Home › Vehicle Interior › SEAT › FRONT SEAT ASSEMBLY(for Power Seat)
RM27L0U _58 Vehicle Interior _049342 SEAT _0235862 FRONT SEAT ASSEMBLY(for Power Seat) A

SEAT  FRONT SEAT ASSEMBLY(for Power Seat)  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the LH side and RH side.

·

The procedure listed below are for the LH side.



PROCEDURE

Hide 1.INSTALL FRONT SEAT ASSEMBLY LH (w/ Leg Support Adjustment Switch)

a.

Place the front seat assembly in the cabin.

NOTICE:

Be careful not to damage the vehicle body.



b.

Connect the seat wire connectors under the seat.


c.

Connect the cable to the negative (-) battery terminal.

NOTICE:

When disconnecting the cable some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).


Torque:
5.4 N*m (55 kgf*cm, 48 in.*lbf)


d.
B167189

Operate the leg support adjustment switch to move the seat cushion to the closed position.


e.

Operate the power seat switch to move the seat to the rearmost position.


f.
B194824

Install the 2 bolts.

Torque:
37 N*m (374 kgf*cm, 27 ft.*lbf)


g.

Operate the power seat switch to move the seat to the foremost position.


h.
B191041

Install the 2 bolts.

Torque:
37 N*m (374 kgf*cm, 27 ft.*lbf)


Hide 2.INSTALL FRONT SEAT ASSEMBLY LH (w/o Leg Support Adjustment Switch)

a.

Place the front seat assembly in the cabin.

NOTICE:

Be careful not to damage the vehicle body.



b.

Connect the seat wire connectors under the seat.


c.

Connect the cable to the negative (-) battery terminal.

NOTICE:

When disconnecting the cable some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).


Torque:
5.4 N*m (55 kgf*cm, 48 in.*lbf)


d.

Operate the power seat switch to move the seat to the rearmost position.


e.
B194824

Install the 2 bolts.

Torque:
37 N*m (374 kgf*cm, 27 ft.*lbf)


f.

Operate the power seat switch to move the seat to the foremost position.


g.
B191041

Install the 2 bolts.

Torque:
37 N*m (374 kgf*cm, 27 ft.*lbf)


Hide 72138D 3.INSTALL SEAT TRACK COVER LH

a.
B200255

Attach the 2 claws to install the seat track cover.


Hide 72138E 4.INSTALL SEAT TRACK COVER INNER LH

a.
B191067

Attach the 2 claws to install the seat track cover.


Hide 71910A 5.INSTALL FRONT SEAT HEADREST ASSEMBLY

Hide 6.CHECK SRS WARNING LIGHT

Hide 7.INSPECT FRONT SEAT ASSEMBLY LH (w/ Memory)

Hide 8.INSPECT FRONT SEAT ASSEMBLY LH (w/o Memory)

Hide 9.INSPECT FRONT SEAT ASSEMBLY LH (w/ Seat Heater System)

a.

Check the seat heater operation.

i.

Turn the ignition switch ON.


ii.

When the seat heater switch is turned ON, check that the indicator light illuminates, and that the seat surface warms up in approximately 5 minutes.


iii.

When the seat heater switch's volume switch is operated, check that the seat surface temperature changes.



Hide 10.INSPECT FRONT SEAT ASSEMBLY LH (w/ Climate Control Seat System)

a.

Check the climate control operation (See page Vehicle Interior>SEAT>CLIMATE CONTROL SEAT SYSTEM>ON-VEHICLE INSPECTION).