Home › Vehicle Interior › DOOR LOCK › BACK DOOR LOCK
RM27L0U _58 Vehicle Interior _049336 DOOR LOCK _0235812 BACK DOOR LOCK G

DOOR LOCK  BACK DOOR LOCK  INSPECTION  


PROCEDURE

Hide 69110A 1.INSPECT BACK DOOR LOCK (w/o Power Back Door)

a.

Check operation of the door lock motor.

B443311E01
4.781,1.583 5.146,1.771 true 5.375,1.771 5.76,1.583 true 5.385,1.969 5.76,1.969 true 4.792,1.969 5.135,1.969 true 2.323,2.115 2.823,2.313 0.5,0.198 10 false Unlock 2.344,0.573 2.75,0.771 0.406,0.198 10 false Lock 4.063,0.333 6.479,0.729 2.417,0.396 10 false Component without harness connected: (Back Door Lock) 5.813,1.5 6.24,1.698 0.427,0.198 10 false ACT- 4.385,1.5 4.813,1.698 0.427,0.198 10 false ACT+ 4.646,1.906 4.802,2.104 0.156,0.198 10 false E 5.813,1.896 5.969,2.094 0.156,0.198 10 false S

i.

Move the door lock to the lock position.


ii.

Apply the battery voltage to the door lock motor and check the operation of the door lock motor.

OK:
Measurement Condition Specified Condition
Battery positive (+) → 2 (ACT-)
Battery negative (-) → 1 (ACT+)
Unlocked


If the result is not specified, replace the back door lock.



b.

Check operation of the door courtesy switch.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
3 (E) - 4 (S) Locked 10 kΩ or higher
3 (E) - 4 (S) Unlocked Below 1 Ω


If the result is not specified, replace the back door lock.



Hide 69350 2.INSPECT BACK DOOR LOCK (w/ Power Back Door)

a.

Check operation of the door lock motor.

B192558E02
1.938,3.792 1.615,4.094 true 1.958,4.24 1.625,4.292 true 1.979,4.646 1.615,4.521 true 1.052,3.792 1.375,4.094 true 1.031,4.229 1.365,4.281 true 1,4.635 1.365,4.51 true 0.24,2.469 2.75,2.656 2.51,0.188 10 false Component without harness connected: 0.25,2.656 1.365,2.885 1.115,0.229 10 false (Back Door Lock) 1.99,3.698 2.344,3.896 0.354,0.198 10 false ACT- 0.646,3.719 1.052,3.875 0.406,0.156 10 false ACT+ 0.885,4.156 1.042,4.313 0.156,0.156 10 false E 2.01,4.167 2.354,4.333 0.344,0.167 10 false FSW 0.698,4.563 1.01,4.76 0.313,0.198 10 false CLS 2.031,4.583 2.177,4.729 0.146,0.146 10 false S 5.302,3.729 6,3.896 0.698,0.167 10 false Over-latch 5.323,3.958 5.938,4.135 0.615,0.177 10 false Full-latch 5.323,4.917 5.958,5.094 0.635,0.177 10 false Half-latch 4.906,5.469 5.635,5.635 0.729,0.167 10 false Open-latch 4.75,1.333 5.146,1.594 0.396,0.26 10 true Close 3.542,1.344 4.104,1.594 0.563,0.25 10 true Release

i.

Move the door lock to the lock position.


ii.

Apply the battery voltage to the door lock motor and check the operation of the door lock motor.

OK:
Measurement Condition Specified Condition
Battery positive (+) → Terminal 2 (ACT-)
Battery negative (-) → Terminal 1 (ACT+)
Latch turns to full-latch position
Battery positive (+) → Terminal 1 (ACT+)
Battery negative (-) → Terminal 2 (ACT-)
Latch turns to open-latch position


If the result is not specified, replace the back door lock.



b.

Check operation of the switch.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Latch Switch
Tester Connection Door Lock Latch Position Specified Condition
3 (E) - 5 (CLS) Over-latch Below 1 Ω
3 (E) - 5 (CLS) Open-latch 10 kΩ or higher
3 (E) - 5 (CLS) Full-latch 10 kΩ or higher
3 (E) - 5 (CLS) Half-latch 10 kΩ or higher

Sector Switch
Tester Connection Door Lock Latch Position Specified Condition
3 (E) - 4 (FSW) Open-latch Below 1 Ω
3 (E) - 4 (FSW) Over-latch 10 kΩ or higher
3 (E) - 4 (FSW) Full-latch 10 kΩ or higher
3 (E) - 4 (FSW) Half-latch 10 kΩ or higher

Back Door Courtesy Switch
Tester Connection Door Lock Latch Position Specified Condition
3 (E) - 6 (S) Open-latch Below 1 Ω
3 (E) - 6 (S) Half-latch Below 1 Ω
3 (E) - 6 (S) Full-latch 10 kΩ or higher
3 (E) - 6 (S) Over-latch 10 kΩ or higher


If the result is not specified, replace the back door lock.