Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM
RM27L0U _57 Power Source / Network _049335 NETWORKING _0235802 CAN COMMUNICATION SYSTEM J

NETWORKING  CAN COMMUNICATION SYSTEM  Main Body ECU Communication Stop Mode  


DESCRIPTION

Detection Item Symptom Trouble Area
Main Body ECU Communication Stop Mode Either condition is met:
·

"Main Body" is not displayed on the "Bus Check" screen.

·

"Main Body ECU Communication Stop Mode" in "DTC Communication Table" applies.


·

Power source or inside of main body ECU (cowl side junction block LH)

·

Main body ECU (cowl side junction block LH) CAN branch wire or connector

·

Main body ECU (cowl side junction block LH)



WIRING DIAGRAM

C158948E10
0.698,2.438 2.375,2.656 1.677,0.219 10 false No. 1 Junction Connector 5.5,1.427 5.813,1.635 0.313,0.208 10 false H2 5.813,1.417 6.333,1.604 0.521,0.188 10 false CANH 5.823,1.865 6.344,2.052 0.521,0.188 10 false CANL 5.563,1.208 5.75,1.385 0.188,0.177 10 false 5 5.552,1.667 5.781,1.844 0.229,0.177 10 false 6 5.854,2.563 6.375,2.75 0.521,0.188 10 false BECU 5.854,3.24 6.375,3.427 0.521,0.188 10 false ALTB 5.844,5.521 6.365,5.708 0.521,0.188 10 false GND1 5.604,3.115 5.792,3.292 0.188,0.177 10 false 6 5.604,5.344 5.833,5.521 0.229,0.177 10 false 5 5.542,3.771 5.771,3.948 0.229,0.177 10 false 22 4.26,3.365 4.792,3.573 0.531,0.208 10 false DR/LCK 4.385,4.042 4.729,4.25 0.344,0.208 10 false ACC 2.229,4.573 2.844,4.927 0.615,0.354 10 false from Battery 3.865,5.021 5.146,5.177 1.281,0.156 10 false from IG1 No.3 Relay 5.865,3.896 6.385,4.083 0.521,0.188 10 false ACC 5.573,4.479 5.802,4.656 0.229,0.177 10 false 15 4.688,4.74 5.625,4.927 0.938,0.188 10 false ECU-IG No.2 5.698,6.208 6.917,6.417 1.219,0.208 10 false Main Body ECU 0.698,2.292 1.063,2.448 0.365,0.156 10 false H119 1.938,1.281 2.073,1.458 0.135,0.177 10 false 6 1.938,1.74 2.135,1.917 0.198,0.177 10 false 17 5.865,4.604 6.385,4.792 0.521,0.188 10 false IG 5.49,1.875 5.802,2.083 0.313,0.208 10 false H2 5.063,2.573 5.375,2.781 0.313,0.208 10 false DB 3.292,3.229 3.604,3.438 0.313,0.208 10 false DA 3.302,5.531 3.615,5.74 0.313,0.208 10 false DD 5.563,2.458 5.75,2.635 0.188,0.177 10 false 26 3.615,2.698 4.177,2.906 0.563,0.208 10 false ECU-B1 3.323,5.271 3.552,5.448 0.229,0.177 10 false 62 5.073,2.385 5.302,2.563 0.229,0.177 10 false 13 3.354,2.99 3.583,3.167 0.229,0.177 10 false 1 3.281,4.542 4.365,4.74 1.083,0.198 10 false from ACC Relay

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


HINT:

Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.


PROCEDURE

1.PRECAUTION
NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).



NEXT

2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
a.

Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the CAN main wire and the CAN branch wire.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.


NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).




NEXT

3.CHECK FOR OPEN IN CAN BUS WIRE (MAIN BODY ECU CAN BRANCH WIRE)
3.CHECK FOR OPEN IN CAN BUS WIRE (MAIN BODY ECU CAN BRANCH WIRE)
a.
U153837E01
1.404,1.351 1.138,1.617 1.138,1.617 1,1.617 false 1.249,1.973 1.356,1.973 1.356,1.973 1.537,1.351 false 0.495,1.541 0.916,1.678 0.422,0.137 10 CANH 0.74,1.896 1.161,2.032 0.422,0.137 10 CANL 2.501,1.178 2.700,1.315 0.199,0.137 10 H2 0.067,0.048 0.267,0.185 0.199,0.137 10 *a

Disconnect the H2 main body ECU (cowl side junction block LH) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
H2-5 (CANH) - H2-6 (CANL) Ignition switch off 54 to 69 Ω


Text in Illustration
*a Front view of wire harness connector
(to Main Body ECU [Cowl Side Junction Block LH])



OK

4.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - BATTERY AND BODY GROUND)

NG

REPAIR OR REPLACE MAIN BODY ECU CAN BRANCH WIRE OR CONNECTOR (CANH, CANL)

4.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - BATTERY AND BODY GROUND)
a.

Connect the cable to the negative (-) battery terminal.

U153978E01
0.227,0.14 0.464,0.363 0.237,0.223 10 *a 1.043,0.796 1.255,0.940 0.211,0.144 10 DA 0.268,2.441 0.726,2.594 0.458,0.152 10 ALTB 2.899,2.231 3.336,2.390 0.437,0.159 10 BECU 5.527,2.306 5.947,2.469 0.420,0.163 10 GND1 1.038,2.043 0.753,2.505 0.753,2.505 0.62,2.505 false 3.189,1.064 3.401,1.208 0.211,0.144 10 DB 5.632,1.064 5.850,1.208 0.218,0.144 10 DD 2.467,1.828 2.752,2.291 2.752,2.291 2.885,2.291 false 5.243,1.693 5.381,2.37 5.381,2.37 5.514,2.37 false

Text in Illustration
*a Front view of wire harness connector
(to Main Body ECU [Cowl Side Junction Block LH])
- -

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).



b.

Disconnect the DA, DB and DD main body ECU (cowl side junction block LH) connectors.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
DA-1 (ALTB) - Body ground Always 11 to 14 V
DB-13 (BECU) - Body ground Always 11 to 14 V



d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
DD-62 (GND1) - Body ground Always Below 1 Ω




OK

REPLACE MAIN BODY ECU (COWL SIDE JUNCTION BLOCK LH)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR