Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM
RM27L0U _57 Power Source / Network _049335 NETWORKING _0235802 CAN COMMUNICATION SYSTEM J

NETWORKING  CAN COMMUNICATION SYSTEM  Bus Buffer ECU Communication Stop Mode  


DESCRIPTION

Detection Item Symptom Trouble Area
Bus Buffer ECU Communication Stop Mode Either condition is met:
·

"Accessory Gateway" is not displayed on the "Bus Check" screen.

·

"Bus Buffer ECU Communication Stop Mode" in "DTC Communication Table" applies.


·

Bus buffer ECU CAB branch wire or connector

·

Bus buffer ECU



For vehicles with an bus buffer ECU.


WIRING DIAGRAM

C245793E02
5.689,0.773 6.206,0.957 0.517,0.184 10 CAN+ 5.689,1.198 6.206,1.382 0.517,0.184 10 CAN- 5.443,0.643 5.631,0.820 0.188,0.177 10 3 5.446,1.095 5.676,1.272 0.230,0.177 10 2 0.64,1.773 2.313,1.995 1.673,0.223 10 No. 2 Junction Connector 0.64,1.638 1.021,1.790 0.380,0.152 10 H115 5.551,1.773 6.578,1.995 1.027,0.223 10 Bus Buffer ECU 5.551,1.638 5.931,1.790 0.380,0.152 10 H66 1.785,0.646 1.917,0.823 0.132,0.177 10 5 1.785,1.098 1.963,1.275 0.179,0.177 10 16

CAUTION / NOTICE / HINT

HINT:

Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.


PROCEDURE

1.PRECAUTION
NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).



NEXT

2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
a.

Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the CAN main wire and the CAN branch wire.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.


NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).




NEXT

3.CHECK FOR OPEN IN CAN BUS WIRE (BUS BUFFER ECU CAN BRANCH WIRE)
3.CHECK FOR OPEN IN CAN BUS WIRE (BUS BUFFER ECU CAN BRANCH WIRE)
a.
U153828E01
0.636,0.826 1.034,0.966 0.398,0.140 10 CAN+ 0.801,1.651 1.168,1.789 0.368,0.137 10 CAN- 2.544,1.107 2.817,1.245 0.273,0.138 10 H66 0.063,0.062 0.333,0.228 0.270,0.166 10 *a 1.395,1.157 1.192,0.912 1.192,0.912 1.117,0.912 false 1.262,1.723 1.336,1.723 1.336,1.723 1.745,1.256 false

Disconnect the H66 bus buffer ECU connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
H66-3 (CAN+) - H66-2 (CAN-) Ignition switch off 54 to 69 Ω


Text in Illustration
*a Rear view of wire harness connector
(to Bus Buffer ECU)



OK

REPLACE BUS BUFFER ECU

NG

REPAIR OR REPLACE BUS BUFFER ECU CAN BRANCH WIRE OR CONNECTOR (CAN+, CAN-)