Home › Vehicle Interior › DOOR LOCK › WIRELESS DOOR LOCK CONTROL SYSTEM
RM27L0U _58 Vehicle Interior _049336 DOOR LOCK _0235813 WIRELESS DOOR LOCK CONTROL SYSTEM J

DOOR LOCK  WIRELESS DOOR LOCK CONTROL SYSTEM  No Answer-Back  


DESCRIPTION

In some cases, wireless door lock control functions are normal but the hazard warning lights and/or wireless door lock buzzer answer-back function(s) do not operate. In such cases, the main body ECU's hazard warning lights and wireless door lock buzzer signal outputs may be malfunctioning.

NOTICE:

Troubleshooting should be started after confirming that the customize status of the answer-back function has been switched ON.


WIRING DIAGRAM

B443307E01
0.99,1.885 1.146,2.083 0.156,0.198 10 false E 1.552,1.885 1.75,2.083 0.198,0.198 10 false B1 0.833,1.875 0.99,2.073 0.156,0.198 10 false 1 1.792,1.875 1.948,2.073 0.156,0.198 10 false 4 4.938,0.625 5.094,0.823 0.156,0.198 10 false 7 5.677,0.729 5.833,0.927 0.156,0.198 10 false 1 6.354,0.74 6.51,0.938 0.156,0.198 10 false 2 3.729,2.719 3.885,2.917 0.156,0.198 10 false 4 2.635,1.865 2.823,2.063 0.188,0.198 10 false 12 5.844,0.833 6,1.031 0.156,0.198 10 false B 6.177,0.833 6.333,1.031 0.156,0.198 10 false E 5.708,1.094 5.979,1.271 0.271,0.177 10 false A40 5.698,1.26 6.583,1.625 0.885,0.365 10 false Wireless Door Lock Buzzer 4.906,0.833 5.135,1.021 0.229,0.188 10 false H1 4.469,0.844 4.74,1.021 0.271,0.177 10 false BZR 4.042,2.927 4.313,3.104 0.271,0.177 10 false HAZ 3.708,2.927 3.938,3.115 0.229,0.188 10 false H2 2.5,2.438 2.771,2.615 0.271,0.177 10 false H39 2.5,2.583 3.75,2.781 1.25,0.198 10 false Turn Signal Flasher 2.875,1.979 3.146,2.156 0.271,0.177 10 false HAZ 0.917,2.281 1.188,2.458 0.271,0.177 10 false J3 0.917,2.448 1.938,2.813 1.021,0.365 10 false Hazard Warning Signal Switch 3.969,3.344 5.01,3.563 1.042,0.219 10 false Main Body ECU

PROCEDURE

1.CHECK WIRELESS DOOR LOCK CONTROL FUNCTION
a.

Check the wireless door lock control functions by operating the transmitter switch.

Result Proceed to
Wireless door lock functions are normal but hazard warning lights answer-back does not occur A
Wireless door lock functions are normal but wireless door lock buzzer answer-back does not occur B
Doors cannot be locked and unlocked with transmitter C



A

2.PERFORM ACTIVE TEST USING TECHSTREAM (FLASHER RELAY)

B

3.PERFORM ACTIVE TEST USING TECHSTREAM (WIRELESS DOOR LOCK BUZZER)

C

2.PERFORM ACTIVE TEST USING TECHSTREAM (FLASHER RELAY)
a.

Select the Active Test, use the Techstream to generate a control command, and then check that the hazard warning lights flash.

Main Body
Tester Display Test Part Control Range Diagnostic Note
Hazard Turn Signal Flasher ON/OFF -

OK:

Hazard warning lights are turned ON/OFF.




OK

REPLACE MAIN BODY ECU

NG

3.PERFORM ACTIVE TEST USING TECHSTREAM (WIRELESS DOOR LOCK BUZZER)
a.

Select the Active Test, use the Techstream to generate a control command, and then check that the wireless buzzer operates normally.

Main Body
Tester Display Test Part Control Range Diagnostic Note
Wireless Buzzer Wireless Door Lock Buzzer ON/OFF -

OK:

Wireless buzzer turns ON/OFF.




OK

REPLACE MAIN BODY ECU

NG

4.CHECK HARNESS AND CONNECTOR (WIRELESS DOOR LOCK BUZZER - MAIN BODY ECU AND BODY GROUND)
4.CHECK HARNESS AND CONNECTOR (WIRELESS DOOR LOCK BUZZER - MAIN BODY ECU AND BODY GROUND)
U153992E02
0.75,3.771 0.938,3.771 0.938,3.771 1.417,3.938 false 1.427,1.656 1.042,1.719 false 1.979,1.667 2.354,1.74 false 0.177,2.083 2.458,2.479 2.281,0.396 10 false Front view of wire harness connector: (to Main Body ECU) 0.177,0.135 2.469,0.531 2.292,0.396 10 false Front view of wire harness connector: (to Wireless Door Lock Buzzer) 0.458,1.042 0.823,1.219 0.365,0.177 10 false A40 0.5,2.844 0.823,3.021 0.323,0.177 10 false H1 0.438,3.698 0.76,3.875 0.323,0.177 10 false BZR 0.917,1.656 1.115,1.833 0.198,0.177 10 false B 2.396,1.667 2.594,1.844 0.198,0.177 10 false E

a.

Disconnect the A40 wireless door lock buzzer connector.


b.

Disconnect the H1 main body ECU connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A40-1 (B) - H1-7 (BZR) Always Below 1 Ω
A40-2 (E) - Body ground Always
A40-1 (B) or H1-7 (BZR) - Body ground Always 10 kΩ or higher



d.

Reconnect the wireless door lock buzzer and main body ECU connector.



OK

5.REPLACE WIRELESS DOOR LOCK BUZZER

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.REPLACE WIRELESS DOOR LOCK BUZZER
a.

Temporarily replace the wireless door lock buzzer with a new or normally functioning one (See page Vehicle Interior>DOOR LOCK>WIRELESS DOOR LOCK BUZZER>REMOVAL).


b.

Check that the buzzer sounds when using the transmitter LOCK and UNLOCK switches.

NOTICE:

When battery voltage is directly applied to the buzzer, the buzzer does not sound.


HINT:

The buzzer circuit is built into the main body ECU, not into the buzzer itself.




OK

END (WIRELESS DOOR LOCK BUZZER IS DEFECTIVE)

NG

REPLACE MAIN BODY ECU