Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM
RM27L0U _57 Power Source / Network _049335 NETWORKING _0235802 CAN COMMUNICATION SYSTEM J

NETWORKING  CAN COMMUNICATION SYSTEM  Suspension Control ECU Communication Stop Mode  


DESCRIPTION

Detection Item Symptom Trouble Area
Suspension Control ECU Communication Stop Mode Either condition is met:
·

"Suspension Control (Air Suspension)" is not displayed on the "Bus Check" screen.

·

"Suspension Control ECU Communication Stop Mode" in "DTC Communication Table" applies.


·

Power source or inside of suspension control ECU

·

Suspension control ECU CAN branch wire or connector

·

Suspension control ECU



For vehicles with an air suspension system.


WIRING DIAGRAM

C243207E01
5.819,0.946 6.399,1.088 0.580,0.142 10 CANH 5.819,1.386 6.399,1.528 0.580,0.142 10 CANL 5.819,2.303 6.176,2.445 0.357,0.142 10 B 5.819,2.943 6.176,3.085 0.357,0.142 10 IG 2.601,2.303 3.380,2.445 0.779,0.142 10 from Battery 2.148,2.943 3.376,3.085 1.228,0.142 10 from IG No.1 Relay 5.819,3.584 6.176,3.726 0.357,0.142 10 GND 5.819,4.225 6.176,4.367 0.357,0.142 10 GND 1.935,0.831 2.514,0.973 0.580,0.142 10 6 1.935,1.271 2.514,1.413 0.580,0.142 10 12 0.835,1.775 1.414,1.917 0.580,0.142 10 O42 0.835,1.926 2.432,2.068 1.597,0.142 10 No. 4 Junction Connector 5.41,0.946 5.691,1.088 0.281,0.142 10 O16 5.41,1.386 5.697,1.528 0.287,0.142 10 O16 5.505,0.754 5.603,0.896 0.098,0.142 10 7 5.505,1.193 5.605,1.335 0.100,0.142 10 8 5.41,0.946 5.691,1.088 0.281,0.142 10 O16 5.41,1.386 5.697,1.528 0.287,0.142 10 O16 5.505,0.754 5.603,0.896 0.098,0.142 10 7 5.505,1.193 5.605,1.335 0.100,0.142 10 8 5.41,2.309 5.691,2.451 0.281,0.142 10 O16 5.505,2.116 5.603,2.258 0.098,0.142 10 3 5.41,2.943 5.697,3.085 0.287,0.142 10 O16 5.505,2.751 5.605,2.893 0.100,0.142 10 1 5.41,3.584 5.697,3.726 0.287,0.142 10 O16 5.505,3.392 5.605,3.534 0.100,0.142 10 5 5.41,4.225 5.697,4.367 0.287,0.142 10 O18 5.466,4.033 5.639,4.175 0.173,0.142 10 10 4.227,2.81 4.993,2.952 0.766,0.142 10 AIR SUS IG 4.139,2.148 5.079,2.290 0.940,0.142 10 AIR SUS NO.2 5.441,4.853 7.016,4.995 1.575,0.142 10 Suspension Control ECU

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


HINT:

Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.


PROCEDURE

1.PRECAUTION
NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).



NEXT

2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
a.

Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the CAN main wire and the CAN branch wire.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.


NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).




NEXT

3.CHECK FOR OPEN IN CAN BUS WIRE (SUSPENSION CONTROL ECU CAN BRANCH WIRE)
3.CHECK FOR OPEN IN CAN BUS WIRE (SUSPENSION CONTROL ECU CAN BRANCH WIRE)
a.
U153871E01
1.06,1.462 0.866,1.634 0.866,1.634 0.769,1.634 false 0.939,1.989 1.044,1.989 1.044,1.989 1.195,1.462 false 0.077,0.049 0.255,0.189 0.178,0.140 10 *a 0.256,1.55 0.673,1.691 0.417,0.140 10 CANH 0.423,1.909 0.840,2.049 0.417,0.140 10 CANL 2.717,1.235 2.997,1.375 0.280,0.140 10 O16

Disconnect the O16 suspension control ECU connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
O16-7 (CANH) - O16-8 (CANL) Ignition switch off 54 to 69 Ω


Text in Illustration
*a Front view of wire harness connector
(to Suspension Control ECU)



OK

4.CHECK HARNESS AND CONNECTOR (SUSPENSION CONTROL ECU - BATTERY AND BODY GROUND)

NG

REPAIR OR REPLACE SUSPENSION CONTROL ECU CAN BRANCH WIRE OR CONNECTOR (CANH, CANL)

4.CHECK HARNESS AND CONNECTOR (SUSPENSION CONTROL ECU - BATTERY AND BODY GROUND)
a.
U153872E02
2.333,2.365 2.531,2.188 2.531,2.188 2.625,2.188 true 2.083,0.896 2.427,1.188 2.427,1.188 2.521,1.188 true 1.156,0.792 0.969,0.615 0.969,0.615 0.875,0.615 true 1.646,0.865 0.979,1.344 0.979,1.344 0.844,1.344 true 0.073,0 0.25,0.135 0.177,0.135 10 false *a 2.667,2.104 3.167,2.344 0.5,0.24 10 false GND 0.656,0.521 0.927,0.708 0.271,0.188 10 false IG 2.677,0.698 3.01,0.896 0.333,0.198 10 false O16 0.698,1.271 0.875,1.406 0.177,0.135 10 false B 2.583,1.115 3.083,1.333 0.5,0.219 10 false GND 0.479,2.51 0.875,2.719 0.396,0.208 10 false O18

Connect the cable to the negative (-) battery terminal.

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).



b.

Disconnect the O18 suspension control ECU connector.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
O16-3 (B) - Body ground Always 11 to 14 V
O16-1 (IG) - Body ground Ignition switch ON 11 to 14 V



d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
O16-5 (GND) - Body ground Always Below 1 Ω
O18-10 (GND) - Body ground Always Below 1 Ω



Text in Illustration
*a Front view of wire harness connector
(to Suspension Control ECU)


OK

REPLACE SUSPENSION CONTROL ECU

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR