Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM
RM27L0U _57 Power Source / Network _049335 NETWORKING _0235802 CAN COMMUNICATION SYSTEM J

NETWORKING  CAN COMMUNICATION SYSTEM  4WD Control ECU Communication Stop Mode  


DESCRIPTION

Detection Item Symptom Trouble Area
4WD Control ECU Communication Stop Mode Either condition is met:
·

"Four Wheel Drive Control" is not displayed on the "Bus Check" screen.

·

"4WD Control ECU Communication Stop Mode" in "DTC Communication Table" applies.


·

Power source or inside of 4 wheel drive control ECU (4WD control ECU)

·

4 wheel drive control ECU (4WD control ECU) CAN branch wire or connector

·

4 wheel drive control ECU (4WD control ECU)



Fro vehicles with an 4WD.


WIRING DIAGRAM

C245788E02
0.84,1.648 2.513,1.789 1.673,0.141 10 No. 2 Junction Connector 5.894,0.657 6.411,0.793 0.517,0.136 10 CANH 5.894,1.09 6.411,1.227 0.517,0.136 10 CANL 5.894,2.258 6.411,2.394 0.517,0.136 10 IG 5.894,3.052 6.411,3.188 0.517,0.136 10 GND 4.37,2.082 4.709,2.239 0.339,0.157 10 4WD 1.436,2.248 2.736,2.390 1.300,0.142 10 from IG No.1 Relay 5.266,4.008 6.992,4.335 1.726,0.327 10 4 Wheel Drive Control ECU (4WD Control ECU) 0.84,1.506 1.366,1.645 0.525,0.139 10 H115 1.958,0.53 2.091,0.708 0.132,0.177 10 2 1.958,0.982 2.174,1.160 0.216,0.177 10 13 5.466,0.446 5.640,0.582 0.174,0.136 10 19 5.466,0.878 5.640,1.020 0.174,0.142 10 20 5.419,0.651 5.686,0.801 0.267,0.150 10 A28 5.419,1.085 5.686,1.235 0.267,0.150 10 A28 5.505,2.045 5.602,2.182 0.098,0.136 10 3 5.505,2.846 5.602,2.988 0.098,0.142 10 4 5.419,2.25 5.686,2.400 0.267,0.150 10 A29 5.419,3.053 5.686,3.203 0.267,0.150 10 A29

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


HINT:

Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.


PROCEDURE

1.PRECAUTION
NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).



NEXT

2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
a.

Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the CAN main wire and the CAN branch wire.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.


NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).




NEXT

3.CHECK FOR OPEN IN CAN BUS WIRE (4WD CONTROL ECU CAN BRANCH WIRE)
3.CHECK FOR OPEN IN CAN BUS WIRE (4WD CONTROL ECU CAN BRANCH WIRE)
a.
U153824E01
1.02,1.14 0.808,1.545 0.808,1.545 0.69,1.545 false 0.659,0.898 0.719,0.898 0.719,0.898 0.928,1.115 false 0.178,1.468 0.597,1.610 0.420,0.142 10 CANH 0.178,0.818 0.597,0.960 0.420,0.142 10 CANL 0.08,0.05 0.500,0.192 0.420,0.142 10 *a 2.86,1.106 3.131,1.248 0.272,0.142 10 A28

Disconnect the A28 4 wheel drive control ECU (4WD control ECU) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
A28-19 (CANH) - A28-20 (CANL) Ignition switch off 54 to 69 Ω


Text in Illustration
*a Rear view of wire harness connector
(to 4 Wheel Drive Control ECU [4WD Control ECU])



OK

4.CHECK HARNESS AND CONNECTOR (4WD CONTROL ECU - BATTERY AND BODY GROUND)

NG

REPAIR OR REPLACE 4WD CONTROL ECU CAN BRANCH WIRE OR CONNECTOR (CANH, CANL)

4.CHECK HARNESS AND CONNECTOR (4WD CONTROL ECU - BATTERY AND BODY GROUND)
a.
U153893E01
1.117,0.796 1.229,0.796 1.229,0.796 1.508,1.123 false 1.362,1.23 1.143,1.522 1.143,1.522 1.018,1.522 false 0.077,0.053 0.386,0.261 0.309,0.208 10 *a 0.877,0.721 1.317,0.860 0.441,0.139 10 IG 0.593,1.447 1.034,1.586 0.441,0.139 10 GND 2.492,1.171 2.763,1.309 0.270,0.139 10 A29

Connect the cable to the negative (-) battery terminal.

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).



b.

Disconnect the A29 4 wheel drive control ECU (4WD control ECU) connector.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
A29-3 (IG) - Body ground Ignition switch ON 11 to 14 V



d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A29-4 (GND) - Body ground Always Below 1 Ω



Text in Illustration
*a Rear view of wire harness connector
(to 4 Wheel Drive Control ECU [4WD Control ECU])


OK

REPLACE 4 WHEEL DRIVE CONTROL ECU (4WD CONTROL ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR