Home › Vehicle Interior › DOOR LOCK › WIRELESS DOOR LOCK CONTROL SYSTEM
RM27L0U _58 Vehicle Interior _049336 DOOR LOCK _0235813 WIRELESS DOOR LOCK CONTROL SYSTEM C

DOOR LOCK  WIRELESS DOOR LOCK CONTROL SYSTEM  B1242  Wireless Door Lock Tuner Circuit Malfunction  


DESCRIPTION

The door control receiver receives signals from the transmitter and sends these signals to the main body ECU.

DTC No. DTC Detection Condition Trouble Area
B1242 In diagnostic mode, an applicable RDA signal cannot be received within 1 second after an PRG signal has been output from the main body ECU.
·

Wire harness or connector

·

Door control receiver

·

Main body ECU



WIRING DIAGRAM

B443304E01
1.167,2.656 2.031,2.844 0.865,0.188 10 false from Battery 2.25,2.813 2.771,2.99 0.521,0.177 10 false ECU-B1 2.74,3.281 4.115,3.479 1.375,0.198 10 false Door Control Receiver 2.729,3.125 3.073,3.302 0.344,0.177 10 false O25 2.708,2.552 2.844,2.74 0.135,0.188 10 false 5 2.708,1.667 2.844,1.854 0.135,0.188 10 false 1 3.813,1.667 3.948,1.854 0.135,0.188 10 false 2 3.813,2.542 3.948,2.729 0.135,0.188 10 false 3 5.146,2.552 5.323,2.74 0.177,0.188 10 false 10 5.406,3.625 5.656,3.802 0.25,0.177 10 false H3 5.146,1.677 5.323,1.865 0.177,0.188 10 false 12 5.396,3.781 6.458,3.969 1.063,0.188 10 false Main Body ECU 5.406,2.656 5.771,2.844 0.365,0.188 10 false PRG 5.406,1.771 5.771,1.958 0.365,0.188 10 false RDA 3.406,2.677 3.771,2.865 0.365,0.188 10 false PRG 3.417,1.792 3.781,1.979 0.365,0.188 10 false RDA 2.875,1.781 3.24,1.969 0.365,0.188 10 false GND 2.896,2.656 3.146,2.844 0.25,0.188 10 false +B

PROCEDURE

1.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - DOOR CONTROL RECEIVER)
a.
B443029E02
0.24,1.396 0.635,1.625 0.396,0.229 0.354,3.625 0.75,3.854 0.396,0.229 2.385,1.281 2.688,1.198 true 0.719,1.813 1.177,1.594 true 1.25,4.417 1.479,3.99 true 1.896,4.417 1.708,4 true 0.188,0.167 2.448,0.542 2.26,0.375 10 false Front view of wire harness connector: (to Main Body ECU) 0.208,2.5 2.469,2.875 2.26,0.375 10 false Front view of wire harness connector: (to Door Control Receiver) 0.365,1.427 0.573,1.604 0.208,0.177 10 false H3 0.427,3.656 0.76,3.833 0.333,0.177 10 false O25 2.75,1.115 3.208,1.313 0.458,0.198 10 false PRG 0.5,1.844 0.844,2.042 0.344,0.198 10 false RDA 0.917,4.354 1.375,4.552 0.458,0.198 10 false RDA 1.948,4.375 2.406,4.573 0.458,0.198 10 false PRG

Disconnect the H3 main body ECU connector and the O25 door control receiver connector.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H3-12 (RDA) - O25-2 (RDA) Always Below 1 Ω
H3-12 (RDA) - Body ground Always 10 kΩ or higher
H3-10 (PRG) - O25-3 (PRG) Always Below 1 Ω
H3-10 (PRG) - Body ground Always 10 kΩ or higher




b.

Reconnect the main body ECU connector and the door control receiver connector.



OK

2.CHECK HARNESS AND CONNECTOR (BATTERY, BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK HARNESS AND CONNECTOR (BATTERY, BODY GROUND)
a.

Disconnect the O25 door control receiver connector.


U153205E02
1.542,2.948 1.198,3.063 false 1.927,2.948 2.281,3.073 false 0.365,0.115 2.74,0.354 2.375,0.24 10 false Front view of wire harness connector: 0.344,0.292 2.063,0.656 1.719,0.365 10 false (to Door Control Receiver) 0.99,3.073 1.333,3.25 0.344,0.177 10 false GND 2.26,3.073 2.49,3.229 0.229,0.156 10 false +B 2.083,2.26 2.427,2.438 0.344,0.177 10 false O25

b.

Measure the voltage and resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
O25-1 (GND) - Body ground Always Below 1 Ω


Standard Voltage:
Tester Connection Condition Specified Condition
O25-5 (+B) - Body ground Always 11 to 14 V



c.

Reconnect the door control receiver connector.



OK

3.REPLACE DOOR CONTROL RECEIVER

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.REPLACE DOOR CONTROL RECEIVER
a.

Replace the door control receiver with a normal one (See page Vehicle Interior>DOOR LOCK>DOOR CONTROL RECEIVER>REMOVAL).

HINT:

If a normally functioning door control receiver is available, connect it and check if the wireless door lock function is normal or DTCs are output. If the alternative receiver functions normally, replace the original door control receiver.




NEXT

4.REGISTER RECOGNITION CODE
4.REGISTER RECOGNITION CODE
a.

Perform the registration procedures (See page Vehicle Interior>DOOR LOCK>WIRELESS DOOR LOCK CONTROL SYSTEM>REGISTRATION).



NEXT

5.CLEAR DTC
5.CLEAR DTC

NEXT

6.CONFIRM DTC
6.CONFIRM DTC
a.

Check if the same DTC is detected.

HINT:

Reinstall the sensors, connectors, etc. and restore the previous vehicle conditions before rechecking for DTCs.


OK:

DTC is not output.




OK

END (DOOR CONTROL RECEIVER DEFECTIVE)

NG

REPLACE MAIN BODY ECU