Home › Power Source / Network › NETWORKING › LIN COMMUNICATION SYSTEM
RM27L0U _57 Power Source / Network _049335 NETWORKING _0235803 LIN COMMUNICATION SYSTEM C

NETWORKING  LIN COMMUNICATION SYSTEM  B2322  Front Passenger Side Door ECU Communication Stop  


DESCRIPTION

This DTC is stored when LIN communication between the front power window regulator motor assembly RH and main body ECU stops for 10 seconds or more.

DTC Code DTC Detection Condition Trouble Area
B2322 No communication between the front power window regulator motor assembly RH and main body ECU for 10 seconds or more.
·

Front power window regulator motor assembly RH

·

Main body ECU

·

Harness or connector



WIRING DIAGRAM

B173719E84
0.917,4.708 1.583,4.906 0.667,0.198 10 false : LIN Line 0.594,3.885 1.448,4.083 0.854,0.198 10 false from Battery 1.615,4.042 2.573,4.24 0.958,0.198 10 false POWER NO. 4 3.458,4.344 3.688,4.521 0.229,0.177 10 false L3 3.375,3.75 3.573,3.927 0.198,0.177 10 false 2 3.354,2.99 3.51,3.167 0.156,0.177 10 false 9 3.313,1.146 3.5,1.323 0.188,0.177 10 false 10 3.563,3.104 4,3.281 0.438,0.177 10 false LIN 3.563,1.26 4,1.438 0.438,0.177 10 false LIN2 4.24,3.104 4.604,3.281 0.365,0.177 10 false GND 4.708,2.99 4.844,3.167 0.135,0.177 10 false 1 3.563,3.844 4,4.021 0.438,0.177 10 false B 3.469,4.49 5.5,4.896 2.031,0.406 10 false Front Power Window Regulator Motor Assembly RH 3.49,1.917 3.76,2.094 0.271,0.177 10 false H2 3.5,2.063 5.375,2.302 1.875,0.24 10 false Main Body ECU

CAUTION / NOTICE / HINT

NOTICE:

When using the Techstream with the ignition switch off to troubleshoot:

Connect the Techstream to the vehicle, and turn a courtesy switch on and off at 1.5 second intervals until communication between the Techstream and vehicle begins.


HINT:

DTC B2325 is stored when the communication between the front power window regulator motor assembly RH and main body ECU stops.


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - REGULATOR MOTOR RH)
a.
U154033E01
0.514,1.406 0.709,1.587 0.195,0.181 10 H2 0.514,3.808 0.724,3.990 0.210,0.181 10 L3 0.264,0.07 2.630,0.467 2.367,0.397 10 Front view of wire harness connector: (to Main Body ECU) 0.128,2.206 2.688,2.725 2.560,0.519 10 Front view of wire harness connector: (to Front Power Window Regulator Motor Assembly RH) 2.772,1.421 3.082,1.602 0.310,0.181 10 LIN2 2.268,1.693 2.734,1.53 false 2.802,3.98 3.036,4.161 0.233,0.181 10 LIN 2.038,4.308 2.764,4.065 false

Disconnect the H2 main body ECU connector.


b.

Disconnect the L3 front power window regulator motor assembly RH connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H2-10 (LIN2) - L3-9 (LIN) Always Below 1 Ω



d.

Reconnect the main body ECU connector.


e.

Reconnect the front power window regulator motor assembly RH connector.



OK

2.CHECK FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY RH (REGULATOR MOTOR RH - BATTERY AND BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY RH (REGULATOR MOTOR RH - BATTERY AND BODY GROUND)
a.
U154035E02
2.073,2.281 2.802,2.042 true 1.708,2.281 0.979,2.042 true 0.656,2.604 0.865,2.781 0.208,0.177 10 false L3 0.125,0.146 2.458,0.76 2.333,0.615 10 false Front view of wire harness connector: (to Front Power Window Regulator Motor Assembly RH) 2.844,1.979 3,2.156 0.156,0.177 10 false B 0.604,1.969 0.927,2.146 0.323,0.177 10 false GND

Disconnect the L3 front power window regulator motor assembly RH connector.


b.

Measure the resistance and voltage according to the value(s) in the tables below.

Standard Resistance:
Tester Connection Condition Specified Condition
L3-1 (GND) - Body ground Always Below 1 Ω


Standard Voltage:
Tester Connection Condition Specified Condition
L3-2 (B) - Body ground Always 11 to 14 V



c.

Reconnect the front power window regulator motor assembly RH connector.



OK

3.REPLACE FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY RH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.REPLACE FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY RH
a.

Temporarily replace the front power window regulator motor assembly RH with a new or normally functioning one (See page Vehicle Exterior>WINDOW / GLASS>POWER WINDOW REGULATOR MOTOR>REMOVAL).




NEXT

4.CHECK FOR DTC
4.CHECK FOR DTC
a.

Recheck for DTCs (See page Power Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>DTC CHECK / CLEAR).

Result
Result Proceed to
DTC B2322 is not output A
DTC B2322 is output B



A

END (FRONT POWER WINDOW REGULATOR MOTOR RH IS DEFECTIVE)

B

REPLACE MAIN BODY ECU