Home › Vehicle Interior › DOOR LOCK › WIRELESS DOOR LOCK CONTROL SYSTEM
RM27L0U _58 Vehicle Interior _049336 DOOR LOCK _0235813 WIRELESS DOOR LOCK CONTROL SYSTEM J

DOOR LOCK  WIRELESS DOOR LOCK CONTROL SYSTEM  Only Wireless Control Function is Inoperative  


DESCRIPTION

The door control receiver receives signals from the transmitter and sends these signals to the main body ECU. The main body ECU then controls all doors by sending lock/unlock signals to each door, and sends hazard flasher relay signals to the turn signal flasher relay (hazard warning lights).

WIRING DIAGRAM

B176381E22
1.083,1.208 1.302,1.458 0.219,0.25 10 false +B 0.979,2 1.375,2.25 0.396,0.25 10 false RDA 0.979,2.823 1.375,3.073 0.396,0.25 10 false PRG 0.969,3.594 1.365,3.844 0.396,0.25 10 false GND 2.573,1.344 3.344,1.615 0.771,0.271 10 false ECU-B1 4.615,1.188 5.49,1.5 0.875,0.313 10 false from Battery 0.25,4.99 0.542,5.177 0.292,0.188 10 false O25 0.25,5.156 1.813,5.427 1.563,0.271 10 false Door Control Receiver 1.365,1.083 1.563,1.323 0.198,0.24 10 false 5 1.365,1.875 1.563,2.115 0.198,0.24 10 false 2 1.365,2.688 1.563,2.927 0.198,0.24 10 false 3 1.365,3.469 1.563,3.708 0.198,0.24 10 false 1 5.125,3.49 5.323,3.729 0.198,0.24 10 false 1 4.323,3.49 4.521,3.729 0.198,0.24 10 false 2 4.156,3.781 4.448,3.969 0.292,0.188 10 false H21 4.156,3.948 5.719,4.219 1.563,0.271 10 false Unlock Warning Switch 5.927,1.979 6.323,2.229 0.396,0.25 10 false RDA 5.927,2.792 6.323,3.042 0.396,0.25 10 false PRG 5.927,3.583 6.5,3.854 0.573,0.271 10 false KSW 5.625,1.99 5.948,2.198 0.323,0.208 10 false H3 5.615,2.802 5.938,3.01 0.323,0.208 10 false H3 5.625,3.583 5.906,3.729 0.281,0.146 10 false H1 5.844,4.979 6.927,5.292 1.083,0.313 10 false Main Body ECU 5.604,2.615 5.885,2.76 0.281,0.146 10 false 10 5.625,1.802 5.906,1.948 0.281,0.146 10 false 12 5.677,3.406 5.958,3.552 0.281,0.146 10 false 5

PROCEDURE

1.CHECK WIRELESS DOOR LOCK CONTROL FUNCTIONS
a.

Check the wireless door lock control system function (See page Vehicle Interior>DOOR LOCK>WIRELESS DOOR LOCK CONTROL SYSTEM>OPERATION CHECK).


Result
Result Proceed to
The wireless door LOCK/UNLOCK function does not operate with transmitter A
The power back door function does not operate with transmitter B


A

2.CHECK DOOR CONTROL TRANSMITTER

B

2.CHECK DOOR CONTROL TRANSMITTER
a.

When another registered door control transmitter is used, check that the wireless operates normally.

Result
Result Proceed to
Wireless door LOCK/UNLOCK function operates and door control transmitter that did not operate is electrical key transmitter A
Wireless door LOCK/UNLOCK function does not operate B



A

3.INSPECT TRANSMITTER BATTERY (VOLTAGE)

B

4.CHECK ROOM LIGHT ASSEMBLY
3.INSPECT TRANSMITTER BATTERY (VOLTAGE)
a.

Electrical key transmitter

i.
B178434

Remove the battery from the electrical key transmitter that does not operate. Attach a lead wire (0.6 mm (0.0236 in.) in diameter or less including wire sheath) with tape or equivalent to the negative terminal (See page Vehicle Interior>DOOR LOCK>TRANSMITTER BATTERY>REPLACEMENT).

NOTICE:

Do not wrap the lead wire around a terminal, wedge it between terminals, or solder it. A terminal may be deformed or damaged, and the battery will not be able to be installed correctly.



ii.

Carefully pull the lead wire out from the position shown in the illustration and install the previously removed transmitter battery.


iii.
B443305E01
1.531,4.292 1.438,4.292 1.438,4.292 1.198,2.906 false 0.219,3.833 0.531,4.01 0.313,0.177 10 false GND 1.573,4.208 3.042,4.406 1.469,0.198 10 false Measurement Potition

Using an oscilloscope, check the transmitter battery voltage waveform.

HINT:

Measure the transmitter battery voltage while pressing the LOCK or UNLOCK switch on the transmitter.


Standard Voltage:
Item Content
Tester Connection Battery positive (+) - Battery negative (-)
Tool Setting 0.5 V/DIV., 100 ms/DIV.
Condition Ignition switch OFF, all doors closed and lock switch pushed
Specified Condition 2.2 to 3.2 V (Refer to the waveform)





OK

REPLACE DOOR CONTROL TRANSMITTER

NG

REPLACE TRANSMITTER BATTERY

4.CHECK ROOM LIGHT ASSEMBLY
a.

Check that the room light illumination operates normally.

OK:

Room light operation normally.




OK

5.SWITCH TO SELF-DIAGNOSTIC MODE

NG

5.SWITCH TO SELF-DIAGNOSTIC MODE
a.
B110075E28
0.083,0.073 1.385,0.302 1.302,0.229 10 false Interior Light Output: 1.802,0.594 2.917,0.75 1.115,0.156 10 false T1: 0.25 seconds 1.802,0.875 2.823,1.031 1.021,0.156 10 false T2: 0.5 seconds 0.635,1.594 0.865,1.74 0.229,0.146 10 false ON 0.573,1.885 0.875,2.052 0.302,0.167 10 false OFF 1.51,2.354 1.698,2.5 0.188,0.146 10 false T1 2.01,2.354 2.208,2.5 0.198,0.146 10 false T2

Switch to self-diagnostic mode by operating the ignition key cylinder.

i.

Make sure the vehicle is in its initial condition. Then insert the key into the ignition key cylinder and remove it.


ii.

Within 5 seconds of removing the key, insert the key into the ignition key cylinder (ignition switch off). Then turn the ignition switch to ON and off.


iii.

Within 30 seconds of turning the ignition switch off, perform the following operation 9 times: turn the ignition switch to ON and then off.

NOTICE:

If the system cannot enter self-diagnostic mode, the system returns to normal mode.


HINT:
·

Turning the ignition switch to ON after the above operations have been completed ends self-diagnostic mode.

·

Do not lock or unlock doors during self-diagnostic mode.





b.

Check that the system has switched to self-diagnostic mode by checking the room light flash pattern.

OK:

Flash pattern is same as illustration.




OK

6.CHECK BY SELF DIAGNOSTIC MODE

NG

12.INSPECT UNLOCK WARNING SWITCH
6.CHECK BY SELF DIAGNOSTIC MODE
B123864E22
0.115,0.073 1.438,0.313 1.323,0.24 10 false Interior Light Output: 1.417,1.813 2.323,1.969 0.906,0.156 10 false Normal Wave: 1.333,0.854 1.531,1 0.198,0.146 10 false T1 1.792,0.844 1.99,1.01 0.198,0.167 10 false T2 0.594,1.24 0.854,1.385 0.26,0.146 10 false ON 0.583,1.615 0.885,1.771 0.302,0.156 10 false OFF 3.729,1.219 3.958,1.365 0.229,0.146 10 false ON 3.677,1.594 3.99,1.74 0.313,0.146 10 false OFF 4.479,0.75 5.802,0.927 1.323,0.177 10 false Wave being received 4.156,1.802 6.115,1.979 1.958,0.177 10 false Mismatched Recognition Code: 0.396,3.76 0.708,3.917 0.313,0.156 10 false OFF 1.104,3.917 2.458,4.104 1.354,0.188 10 false No Diagnosis Output: 4.813,3.438 5.917,3.594 1.104,0.156 10 false T1: 0.25 seconds 4.813,3.75 5.896,3.917 1.083,0.167 10 false T2: 0.50 seconds

a.

Inspect the diagnosis outputs when the door control transmitter switch is held down. The diagnosis outputs can be checked by the flash patterns of the room light.

Result
Result Proceed to
Unmatching recognition code is output A
Normal waves (light flash patterns) is output B
No diagnosis outputs C



A

7.REGISTER RECOGNITION CODE

B

REPLACE MAIN BODY ECU

C

8.CHECK DOOR CONTROL RECEIVER (RESPONSE)
7.REGISTER RECOGNITION CODE
a.

Check that the system can be switched to rewrite mode or add mode, and that a recognition code can be registered (See page Vehicle Interior>DOOR LOCK>WIRELESS DOOR LOCK CONTROL SYSTEM>REGISTRATION).

OK:

Recognition code can be registered.




OK

END

NG

15.REPLACE DOOR CONTROL TRANSMITTER
8.CHECK DOOR CONTROL RECEIVER (RESPONSE)
a.

Prepare the door control transmitter of another vehicle.


b.

Hold down the door control transmitter switch.


c.

Check that an unmatching recognition code is output.

OK:

Unmatching recognition code is output.




OK

REPLACE DOOR CONTROL TRANSMITTER

NG

9.REPLACE DOOR CONTROL RECEIVER
9.REPLACE DOOR CONTROL RECEIVER
a.

Temporarily replace the door lock control receiver with a new or normally functioning one (See page Vehicle Interior>DOOR LOCK>DOOR CONTROL RECEIVER>REMOVAL).



NEXT

10.REGISTER RECOGNITION CODE
10.REGISTER RECOGNITION CODE
a.

Perform the registration procedures (See page Vehicle Interior>DOOR LOCK>WIRELESS DOOR LOCK CONTROL SYSTEM>REGISTRATION).



NEXT

11.CHECK DOOR CONTROL RECEIVER (OPERATION)
11.CHECK DOOR CONTROL RECEIVER (OPERATION)
a.

Check that the doors can be locked and unlocked by using the transmitter LOCK and UNLOCK switches.

OK:

Doors can be locked and unlocked with transmitter.




OK

END (DOOR CONTROL RECEIVER IS DEFECTIVE)

NG

REPLACE MAIN BODY ECU

12.INSPECT UNLOCK WARNING SWITCH
a.
B164411E19
0.083,0.063 2.521,0.438 2.438,0.375 10 false Component without harness connected: (Unlock Warning Switch) 0.448,1 0.76,1.177 0.313,0.177 10 false Free 0.26,1.354 0.771,1.5 0.51,0.146 10 false Pushed

Remove the unlock warning switch (See page Vehicle Interior>DOOR LOCK>UNLOCK WARNING SWITCH>REMOVAL).


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
1 - 2 Free 10 kΩ or higher
Pushed Below 1 Ω



c.

Reconnect the unlock warning switch.



OK

13.CHECK HARNESS AND CONNECTOR (UNLOCK WARNING SWITCH - MAIN BODY ECU AND BODY GROUND)

NG

REPLACE UNLOCK WARNING SWITCH

13.CHECK HARNESS AND CONNECTOR (UNLOCK WARNING SWITCH - MAIN BODY ECU AND BODY GROUND)
B443306E01
0.729,1.365 1.083,1.563 0.354,0.198 0.604,3.844 0.958,4.042 0.354,0.198 1.729,4.042 2.104,4.25 2.104,4.25 2.229,4.25 true 0.781,1.375 1.115,1.563 0.333,0.188 10 false H21 0.698,3.854 1.031,4.042 0.333,0.188 10 false H1 2.271,4.167 2.635,4.354 0.365,0.188 10 false KSW 0.188,2.281 2.469,2.656 2.281,0.375 10 false Front view of wire harness connector: (to Main Body ECU) 0.167,0.115 2.438,0.49 2.271,0.375 10 false Front view of wire harness connector: (to Unlock Warning Switch)

a.

Disconnect the H21 unlock warning switch connector.


b.

Disconnect the H1 main body ECU connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H21-1 - H1-5 (KSW) Always Below 1 Ω
H21-2 - Body ground
H1-5 (KSW) or H21-1 - Body ground Always 10 kΩ or higher



d.

Reconnect the unlock warning switch connector.


e.

Reconnect the main body ECU connector



OK

14.INSPECT DOOR CONTROL RECEIVER (OUTPUT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

14.INSPECT DOOR CONTROL RECEIVER (OUTPUT)
a.
U153204E02
1.719,2.542 2.75,2.885 true 0.365,0.104 2.625,0.313 2.26,0.208 10 false Component with harness connected: 0.365,0.281 2.01,0.479 1.646,0.198 10 false (Door Control Receiver) 2.781,2.813 3.156,2.99 0.375,0.177 10 false RDA 0.667,1.344 1.042,1.521 0.375,0.177 10 false O25

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
O25-2 (RDA) - Body ground Transmitter switch not pressed → pressed (No key in ignition key cylinder, all doors closed) 11 to 14 V → Pulse generation




OK

REPLACE MAIN BODY ECU

NG

15.REPLACE DOOR CONTROL TRANSMITTER
15.REPLACE DOOR CONTROL TRANSMITTER
a.

Temporarily replace the door control transmitter module with a new or normally functioning one.



NEXT

16.REGISTER RECOGNITION CODE
16.REGISTER RECOGNITION CODE
a.

Perform the registration procedures (See page Vehicle Interior>DOOR LOCK>WIRELESS DOOR LOCK CONTROL SYSTEM>REGISTRATION).



NEXT

17.CHECK DOOR CONTROL TRANSMITTER MODULE
17.CHECK DOOR CONTROL TRANSMITTER MODULE
a.

Check that the doors can be locked and unlocked by using the transmitter LOCK and UNLOCK switches.

OK:

Doors can be locked and unlocked with transmitter.




OK

END (DOOR CONTROL TRANSMITTER MODULE IS DEFECTIVE)

NG

REPLACE DOOR CONTROL RECEIVER