Home › Power Source / Network › NETWORKING › LIN COMMUNICATION SYSTEM
RM27L0U _57 Power Source / Network _049335 NETWORKING _0235803 LIN COMMUNICATION SYSTEM U

NETWORKING  LIN COMMUNICATION SYSTEM  TERMINALS OF ECU  


CHECK MAIN BODY ECU


B443326E01
0.969,3.552 1.365,3.781 0.396,0.229 2.99,3.531 3.385,3.76 0.396,0.229 5.51,3.521 5.906,3.75 0.396,0.229 1.469,5.094 1.865,5.323 0.396,0.229 4.292,5.104 4.688,5.333 0.396,0.229 5.969,5.042 6.365,5.271 0.396,0.229 0.938,6.948 1.333,7.177 0.396,0.229 3.427,6.917 3.823,7.146 0.396,0.229 5.927,6.917 6.323,7.146 0.396,0.229 1.052,3.583 1.365,3.781 0.313,0.198 10 false DA 3.073,3.573 3.385,3.771 0.313,0.198 10 false DB 5.635,3.573 5.948,3.771 0.313,0.198 10 false DC 1.573,5.125 1.885,5.323 0.313,0.198 10 false DD 4.406,5.146 4.719,5.344 0.313,0.198 10 false DE 6.083,5.083 6.396,5.281 0.313,0.198 10 false H1 1.052,6.979 1.365,7.177 0.313,0.198 10 false H2 3.563,6.958 3.875,7.156 0.313,0.198 10 false H3 6.031,6.979 6.344,7.177 0.313,0.198 10 false H4

a.

Disconnect the DA, DB, DD and H2 main body ECU connectors.


b.

Measure the resistance and voltage according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
H2-10 (LIN2) - Body ground V - Body ground LIN communication line Ignition switch ON Pulse generation
DA-1 (ALTB) - DD-62 (GND1) B - W-B Battery power supply Always 11 to 14 V
DB-13 (BECU) - DD-62 (GND1) GR - W-B Battery power supply Always 11 to 14 V
DD-62 (GND1) - Body ground W-B - Body ground Ground Always Below 1 Ω

HINT:

If the result is not as specified, there may be a malfunction on the wire harness side.



c.

Reconnect the main body ECU connectors.



CHECK POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY


U154040E01
3.959,1.793 4.169,1.974 0.210,0.181 10 M2 4.29,0.073 6.657,0.619 2.367,0.546 10 Front view of wire harness connector: (to Power Window Regulator Master Switch Assembly) 4.875,2.433 5.031,2.614 0.156,0.181 10 B 4.389,1.615 4.545,1.796 0.156,0.181 10 E 5.167,1.879 4.968,2.428 false 5.555,1.872 5.355,2.422 false 5.698,1.872 5.898,2.422 false 4.54,1.696 4.888,1.829 false 0.541,0.09 3.064,0.661 2.523,0.571 10 Component without harness connected: (Power Window Regulator Master Switch Assembly) 5.249,2.433 5.559,2.614 0.310,0.181 10 LIN1 5.761,2.433 6.071,2.614 0.310,0.181 10 LIN2

a.

Disconnect the M2 power window regulator master switch assembly connector.


b.

Measure the resistance and voltage according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
M2-1 (E) - Body ground W-B - Body ground Ground Always Below 1 Ω
M2-3 (B) - M2-1 (E) L - W-B Battery power supply Always 11 to 14 V
M2-6 (LIN1) - Body ground L - Body ground LIN communication line Ignition switch ON Pulse generation
M2-7 (LIN2) - Body ground W - Body ground LIN communication line Ignition switch ON Pulse generation

HINT:

If the result is not as specified, there may be a malfunction on the wire harness side.



c.

Reconnect the power window regulator master switch assembly connector.



CHECK FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH


U154041E02
5.604,1.875 6.188,1.677 true 5.51,2.198 6.104,2.396 true 5.313,1.875 4.719,1.677 true 4.417,2.073 4.625,2.25 0.208,0.177 10 false M3 4.063,0.198 6.625,0.719 2.563,0.521 10 false Front view of wire harness connector: (to Front Power Window Regulator Motor Assembly LH) 6.198,1.604 6.354,1.781 0.156,0.177 10 false B 4.385,1.615 4.708,1.792 0.323,0.177 10 false GND 6.167,2.323 6.396,2.5 0.229,0.177 10 false LIN 0.563,0.208 3.083,0.781 2.521,0.573 10 false Component without harness connected: (Front Power Window Regulator Motor Assembly LH)

a.

Disconnect the M3 front power window regulator motor assembly LH connector.


b.

Measure the resistance and voltage according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
M3-1 (GND) - Body ground W-B - Body ground Ground Always Below 1 Ω
M3-2 (B) - M3-1(GND) G - W-B Battery power supply Always 11 to 14 V
M3-9 (LIN) - Body ground W - Body ground LIN communication line Ignition switch ON Pulse generation

HINT:

If the result is not as specified, there may be a malfunction on the wire harness side.



c.

Reconnect the front power window regulator motor assembly LH connector.



CHECK FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY RH


U154042E02
5.604,1.875 6.188,1.677 true 5.49,2.198 6.083,2.396 true 5.313,1.875 4.719,1.677 true 4.438,2.083 4.604,2.26 0.167,0.177 10 false L3 4.063,0.198 6.625,0.719 2.563,0.521 10 false Front view of wire harness connector: (to Front Power Window Regulator Motor Assembly RH) 6.198,1.604 6.354,1.781 0.156,0.177 10 false B 4.385,1.615 4.708,1.792 0.323,0.177 10 false GND 6.156,2.333 6.385,2.51 0.229,0.177 10 false LIN 0.563,0.208 3.083,0.781 2.521,0.573 10 false Component without harness connected: (Front Power Window Regulator Motor Assembly RH)

a.

Disconnect the L3 front power window regulator motor assembly RH connector.


b.

Measure the resistance and voltage according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
L3-1 (GND) - Body ground W-B - Body ground Ground Always Below 1 Ω
L3-2 (B) - L3-1 (GND) V - W-B Battery power supply Always 11 to 14 V
L3-9 (LIN) - Body ground L - Body ground LIN communication line Ignition switch ON Pulse generation

HINT:

If the result is not as specified, there may be a malfunction on the wire harness side.



c.

Reconnect the front power window regulator motor assembly RH connector.



CHECK SLIDING ROOF DRIVE GEAR SUB-ASSEMBLY


U154043E02
5.844,1.958 5.938,2.344 true 5.458,1.979 5.365,2.333 true 5.698,1.677 6.292,1.469 true 4.188,1.781 4.385,1.958 0.198,0.177 10 false U3 4.094,0.094 6.656,0.448 2.563,0.354 10 false Front view of wire harness connector: (to Sliding Roof Drive Gear Sub-Assembly) 5.885,2.354 6.042,2.531 0.156,0.177 10 false B 5.292,2.354 5.448,2.531 0.156,0.177 10 false E 6.333,1.406 6.729,1.583 0.396,0.177 10 false MPX1 0.521,0.125 3.042,0.49 2.521,0.365 10 false Component without harness connected: (Sliding Roof Drive Gear Sub-Assembly)

a.

Disconnect the U3 sliding roof drive gear sub-assembly connector.


b.

Measure the resistance and voltage according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
U3-3 (MPX1) - Body ground P - Body ground LIN communication line Ignition switch ON Pulse generation
U3-8 (E) - Body ground W-B - Body ground Ground Always Below 1 Ω
U3-10 (B) - U3-8 (E) L - W-B Battery power supply Always 11 to 14 V

HINT:

If the result is not as specified, there may be a malfunction on the wire harness side.



c.

Reconnect the sliding roof drive gear sub-assembly connector.



CHECK BACK DOOR ECU


U154044E01
4.664,1.698 4.851,1.879 0.187,0.181 10 V2 4.537,0.165 6.978,0.518 2.441,0.353 10 Front view of wire harness connector: (to Back Door ECU) 4.787,1.393 5.097,1.574 0.310,0.181 10 BDR 5.118,1.465 5.454,1.64 false 4.565,1.998 4.968,2.179 0.403,0.181 10 BECU 4.985,2.069 5.408,1.843 false 6.601,1.398 6.927,1.579 0.326,0.181 10 GND 6.565,1.469 6.229,1.644 false 6.629,1.945 7.024,2.126 0.395,0.181 10 MPX1 6.593,2.016 6.257,1.884 false 0.992,0.165 3.515,0.528 2.523,0.363 10 Component without harness connected: (Back Door ECU)

a.

Disconnect the V2 back door ECU connector.


b.

Measure the resistance and voltage according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
V2-1 (BDR) - V2-6 (GND) SB - W-B Battery power supply Always 11 to 14 V
V2-6 (GND) - Body ground W-B - Body ground Ground Always Below 1 Ω
V2-7 (BECU) - V2-6(GND) GR - W-B Battery power supply Always 11 to 14 V
V2-16 (MPX1) - Body ground Y - Body ground LIN communication line Ignition switch ON Pulse generation

HINT:

If the result is not as specified, there may be a malfunction on the wire harness side.



c.

Reconnect the back door ECU connector.