Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM
RM27L0U _57 Power Source / Network _049335 NETWORKING _0235802 CAN COMMUNICATION SYSTEM C

NETWORKING  CAN COMMUNICATION SYSTEM  U0230  Lost Communication with Rear Gate Module  


DESCRIPTION

DTC Code DTC Detection Condition Trouble Area
U0230 There is no communication from the power back door unit assembly (power back door ECU).
·

Power source or inside of power back door unit assembly (power back door ECU)

·

Power back door unit assembly (power back door ECU) CAN branch wire or connector

·

Power back door unit assembly (power back door ECU)



For vehicles with an power back door system.


WIRING DIAGRAM

C245287E02
0.636,1.667 2.308,1.814 1.673,0.146 10 No. 4 Junction Connector 0.641,1.522 1.036,1.667 0.395,0.145 10 O42 1.925,0.577 2.058,0.755 0.132,0.177 10 1 1.92,1.029 2.101,1.207 0.181,0.177 10 7 5.837,2.361 6.354,2.498 0.517,0.137 10 B 5.608,0.609 5.704,0.748 0.096,0.139 10 6 5.608,1.051 5.704,1.190 0.096,0.139 10 5 5.528,2.259 5.703,2.398 0.175,0.139 10 12 5.521,4.241 5.703,4.380 0.183,0.139 10 11 3.999,2.175 4.304,2.313 0.305,0.138 10 PBD 3.748,3.535 4.602,3.673 0.854,0.138 10 ECU-IG No.2 5.837,3.68 6.234,3.816 0.397,0.136 10 IG 5.608,3.582 5.704,3.721 0.096,0.139 10 8 5.837,2.937 6.251,3.074 0.414,0.136 10 ECUB 5.528,2.85 5.703,2.989 0.175,0.139 10 10 3.886,2.812 4.416,2.955 0.530,0.143 10 ECU-B1 1.87,2.362 2.648,2.498 0.778,0.136 10 from Battery 1.351,3.678 2.643,3.819 1.292,0.141 10 from IG1 No.3 Relay 5.837,4.335 6.354,4.474 0.517,0.139 10 GND 5.837,0.692 6.354,0.829 0.517,0.136 10 CANP 5.837,1.132 6.354,1.268 0.517,0.136 10 CANN 5.096,5.096 7.122,5.400 2.026,0.304 10 Power Back Door Unit Assembly (Power Back Door ECU) 5.096,4.944 5.613,5.084 0.517,0.139 10 O30

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


HINT:

Operating the ignition switch, any other switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.


PROCEDURE

1.PRECAUTION
NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).



NEXT

2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
a.

Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the CAN main wire and CAN branch wire.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.


NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).




NEXT

3.CHECK FOR OPEN IN CAN BUS WIRE (POWER BACK DOOR ECU CAN BRANCH WIRE)
3.CHECK FOR OPEN IN CAN BUS WIRE (POWER BACK DOOR ECU CAN BRANCH WIRE)
a.
U153881E02
1.656,1.344 1.865,1.823 1.865,1.823 1.979,1.823 true 1.5,1.344 1.292,1.823 1.292,1.823 1.177,1.823 true 0.115,0.083 0.5,0.302 0.385,0.219 10 false *a 0.729,1.74 1.26,1.917 0.531,0.177 10 false CANN 2.042,1.76 2.615,1.969 0.573,0.208 10 false CANP 1.583,0.5 1.99,0.698 0.406,0.198 10 false O30

Disconnect the O30 power back door unit assembly (power back door ECU) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
O30-6 (CANP) - O30-5 (CANN) Ignition switch off 54 to 69 Ω


Text in Illustration
*a Front view of wire harness connector
(to Power Back Door Unit Assembly [Power Back Door ECU])



OK

4.CHECK HARNESS AND CONNECTOR (POWER BACK DOOR ECU - BATTERY AND BODY GROUND)

NG

REPAIR OR REPLACE POWER BACK DOOR ECU CAN BRANCH WIRE OR CONNECTOR (CANP, CANN)

4.CHECK HARNESS AND CONNECTOR (POWER BACK DOOR ECU - BATTERY AND BODY GROUND)
a.
U153882E02
2.219,1.302 2.469,1.854 2.469,1.854 2.583,1.854 true 1.896,1.333 1.708,1.854 1.708,1.854 1.594,1.854 true 2.677,1.177 2.896,1 2.896,1 3.01,1 true 2.427,1.177 2.792,0.708 2.792,0.708 2.906,0.708 true 0.073,0.052 0.24,0.208 0.167,0.156 10 false *a 1.375,1.771 1.625,1.969 0.25,0.198 10 false IG 2.594,1.771 3.177,2 0.583,0.229 10 false ECUB 3.031,0.927 3.26,1.167 0.229,0.24 10 false B 2.927,0.635 3.365,0.865 0.438,0.229 10 false GND 1.594,0.5 1.99,0.729 0.396,0.229 10 false O30

Connect the cable to the negative (-) battery terminal.

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).



b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
O30-12 (B) - Body ground Always 11 to 14 V
O30-10 (ECUB) - Body ground Always 11 to 14 V
O30-8 (IG) - Body ground Ignition switch ON 11 to 14 V



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
O30-11 (GND) - Body ground Always Below 1 Ω



Text in Illustration
*a Front view of wire harness connector
(to Power Back Door Unit Assembly [Power Back Door ECU])


OK

REPLACE POWER BACK DOOR UNIT ASSEMBLY (POWER BACK DOOR ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR