Home › Vehicle Interior › DOOR LOCK › REAR DOOR LOCK
RM27L0U _58 Vehicle Interior _049336 DOOR LOCK _0235809 REAR DOOR LOCK G

DOOR LOCK  REAR DOOR LOCK  INSPECTION  


PROCEDURE

Hide 69340 1.INSPECT REAR DOOR LOCK ASSEMBLY LH

a.

Check the door lock motor.

i.

Apply battery voltage to the door lock and check operation of the door lock.

B443309E01
4.375,1.281 4.781,1.281 true 5.448,1.292 5.854,1.292 true 5.427,1.813 5.302,1.51 true 4.75,1.813 4.917,1.51 true 1.063,2.281 1.427,2.458 0.365,0.177 10 false Lock 3.917,0.333 6.344,0.698 2.427,0.365 10 false Component without harness connected: (Rear Door Lock LH) 1.646,2.375 2.115,2.563 0.469,0.188 10 false Unlock 4.281,1.219 4.438,1.417 0.156,0.198 10 false L 5.896,1.208 6.094,1.406 0.198,0.198 10 false UL 4.677,1.833 4.833,2.031 0.156,0.198 10 false E 5.333,1.823 5.74,2.031 0.406,0.208 10 false LSSR

OK:
Measurement Condition Specified Condition
Battery positive (+) → Terminal 4 (L)
Battery negative (-) → Terminal 1 (UL)
Lock
Battery positive (+) → Terminal 1 (UL)
Battery negative (-) → Terminal 4 (L)
Unlock


If the result is not as specified, replace the door lock assembly.




b.

Check the door lock position switch.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
6 (LSSR) - 9 (E) Unlock Below 1 Ω
Lock 10 kΩ or higher


If the result is not as specified, replace the door lock assembly.




Hide 69330 2.INSPECT REAR DOOR LOCK ASSEMBLY RH

a.

Check the door lock motor.

i.

Apply battery voltage to the door lock and check operation of the door lock.

B443310E01
4.479,1.479 4.938,1.479 true 5.594,1.5 6.052,1.5 true 5,2.021 5.063,1.719 true 5.469,1.708 5.531,2.021 true 2.313,2.292 2.927,2.49 0.615,0.198 10 false Lock 1.594,2.385 2.208,2.583 0.615,0.198 10 false Unlock 3.99,0.333 6.396,0.677 2.406,0.344 10 false Component without harness connected: (Rear Door Lock RH) 4.375,1.417 4.531,1.615 0.156,0.198 10 false L 6.094,1.427 6.313,1.625 0.219,0.198 10 false UL 4.938,2.042 5.094,2.24 0.156,0.198 10 false E 5.49,2.042 5.927,2.25 0.438,0.208 10 false LSSR

OK:
Measurement Condition Specified Condition
Battery positive (+) → Terminal 4 (L)
Battery negative (-) → Terminal 1 (UL)
Lock
Battery positive (+) → Terminal 1 (UL)
Battery negative (-) → Terminal 4 (L)
Unlock


If the result is not as specified, replace the door lock assembly.




b.

Check the door lock position switch.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
6 (LSSR) - 9 (E) Unlock Below 1 Ω
Lock 10 kΩ or higher


If the result is not as specified, replace the door lock assembly.