Home › Vehicle Interior › LIGHTING (INT) › LIGHTING SYSTEM
RM27L0U _58 Vehicle Interior _049338 LIGHTING (INT) _0235823 LIGHTING SYSTEM U

LIGHTING (INT)  LIGHTING SYSTEM  TERMINALS OF ECU  


CHECK MAIN BODY ECU


E344926E01
0.99,3.51 1.344,3.802 0.354,0.292 2.917,3.51 3.271,3.802 0.354,0.292 5.542,3.521 5.896,3.813 0.354,0.292 1.5,5.042 1.854,5.333 0.354,0.292 4.313,5 4.667,5.292 0.354,0.292 6.01,5 6.365,5.292 0.354,0.292 0.979,6.833 1.333,7.125 0.354,0.292 3.438,6.833 3.792,7.125 0.354,0.292 5.938,6.833 6.292,7.125 0.354,0.292 2.406,1.833 2.781,1.833 true 5.031,0.958 5.469,0.958 true 1.948,1.26 2.26,1.458 0.313,0.198 10 false DC 1.948,2.073 2.26,2.271 0.313,0.198 10 false DB 2.281,1.26 2.531,1.448 0.25,0.188 10 false H4 2.833,1.75 3.083,1.938 0.25,0.188 10 false H3 2.313,2.052 2.563,2.24 0.25,0.188 10 false H2 2.323,2.313 2.573,2.5 0.25,0.188 10 false H1 2.24,2.833 2.552,3.031 0.313,0.198 10 false DA 4.948,1.656 5.26,1.854 0.313,0.198 10 false DD 1.063,3.573 1.375,3.771 0.313,0.198 10 false DA 3.01,3.563 3.323,3.76 0.313,0.198 10 false DB 5.604,3.583 5.917,3.781 0.313,0.198 10 false DC 1.583,5.104 1.896,5.302 0.313,0.198 10 false DD 4.396,5.063 4.708,5.26 0.313,0.198 10 false DE 5.521,0.885 5.833,1.083 0.313,0.198 10 false DE 6.104,5.052 6.354,5.24 0.25,0.188 10 false H1 1.073,6.896 1.323,7.083 0.25,0.188 10 false H2 3.542,6.896 3.792,7.083 0.25,0.188 10 false H3 6.031,6.896 6.281,7.083 0.25,0.188 10 false H4

a.

Disconnect the DC, DD, H3, and H4 main body ECU connectors.


b.

Measure the resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
DC-2 (LCTY) - Body ground B*1 - Body ground
G*2 - Body ground
Rear door courtesy light switch LH signal Rear door LH open → closed Below 1 Ω → 10 kΩ or higher
DD-62 (GND1, GND2) - Body ground W-B - Body ground Body ground Always Below 1 Ω
H3-21 (PCTY) - Body ground BE - Body ground Front door courtesy light switch RH signal Front door RH open → closed Below 1 Ω → 10 kΩ or higher
H3-25 (RRCY) - Body ground L - Body ground Rear door courtesy light switch RH signal Rear door RH open → closed Below 1 Ω → 10 kΩ or higher
H4-24 (DCTY) - Body ground BR - Body ground Front door courtesy light switch LH signal Front door LH open → closed Below 1 Ω → 10 kΩ or higher

*1: w/o Rear Power Seat Control System

*2: w/ Rear Power Seat Control System

If the result is not as specified, there may be a malfunction on the wire harness side.


c.

Reconnect the DC, DD, H3 and H4 main body ECU connectors.


d.

Measure the voltage according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
DB-13 (BECU) - Body ground GR - Body ground BECU power supply Always 11 to 14 V
DD-43 (IG) - Body ground LG - Body ground IG signal Ignition switch off → ON Below 1 V → 11 to 14 V
DD-45 (ACC) - Body ground BE - Body ground ACC signal Ignition switch off → ACC Below 1 V → 11 to 14 V
DD-51 (ILE) - Body ground GR - Body ground Illuminated entry system operate signal Illuminated entry system off → on 11 to 14 V → Below 1 V
H2-5 (CANH) - DD-62 (GND1, GND2) L - W-B CAN communication signal Ignition switch ON Pulse generation
(See waveform 1)
H2-6 (CANL)- DD-62 (GND1, GND2) W - W-B CAN communication signal Ignition switch ON Pulse generation
(See waveform 2)
H2-10 (LIN2) - DD-62 (GND1, GND2) V - W-B LIN communication signal Ignition switch ON Pulse generation

If the result is not as specified, the main body ECU may have a malfunction.


e.
E344927E01
2.76,0.292 3.417,0.5 0.656,0.208 10 false 1 V/DIV. 2.979,1.396 3.344,1.594 0.365,0.198 10 false GND 1.656,1.906 2.583,2.146 0.927,0.24 10 false 10 μsec./DIV.

Waveform 1 (Reference) : Using an oscilloscope

CAN Communication Signal
Terminal Name CANH - GND1, GND2
Tester Range 1 V/DIV., 10 μsec./DIV.
Condition Ignition switch ON

HINT:

The waveform varies depending on the CAN communication signal.



f.
E344928E01
2.792,0.281 3.333,0.51 0.542,0.229 10 false 1 V/DIV. 3.01,1.365 3.323,1.583 0.313,0.219 10 false GND 1.625,1.896 2.5,2.135 0.875,0.24 10 false 10 μsec./DIV.

Waveform 2 (Reference) : Using an oscilloscope

CAN Communication Signal
Terminal Name CANL - GND1, GND2
Tester Range 1 V/DIV., 10 μsec./DIV.
Condition Ignition switch ON

HINT:

The waveform varies depending on the CAN communication signal.




CHECK BACK DOOR ECU


U154019E02
1.844,0.365 2.063,0.531 0.219,0.167 10 false V2 3.906,0.375 4.125,0.542 0.219,0.167 10 false V3

a.

Disconnect the V2 and V3 back door ECU connectors.


b.

Measure the voltage and resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
V2-7 (BECU) - Body ground GR - Body ground Battery power supply Always 11 to 14 V
V2-8 (SIG) - Body ground Y - Body ground IG power supply Ignition switch off Below 1 V
Ignition switch ON 11 to 14 V
V2-6 (GND) - Body ground W-B - Body ground Ground Always Below 1 Ω
V3-10 (BDCY) - V3-20 (CTYE) P - R Back door courtesy light switch signal Back door open Below 1 Ω
Back door closed 10 kΩ or higher

If the result is not as specified, there may be a malfunction on the wire harness side.


c.

Reconnect the V2 and V3 back door ECU connectors.


d.

Measure the voltage and resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
V2-2 (LGLP) - V2-6 (GND) LG - W-B Illumination signal (to luggage compartment room light assembly) Back door closed 11 to 14 V
Back door open Below 1 V
V2-16 (MPX1) - V2-6 (GND) Y - W-B LIN communication signal Ignition switch ON Pulse generation
V3-20 (CTYE) - V2-6 (GND) R - W-B Ground for back door courtesy light switch Always Below 1 Ω

If the result is not as specified, the back door ECU may be malfunctioning.