTEM" is displayed on the multi-information display. | ·
U0100 ·
U0126 ·
U0129 ·
U0142 ·
U0232 ·
U0233 |
| Relay Function
(Transmits relay frames and does not transmit non-relay frames.) |
1.
Network gateway ECU 2.
Main body ECU (cowl side junction block LH), ECM, Brake actuator assembly (skid control ECU), steering angle sensor, Combination meter assembly, Center airbag sensor assembly, Air conditioning amplifier assembly, Bus buffer ECU, Blind spot monitor sensor LH, Blind spot monitor sensor RH, DLC3, 4 wheel drive control ECU (4WD control ECU), Suspension control ECU, Power steering ECU assembly, Distance control ECU assembly |
CAN controller is reset. | Nothing | Nothing |
| Diagnostic Function
(Determines the connection and communication status of ECUs which are connected to the V2 bus) |
1.
Network gateway ECU 2.
Blind spot monitor sensor LH, Blind spot monitor sensor RH, Distance control ECU assembly |
CAN controller is reset. | Nothing | ·
U0104 ·
U0232 ·
U0233 ·
U1002 |
| NM Function
(Performs communication via NM frames with ECUs that are equipped with NM, and controls the CAN communication sleep/wake up functions.) |
1.
Network gateway ECU 2.
Main body ECU (cowl side junction block LH), Combination meter assembly, Bus buffer ECU |
CAN controller is reset. | Nothing | Nothing |
| CCP Function
(Communicates with devices connected via the V-bus and monitors the RAM in the gateway ECU.) |
1.
Network gateway ECU 2.
DLC3 |
CAN controller is reset. | Nothing | Nothing |
| VFC control
(Changes the power steering fluid flow according to the state of the vehicle using the vehicle speed, engine speed, steering angle and towing information.) |
1.
Power steering ECU assembly 2.
ECM, Brake actuator assembly (skid control ECU), Steering angle sensor |
Alternative control (The steering angle, vehicle speed and engine speed are fixed.) | PPS indicator light turns on | U0073 |
| ACC
(Acceleration/deceleration control when following the vehicle in front.) |
1.
Distance control ECU assembly 2.
Main body ECU (cowl side junction block LH), ECM, Brake actuator assembly (skid control ECU), Steering angle sensor, Combination meter assembly |
ACC control is canceled. | "Check Cruise System" is displayed on the multi-information display.
The master warning light turns on and the warning buzzer sounds. |
·
U0100 ·
U0122 ·
U0123 ·
U0126 ·
U1101 |
| Air conditioning control
(Performs engine-linked control based on sensor information and controls the air conditioning and panel.) |
1.
Air conditioning amplifier 2.
Main body ECU (cowl side junction block LH), ECM, Combination meter assembly, Bus buffer ECU |
Maintains previous values. | Nothing | Nothing |
| Power back door operation condition
(Prohibit PBD function according to vehicle condition (IG, shift position P, vehicle speed, remote start, lock position) |
1.
Power back door unit assembly (power back door ECU) 2.
ECM, Combination meter assembly, Main body ECU (cowl side junction block LH) |
PBD system does not operate. (When a start up signal is received, a buzzer sounds indicating that operation conditions are not met.) | Buzzer | Nothing |
| Power back door operation request
(Start PBD operation by receiving request trigger from operation switch, wireless switch) |
1.
Power back door unit assembly (power back door ECU) 2.
Main body ECU (cowl side junction block LH) |
PBD does not work. | Nothing | Nothing |
| Power back door operation status output
(Output hazard ON request and door status during PBD working) |
1.
Power back door unit assembly (power back door ECU) 2.
Main body ECU (cowl side junction block LH) |
·
When the back door is opening, the illumination of the indicator in the meter may be delayed. ·
When the back door starts to open, the illumination of the hazard warning lights may be delayed. ·
When a back door unlock request signal is sent, the unlocking of the back door may be delayed and the power back door may not operate. |
Nothing | Nothing |
| Driver side seat memory system
(Memorizes and recalls the driver side seat, steering wheel and outside mirror positions.) |
1.
Front power seat switch LH (power seat control ECU) 2.
Outer mirror control ECU assembly, Multiplex tilt and telescopic ECU, Main body ECU (cowl side junction block LH), ECM, Combination meter assembly |
Position memorization and recall cannot be performed. The tilt and telescopic system does not operate. | Nothing | Nothing |
| 2WD-4WD switching limitation
(Switching between 2WD and 4WD is prohibited when the vehicle speed is outside the acceptable range.) |
1.
4 wheel drive control ECU (4WD control ECU) 2.
Brake actuator assembly (skid control ECU) |
Switching between 2WD and 4WD is prohibited. | Indicator light blinks | Nothing |
| High-Low switching limitation
(Prohibits High-Low switching when the vehicle speed or engine speed is outside the acceptable range or the A/T is not in N during the A/T status check.) |
1.
4 wheel drive control ECU (4WD control ECU) 2.
ECM, Brake actuator assembly (skid control ECU) |
High-Low switching is prohibited. | Indicator light blinks | Nothing |
| Center differential lock switching control
(Center differential lock switching is prohibited when there is a vehicle speed violation or large difference in wheel speeds.) |
1.
4 wheel drive control ECU (4WD control ECU) 2.
Brake actuator assembly (skid control ECU) |
Center differential lock switching is prohibited. | Indicator light blinks | Nothing |
| L4F switching control
(Switching to L4F is prohibited and the operation is performed with L4L when VSC is malfunctioning.) |
1.
4 wheel drive control ECU (4WD control ECU) 2.
Brake actuator assembly (skid control ECU) |
L4F switching is prohibited | Indicator light blinks | Nothing |
| Control performed during low temperatures
(Changes the value of the electric current applied to the ACT according to the temperature.) |
1.
4 wheel drive control ECU (4WD control ECU) 2.
ECM, Air conditioning amplifier |
Changes to the temperature used for ACT temperature correction control calculations. | Nothing | Nothing |
| Specialized control during wheel speed failure
(When there is a wheel speed failure, switching is permitted only when specified conditions are met (the wheel speed malfunction is 1 wheel or more and 3 wheels or less, the brake is applied, the engine speed is low, and all normal wheel speeds are low.)) |
1.
4 wheel drive control ECU (4WD control ECU) 2.
ECM, Brake actuator assembly (skid control ECU) |
If the wheel speed malfunction is 1 wheel or more and 3 wheels or less, only when the wheel speed failure specified conditions are met, switching is permitted. When 4 wheels are malfunctioning, switching is prohibited (the wheel speed failure specialized control does not operate). | Indicator light blinks | Nothing |
| Vehicle speed threshold limitation
(Determines whether the temperature is low or normal and changes the vehicle speed at which shifting from to 2 to 4 is prohibited.) |
1.
4 wheel drive control ECU (4WD control ECU) 2.
Air conditioning amplifier |
Uses the threshold value for low temperatures. | Nothing | Nothing |
| Indicator and buzzer signal output
(Outputs a signal indicating the state of the indicators and buzzers, which represent the actuator position and switching status.) |
1.
4 wheel drive control ECU (4WD control ECU) 2.
- |
The signal cannot be transmitted. Therefore, the signal is not updated. | Nothing | Nothing |
| Cruise control cancel signal output
(Outputs a cruise control cancel signal when center differential switching is not completed even though 5 seconds or more have elapsed from the start of switching.) |
1.
4 wheel drive control ECU (4WD control ECU) 2.
- |
The signal cannot be transmitted. Therefore, the signal is not updated. | Nothing | Nothing |
| L4 state signal output
(Outputs a signal when switching to the L4 position is finished.) |
1.
4 wheel drive control ECU (4WD control ECU) 2.
- |
The signal cannot be transmitted. Therefore, the signal is not updated. | Nothing | Nothing |
| 4WD state signal output
(The ADDSW state is output.) |
1.
4 wheel drive control ECU (4WD control ECU) 2.
- |
The signal cannot be transmitted. Therefore, the signal is not updated. | Nothing | Nothing |
| T/FN state signal output
(The NPSW state is output.) |
1.
4 wheel drive control ECU (4WD control ECU) 2.
- |
The signal cannot be transmitted. Therefore, the signal is not updated. | Nothing | Nothing |
| Motor Operation Signal Output
(Outputs the state of the actuator.) |
1.
4 wheel drive control ECU (4WD control ECU) 2.
- |
The signal cannot be transmitted. Therefore, the signal is not updated. | Nothing | Nothing |
| Electrical load control
(Performs idle up according to electrical load, etc.) |
1.
ECM 2.
Main body ECU (cowl side junction block LH), Air conditioning amplifier |
Idle up according to the electrical load is not performed. | Nothing | Nothing |
| Air conditioning-linked control
(Performs idle up according to the compressor load, and performs air conditioning cut control.) |
1.
ECM 2.
Air conditioning amplifier |
Air conditioning-linked control does not operate. | Nothing | Nothing |
| Charging control
(Performs idle up according to charging requests.) |
1.
ECM 2.
Main body ECU (cowl side junction block LH), Air conditioning amplifier |
Idle up according to charging requests is not performed. | Nothing | Nothing |
| Integrated control (VSC) (non drive force demand)
(Calculates the driver requested torque based on accelerator pedal operation.) |
1.
ECM 2.
Brake actuator assembly (skid control ECU), Steering angle sensor |
Integrated control is not performed. | Nothing | Nothing |
| ECT indicator in meter
(Shift position, switch, mode, etc.) |
1.
ECM 2.
Main body ECU (cowl side junction block LH), Combination meter assembly |
Indicators do not turn on. | Nothing | Nothing |
| AI-SHIFT control
(Controls the A/T in order to improve engine braking power and acceleration feeling.) |
1.
ECM 2.
Brake actuator assembly (skid control ECU) |
AI-SHIFT control does not operate. | Nothing | Nothing |
| Coast downshift
(Changes the coast down shift point according to the air conditioning load.) Heater requested upshift delay (Performs heater requested upshift delay.) |
1.
ECM 2.
Air conditioning amplifier |
Coast downshift does not operate. | Nothing | Nothing |
| Cruise control
(Adjusts the engine throttle valve opening amount automatically to control the vehicle.) |
1.
ECM 2.
Brake actuator assembly (skid control ECU), Combination meter assembly, Distance control ECU assembly |
Cruise control does not operate. | Nothing | ·
U0100 ·
U0122 ·
U0123 ·
U0126 ·
U1101 |
| ABS control
(Monitors for tire slippage and performs fluid pressure control to prevent the wheels from locking up in order to maintain vehicle stability and vehicle body deceleration.) |
1.
Brake actuator assembly (skid control ECU) 2.
4 wheel drive control ECU (4WD control ECU) |
The ABS does not operate. | ABS warning light turns on. | ·
U0073 ·
U0100 ·
U0126 |
| MSR control
(Prevents the tires from slipping due to engine drag torque by increasing engine torque.) |
1.
Brake actuator assembly (skid control ECU) 2.
ECM, Steering angle sensor, 4 wheel drive control ECU (4WD control ECU) |
MSR does not operate. | Light turns on. | U0100 |
| TCS control
(Prevents excessive tire slippage due to engine torque by decreasing engine torque and increasing pressure to the brakes.) |
1.
Brake actuator assembly (skid control ECU) 2.
ECM, Steering angle sensor, 4 wheel drive control ECU (4WD control ECU) |
TCS does not operate. | Light turns on. | U0114 |
| VSC control
(Reduces excess yaw by increasing brake pressure, and induces necessary yaw by increasing brake pressure and reducing engine torque.) |
1.
Brake actuator assembly (skid control ECU) 2.
ECM, Steering angle sensor, 4 wheel drive control ECU (4WD control ECU) |
VSC does not operate. | Light turns on. | Nothing |
| Manual mirror adjustment control
(Adjusts the outer mirrors according to the auto mirror switch operation.) |
1.
Outer mirror control ECU assembly 2.
Main body ECU (cowl side junction block LH) |
Manual control is stopped. | Nothing | Nothing |
| Mirror position memorization control
(Memorizes the current mirror position.) |
1.
Outer mirror control ECU assembly 2.
Front power seat switch LH (power seat control ECU), Main body ECU (cowl side junction block LH) |
Memorization control is prohibited. | Nothing | Nothing |
| Mirror position recall control
(Recalls the memorized position according to the recall command from the seat ECU.) |
1.
Outer mirror control ECU assembly 2.
Front power seat switch LH (power seat control ECU) |
Recall control is prohibited. | Nothing | Nothing |
| Outer mirror retraction control
(Retracts the outer mirrors.) |
1.
Outer mirror control ECU assembly 2.
Main body ECU (cowl side junction block LH) |
Retraction control is prohibited. | Nothing | Nothing |
| Reverse-linked control
(Tilts the mirrors down so that the area around the rear tires is visible when driving the vehicle in reverse.) |
1.
Outer mirror control ECU assembly 2.
Main body ECU (cowl side junction block LH) |
Reverse-linked operation is stopped. | Nothing | Nothing |
| Active Height Control Suspension
(System adjusts damping force based on vehicle conditions and can also adjust the vehicle height.) |
1.
Suspension control ECU 2.
Main body ECU (cowl side junction block LH), ECM, Brake actuator assembly (skid control ECU), Steering angle sensor |
Damping Force Control
(When a vehicle speed of 30 km/h (18 mph) or more is detected, control continues to operate. Below this speed, the actuators hold the damping force at the fail-safe level, which is the same level as when the vehicle is stopped. (Except for malfunctioning wheel)) Height Control System (Height control maintains the vehicle height at the normal level.) |
Light turns on. | ·
U0100 ·
U0122 ·
U0124 ·
U0126 ·
U0140 |
| Steering sensor
(Detects the steering wheel angle.) |
1.
Steering angle sensor 2.
Brake actuator assembly (skid control ECU) |
Periodically sends STR1S01 (STS0=1) every 12 ms. | Light turns on | Nothing |
| Auto away/return control
(Controls the auto away/return operation according to the SKSW and IG signals. Prohibits auto away/return control.) |
1.
Multiplex tilt and telescopic ECU 2.
Main body ECU (cowl side junction block LH), Combination meter assembly, Bus buffer ECU |
Auto away/return control does not operate. | Nothing | ·
B2621 ·
B2624 |
| Memorization/recall control
(Controls the steering wheel position memorization and recall for the seat position memory.) |
1.
Multiplex tilt and telescopic ECU 2.
Front power seat switch LH (power seat control ECU) |
Memorization/recall control does not operate. | Nothing | B2621 |
| TC DTC output service
(While TC = ON is being received from the engine, a DTC is output in response to the request from the combination meter assembly.) |
1.
Combination meter assembly 2.
ECM, Center airbag sensor assembly |
The TC service is stopped. | Nothing | Nothing |
| Event data recorder
(Records conditions such as the vehicle speed, the amount the accelerator is depressed, and the shift lever position when the event data recorder recording conditions are met.) |
1.
Center airbag sensor assembly 2.
ECM, Steering angle sensor, Brake actuator assembly (skid control ECU) |
An invalid value is stored. | Nothing | Nothing |
| Airbag warning light control
(Sends information used for turning the airbag warning light on and off.) |
1.
Combination meter assembly 2.
Center airbag sensor assembly |
- | Nothing | Nothing |
| Collision detection signal
(Notifies the system of a collision in order to perform a fuel cut at the time when a vehicle collision occurs.) |
1.
ECM 2.
Center airbag sensor assembly |
- | Nothing | Nothing |
| Seat belt warning light control
(Sends information used for turning the airbag warning light on and off.) |
1.
Main body ECU (cowl side junction block LH), Combination meter assembly 2.
Center airbag sensor assembly |
- | Nothing | Nothing |
| Warning control
(Displays various warnings in the combination meter according to illumination requests from various ECUs.) |
1.
Combination meter assembly 2.
Main body ECU (cowl side junction block LH), ECM, Brake actuator assembly (skid control ECU), Center airbag sensor assembly, 4 wheel drive control ECU (4WD control ECU), Suspension control ECU, Power steering ECU assembly |
The current status is maintained until the ignition switch is turned off, or various warnings illuminate. | Light turns on. | U0100 |
| Buzzer control
(Sounds various buzzers in the combination meter according to sounding requests from various ECUs.) |
1.
Combination meter assembly 2.
Main body ECU (cowl side junction block LH), ECM, Brake actuator assembly (skid control ECU), Center airbag sensor assembly, 4 wheel drive control ECU (4WD control ECU) |
The buzzers do not sound. | Nothing | Nothing |
| Meter Information Output 1
(Sends vehicle speed signals, tail cancel signals and signals indicating the temperature units.) |
1.
Combination meter assembly 2.
- |
- | Nothing | Nothing |
| Meter Information Output 2
(Sends destination information signals, steering wheel signals, signals indicating odometer units and odometer information signals.) |
1.
Combination meter assembly 2.
- |
- | Nothing | Nothing |
| Meter Information Output 13
(Sends a signal indicating the amount of fuel remaining in the main fuel tank and a signal indicating the amount of fuel remaining in the sub fuel tank.) |
1.
Combination meter assembly 2.
- |
- | Nothing | Nothing |
| Meter Information Output 15
(Sends fuel sender gauge signals.) |
1.
Combination meter assembly 2.
- |
- | Nothing | Nothing |
| Telltale
(Controls indicator illumination and blinking according to CAN signals.) |
1.
Combination meter assembly 2.
Main body ECU (cowl side junction block LH), ECM, Brake actuator assembly (skid control ECU), Center airbag sensor assembly, Suspension control ECU, Power steering ECU assembly |
Control is performed using information from the last signal received or indicators are illuminated. | Nothing | U0129 |
| Speedometer
(Controls the speedometer according to vehicle speed signals.) |
1.
Combination meter assembly 2.
Brake actuator assembly (skid control ECU) |
The speedometer displays 0 km/h (0 mph). | Nothing | U0129 |
| ODO/TRIP meter
(Indicates the driven distance in the combination meter according to the vehicle speed pulse signal summation value.) |
1.
Combination meter assembly 2.
Brake actuator assembly (skid control ECU) |
The calculation stops and the last displayed value remains. | Nothing | U0129 |
| Tachometer
(Controls the tachometer according to engine speed signals.) |
1.
Combination meter assembly 2.
ECM |
The tachometer displays 0 rpm. | Nothing | U0100 |
| Engine coolant temperature gauge
(Controls the gauge according to the engine coolant temperature signal.) |
1.
Combination meter assembly 2.
ECM |
The temperature gauge needle is at the middle of the "C" mark or below. | Nothing | Nothing |
| Fuel gauge
(Receives the starter signal and drives the indicator needle.) |
1.
Combination meter assembly 2.
ECM |
Controlled as "ST-OFF".
Controlled as "0 km/h (0 mph)". |
Nothing | Nothing |
| Oil pressure gauge
(Performs a start operation according to the engine speed signal.) |
1.
Combination meter assembly 2.
ECM |
Control is performed with the engine speed set to 0 rpm. | Nothing | U0100 |
| Transmission fluid temperature gauge
(Controls the gauge according to the transmission fluid signals.) |
1.
Combination meter assembly 2.
ECM |
The pointer needle is at the center of the "C" mark or below. | Nothing | Nothing |
| Gear position display
(Displays gear position according to the gear position signal and transmission temperature range signal.) |
1.
Combination meter assembly 2.
ECM |
The gear position display turns off.
SMDE=0 |
Nothing | Nothing |
| Combination Meter display (CRUISE INFORMATION display)
(Displays vehicle status on the Combination Meter based on status of each CAN signal.) |
1.
Combination meter assembly 2.
ECM, Brake actuator assembly (skid control ECU) |
Control is performed using the last signal received. | Nothing | Nothing |
| Multi-display
(Displays vehicle information through the multi-display based on the status of the BSD module state signal [BSD display processing].) |
1.
Combination meter assembly 2.
Blind spot monitor sensor RH |
Control is performed using the last signal received. | Nothing | Nothing |
| DTC Transmission
(Sends DTC polling signals to ECUs which transmit DTCs.) |
1.
Combination meter assembly 2.
- |
- | Nothing | Nothing |
| Alarm control
(Sounds various warnings.) |
1.
Main body ECU (cowl side junction block LH) 2.
Power back door unit assembly (power back door ECU), ECM, Bus buffer ECU |
The warnings do not operate. | Nothing | ·
U0199 ·
U0208 ·
U0230 ·
U1002 ·
U1115 |
| Door lock control
(Locks/unlocks the doors.) |
1.
Main body ECU (cowl side junction block LH) 2.
ECM, Combination meter assembly, Center airbag sensor assembly, Bus buffer ECU |
The vehicle speed auto-lock control does not operate. | Nothing | ·
U0199 ·
U0208 ·
U0230 ·
U1002 ·
U1115 |
| Illumination control
(Performs illumination control.) |
1.
Main body ECU (cowl side junction block LH) 2.
Bus buffer ECU |
KLEG is maintained. | Nothing | ·
U0199 ·
U0208 ·
U0230 ·
U1002 ·
U1115 |
| Power window control
(Performs key off power window control.) |
1.
Main body ECU (cowl side junction block LH) 2.
Bus buffer ECU |
KLEG is maintained. | Nothing | ·
U0199 ·
U0208 ·
U0230 ·
U1002 ·
U1115 |
| Light control
(Controls the display dimming and daytime running lights.) |
1.
Main body ECU (cowl side junction block LH) 2.
ECM, Center airbag sensor assembly |
Daytime running light control is not performed. | Nothing | ·
U0199 ·
U0208 ·
U0230 ·
U1002 ·
U1115 |
| Back door control
(Back Door Opener) |
1.
Main body ECU (cowl side junction block LH) 2.
Power back door unit assembly (power back door ECU), Combination meter assembly |
Power Back Door Buzzer does not sound.
Power Back Door Hazard Warning Lights do not operate. One Motion Power Back Door does not operate. Back Door Opener control is prohibited. |
Nothing | ·
U0199 ·
U0208 ·
U0230 ·
U1002 ·
U1115 |
| Wireless
(Controls the wireless lock/unlock functions.) |
1.
Main body ECU (cowl side junction block LH) 2.
Bus buffer ECU |
KLEG is maintained. | Nothing | ·
U0199 ·
U0208 ·
U0230 ·
U1002 ·
U1115 |
| Option control
(Controls optional wireless lock, answer-back optional illumination, alarm warning requests and dome light warning requests.) |
1.
Main body ECU (cowl side junction block LH) 2.
Bus buffer ECU |
·
Optional wireless lock control does not operate. ·
Answer-back control for optional illumination does not operate. ·
Alarm warning request control does not operate. ·
Dome light warning request control does not operate. |
Nothing | ·
U0199 ·
U0208 ·
U0230 ·
U1002 ·
U1115 |
| Lock control
(Sends a door lock request signal.) |
1.
Bus buffer ECU 2.
Main body ECU (cowl side junction block LH) |
Lock control is not performed. | Nothing | Nothing |
| Air conditioning control
(Requests air conditioning control by sending DFON and ACON signals.) |
1.
Bus buffer ECU 2.
- |
Air conditioning control is not performed. | Nothing | Nothing |
| Hazard answer-back control
(Requests hazard blinking through the HZRD bit.) |
1.
Bus buffer ECU 2.
Main body ECU (cowl side junction block LH) |
Hazard answer-back control is not performed. | Nothing | Nothing |