Home › Power Source / Network › NETWORKING › LIN COMMUNICATION SYSTEM
RM27L0U _57 Power Source / Network _049335 NETWORKING _0235803 LIN COMMUNICATION SYSTEM C

NETWORKING  LIN COMMUNICATION SYSTEM  B1206  P/W Master Switch Communication Stop  


DESCRIPTION

This DTC is stored when LIN communication between the power window regulator master switch assembly and main body ECU stops for 10 seconds or more.

DTC Code DTC Detection Condition Trouble Area
B1206 No communication between the master switch and main body ECU for 10 seconds or more.
·

Power window regulator master switch assembly

·

Main body ECU

·

Harness or connector



WIRING DIAGRAM

B173719E82
0.917,4.74 2.563,4.938 1.646,0.198 10 false : LIN Communication Line 0.604,3.875 1.458,4.073 0.854,0.198 10 false from Battery 1.656,4.073 2.615,4.271 0.958,0.198 10 false POWER No. 3 3.427,4.333 3.656,4.51 0.229,0.177 10 false M2 3.375,3.75 3.573,3.927 0.198,0.177 10 false 3 3.375,2.99 3.594,3.167 0.219,0.177 10 false 6 3.313,1.146 3.5,1.323 0.188,0.177 10 false 10 3.563,3.104 4,3.281 0.438,0.177 10 false LIN1 3.563,1.26 4,1.438 0.438,0.177 10 false LIN2 4.458,3.104 4.594,3.281 0.135,0.177 10 false E 4.656,2.99 4.844,3.167 0.188,0.177 10 false 1 3.563,3.844 4,4.021 0.438,0.177 10 false B 3.438,4.5 5.542,4.917 2.104,0.417 10 false Power Window Regulator Master Switch Assembly 3.49,1.917 3.76,2.094 0.271,0.177 10 false H2 3.5,2.094 5.146,2.646 1.646,0.552 10 false Main Body ECU

CAUTION / NOTICE / HINT

NOTICE:

When using the Techstream with the ignition switch off to troubleshoot:

Connect the Techstream to the vehicle, and turn a courtesy switch on and off at 1.5 second intervals until communication between the Techstream and vehicle begins.


HINT:

DTC B2325 is stored when the communication between the master switch and main body ECU stops.


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - MASTER SWITCH)
a.
U154028E02
2.229,1.656 2.688,1.49 true 2.146,3.938 2.802,3.51 false 0.552,1.385 0.75,1.563 0.198,0.177 10 false H2 0.51,3.875 0.719,4.052 0.208,0.177 10 false M2 0.271,0.094 2.635,0.49 2.365,0.396 10 false Front view of wire harness connector: (to Main Body ECU) 0.26,2.167 2.625,2.708 2.365,0.542 10 false Front view of wire harness connector: (to Power Window Regulator Master Switch Assembly) 2.76,1.396 3.073,1.573 0.313,0.177 10 false LIN2 2.844,3.406 3.156,3.583 0.313,0.177 10 false LIN1

Disconnect the H2 main body ECU connector.


b.

Disconnect the M2 power window regulator master switch assembly connector.


c.

Measure the resistance and voltage according to the value(s) in the tables below.

Standard Resistance:
Tester Connection Condition Specified Condition
H2-10 (LIN2) - M2-6 (LIN1) Always Below 1 Ω
H2-10 (LIN2) or M2-6 (LIN1) - Body ground Always 10 kΩ or higher


Standard Voltage:
Tester Connection Condition Specified Condition
M2-6 (LIN1) - Body ground Always Below 1 V



d.

Reconnect the main body ECU connector.


e.

Reconnect the power window regulator master switch assembly connector.



OK

2.CHECK POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY (MASTER SWITCH - BATTERY AND BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY (MASTER SWITCH - BATTERY AND BODY GROUND)
a.
U154029E02
1.729,1.75 2.802,1.344 true 1,1.5 1.417,1.74 true 0.344,1.635 0.552,1.813 0.208,0.177 10 false M2 0.083,0 2.521,0.542 2.438,0.542 10 false Front view of wire harness connector: (to Power Window Regulator Master Switch Assembly) 2.865,1.25 3.021,1.427 0.156,0.177 10 false B 0.823,1.396 0.979,1.573 0.156,0.177 10 false E

Disconnect the M2 power window regulator master switch assembly connector.


b.

Measure the resistance and voltage according to the value(s) in the tables below.

Standard Resistance:
Tester Connection Condition Specified Condition
M2-1 (E) - Body ground Always Below 1 Ω


Standard Voltage:
Tester Connection Condition Specified Condition
M2-3 (B) - Body ground Always 11 to 14 V



c.

Reconnect the power window regulator master switch assembly connector.



OK

3.REPLACE POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.REPLACE POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY
a.

Temporarily replace the power window regulator master switch assembly with a new or normally functioning one (See page Vehicle Exterior>WINDOW / GLASS>POWER WINDOW MASTER SWITCH>REMOVAL).




NEXT

4.CHECK FOR DTC
4.CHECK FOR DTC
a.

Recheck for DTCs (See page Power Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>DTC CHECK / CLEAR).

Result
Result Proceed to
DTC B1206 is not output A
DTC B1206 is output B



A

END (MASTER SWITCH IS DEFECTIVE)

B

REPLACE MAIN BODY ECU