Home › Vehicle Interior › DOOR LOCK › FRONT DOOR LOCK
RM27L0U _58 Vehicle Interior _049336 DOOR LOCK _0235808 FRONT DOOR LOCK G

DOOR LOCK  FRONT DOOR LOCK  INSPECTION  


PROCEDURE

Hide 69040A 1.INSPECT FRONT DOOR LOCK ASSEMBLY LH

a.

Check the door lock motor.

i.

Apply battery voltage to the door lock motor and check operation of the door lock motor.

B443308E01
4.406,1.344 4.74,1.344 true 4.76,1.885 4.979,1.583 true 5.146,1.563 5.385,1.875 true 5.396,1.375 5.729,1.375 true 2.125,2.365 2.646,2.563 0.521,0.198 10 false Unlock 1.573,2.49 1.948,2.688 0.375,0.198 10 false Lock 3.906,0.333 6.344,0.729 2.438,0.396 10 false Component without harness connected: (Front Door Lock LH) 4.563,1.896 5,2.073 0.438,0.177 10 false LSSR 5.427,1.833 5.594,2.021 0.167,0.188 10 false E 4.313,1.281 4.479,1.469 0.167,0.188 10 false L 5.771,1.302 6,1.469 0.229,0.167 10 false UL

OK:
Measurement Condition Specified Condition
Battery positive (+) → Terminal 4 (L)
Battery negative (-) → Terminal 1 (UL)
Lock
Battery positive (+) → Terminal 1 (UL)
Battery negative (-) → Terminal 4 (L)
Unlock


If the result is not as specified, replace the door lock assembly.




b.

Check the door lock position switch.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
7 (E) - 8 (LSSR) Unlock Below 1 Ω
Lock 10 kΩ or higher


If the result is not as specified, replace the door lock assembly.




c.

Check the door lock and unlock switch.

i.

Measure the resistance according to the value(s) in the table below.

B443035E02
4.396,1.75 4.823,1.75 true 4.896,2.135 5,1.802 true 5.417,2.135 5.271,1.771 true 2.281,0.281 2.792,0.469 0.51,0.188 10 false Unlock 2.458,1.146 2.969,1.333 0.51,0.188 10 false Lock 3.875,0.531 6.333,0.865 2.458,0.333 10 false Component without harness connected: (Front Door Lock LH) 4.188,1.688 4.438,1.896 0.25,0.208 10 false UL 4.823,2.146 5.073,2.354 0.25,0.208 10 false L 5.417,2.156 5.667,2.365 0.25,0.208 10 false E

Standard Resistance:
Tester Connection Switch Condition Specified Condition
7 (E) - 10 (UL) Locked 10 kΩ or higher
7 (E) - 10 (UL) Unlocked Below 1 Ω
7 (E) - 9 (L) Locked 10 kΩ or higher
7 (E) - 9 (L) Unlocked Below 1 Ω


If the result is not as specified, replace the door lock assembly.




Hide 69030A 2.INSPECT FRONT DOOR LOCK ASSEMBLY RH

a.

Check the door lock motor.

i.

Apply battery voltage to the door lock motor and check operation of the door lock motor.

B443036E01
4.906,2.104 5.104,1.781 true 5.26,1.781 5.448,2.094 true 4.854,1.583 4.49,1.583 true 5.875,1.583 5.51,1.583 true 0.76,2.104 1.25,2.313 0.49,0.208 10 false Unlock 2.063,2.385 2.552,2.594 0.49,0.208 10 false Lock 3.969,0.51 6.406,0.885 2.438,0.375 10 false Component without harness connected: (Front Door Lock RH) 4.385,1.521 4.542,1.719 0.156,0.198 10 false L 5.927,1.51 6.167,1.708 0.24,0.198 10 false UL 4.833,2.115 5.073,2.313 0.24,0.198 10 false E 5.406,2.104 5.833,2.313 0.427,0.208 10 false LSSR

OK:
Measurement Condition Specified Condition
Battery positive (+) → Terminal 4 (L)
Battery negative (-) → Terminal 1 (UL)
Lock
Battery positive (+) → Terminal 1 (UL)
Battery negative (-) → Terminal 4 (L)
Unlock


If the result is not as specified, replace the door lock assembly.




b.

Check the door lock position switch.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
7 (LSSR) - 8 (E) Unlock Below 1 Ω
Lock 10 kΩ or higher


If the result is not as specified, replace the door lock assembly.