CHECK MAIN BODY ECU (COWL SIDE JUNCTION BLOCK LH)
Disconnect the H3, H4, DA, DB, DC and DD ECU connectors.
Measure the voltage and resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
| DB-13 (BECU) - Body ground | GR - Body ground | +B power source | Always | 11 to 14 V |
| DA-1 (ALTB) - Body ground | B - Body ground | +B power source | Always | 11 to 14 V |
| DD-62 (GND1,GND2) - Body ground | W-B - Body ground | Power ground | Always | Below 1 Ω |
| H4-24 (DCTY) - Body ground | BR - Body ground | Driver door courtesy switch | Driver door CLOSED → OPEN | 10 kΩ or higher → Below 1 Ω |
| H3-21 (PCTY) - Body ground | BE - Body ground | Front passenger door courtesy switch input | Front passenger door CLOSED → OPEN | 10 kΩ or higher → Below 1 Ω |
| DC-2 (LCTY) - Body ground | G - Body ground*1
B - Body ground*2 |
Rear left door courtesy switch input | Rear left door CLOSED → OPEN | 10 kΩ or higher → Below 1 Ω |
| H3-25 (RRCY) - Body ground | L - Body ground | Rear right door courtesy switch input | Rear right door CLOSED → OPEN | 10 kΩ or higher → Below 1 Ω |
| DD-49 (L1) - Body ground | R - Body ground | Door control switch LOCK input | Front door control switch RH OFF → LOCK | 10 kΩ or higher → Below 1 Ω |
| DD-40 (UL1) - Body ground | W - Body ground | Front door control switch RH UNLOCK input | Front door control switch RH OFF → UNLOCK | 10 kΩ or higher → Below 1 Ω |
*1: w/ Rear Power Seat
*2: w/o Rear Power Seat
If the result is not as specified, there may be a malfunction on the wire harness side.
Reconnect the H3, H4, DA, DB, DC and DD ECU connectors.
Measure the voltage according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| H4-9 (LSWD) - Body ground | P - Body ground | Front door unlock detection switch LH input | Front door LH UNLOCK | Below 1 V |
| Front door LH LOCK | 11 to 14 V (or pulse generation ) | |||
| H3-27 (LSWP) - Body ground | V - Body ground | Front door unlock detection switch RH input | Front door RH UNLOCK | Below 1 V |
| Front door RH LOCK | 11 to 14 V (or pulse generation ) | |||
| DC-1 (LSWL) - Body ground | GR - Body ground | Rear door unlock detection switch LH input | Rear door LH UNLOCK | Below 1 V |
| Rear door LH LOCK | 11 to 14 V (or pulse generation ) | |||
| H3-5 (LSWR) - Body ground | Y - Body ground | Rear door unlock detection switch RH input | Rear door RH UNLOCK | Below 1 V |
| Rear door RH LOCK | 11 to 14 V (or pulse generation ) | |||
| DD-3 (ACT+) - Body ground | W - Body ground | Door lock motor LOCK drive output | Door control switch or front door key cylinder LH OFF | Below 1 V |
| Door control switch or front door key cylinder LH LOCK | 11 to 14 V | |||
| H4-5 (ACTD) - Body ground | P - Body ground | Door lock motor UNLOCK drive output | Door control switch or front door key cylinder LH UNLOCK | 11 to 14 V |
| Door control switch or front door key cylinder LH OFF | Below 1 V | |||
| DD-2 (ACT-) - Body ground | L - Body ground | Door lock motor UNLOCK drive output | Door control switch or front door key cylinder LH UNLOCK | 11 to 14 V |
| Door control switch or front door key cylinder LH OFF | Below 1 V | |||
| DC-24 (ACT+) - Body ground | W - Body ground | Door lock motor LOCK drive output | Door control switch or front door key cylinder LH OFF | Below 1 V |
| Door control switch or front door key cylinder LH LOCK | 11 to 14 V | |||
| DC-23 (ACT-) - Body ground | L - Body ground | Door lock motor UNLOCK drive output | Door control switch or front door key cylinder LH UNLOCK | 11 to 14 V |
| Door control switch or front door key cylinder LH OFF | Below 1 V | |||
| DD-53 (L2) - Body ground | V - Body ground | Front door key switch LH LOCK input | Front door key cylinder LH LOCK | Below 1 V |
| Ignition switch off, all doors closed and front door key cylinder LH neutral position | 11 to 14 V (or pulse generation ) | |||
| H4-10 (UL3) - Body ground | B - Body ground | Front door key switch LH UNLOCK input | Front door key cylinder LH UNLOCK | Below 1 V |
| Ignition switch off, all doors closed and front door key cylinder LH neutral position | 11 to 14 V (or pulse generation ) |
If the result is not as specified, the ECU may have a malfunction.
CHECK BACK DOOR ECU
Disconnect the V2 and V3 ECU connectors.
Measure the voltage and resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
| V2-1 (BDR) - Body ground | SB - Body ground | +B power source | Always | 11 to 14 V |
| V2-7 (BECU) - Body ground | GR - Body ground | +B power source | Always | 11 to 14 V |
| V2-6 (GND) - Body ground | W-B - Body ground | Power ground | Always | Below 1 Ω |
| V3-10 (BDCY) - V3-20 (CTYE) | P - R | Back door courtesy switch | Driver door CLOSED → OPEN | 10 kΩ or higher → Below 1 Ω |
| V3-8 (BKL) - V3-19 (KEYE) | G - BE | Tail gate control switch lock input | Back door lock cylinder is turned OFF → LOCK with mechanical key | 10 kΩ or higher → Below 1 Ω |
| V3-7 (BKUL) - V3-19 (KEYE) | LG - BE | Tail gate control switch unlock input | Back door lock cylinder is turned OFF → UNLOCK with mechanical key | 10 kΩ or higher → Below 1 Ω |
| V3-15 (HSW+) - V3-24 (HSW-) | B - W | Back door opener switch signal | Back door opener switch OFF → ON | 10 kΩ or higher → Below 1 Ω |
If the result is not as specified, there may be a malfunction on the wire harness side.
Reconnect the V2 and V3 ECU connectors.
Measure the voltage according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
| V3-8 (BKL) - Body ground | G - Body ground | Tail gate control switch lock input | Back door lock cylinder is turned OFF → LOCK with mechanical key | 11 to 14 V (or pulse generation ) → Below 1 V |
| V3-7 (BKUL) - Body ground | LG - Body ground | Tail gate control switch unlock input | Back door lock cylinder is turned OFF → UNLOCK with mechanical key | 11 to 14 V (or pulse generation ) → Below 1 V |
| V3-15 (HSW+) - Body ground | B - Body ground | Back door opener switch signal | Back door opener switch OFF → ON | 11 to 14 V (or pulse generation ) → Below 1 V |
If the result is not as specified, the ECU may have a malfunction.