Home › Vehicle Interior › SEAT › REAR NO. 2 SEAT ASSEMBLY(for Power Seat Type LH Side)
RM27L0U _58 Vehicle Interior _049342 SEAT _0235864 REAR NO. 2 SEAT ASSEMBLY(for Power Seat Type LH Side) A

SEAT  REAR NO. 2 SEAT ASSEMBLY(for Power Seat Type LH Side)  REASSEMBLY  


CAUTION / NOTICE / HINT

CAUTION:

Wear protective gloves. Sharp areas on the parts may injure your hands.


PROCEDURE

Hide 71607 1.INSTALL REAR NO. 2 SEAT ROD SUB-ASSEMBLY

a.
B194032

Install the rear No. 2 seat rod sub-assembly with the 2 bolts.

Torque:
18 N*m (184 kgf*cm, 13 ft.*lbf)


Hide 85820Y 2.INSTALL POWER SEAT MOTOR ASSEMBLY LH

a.
B201580

Fully rotate both lower arms in the seat folded direction as shown in the illustration.

NOTICE:

If the motor is installed with the lower arms at an intermediate position, the motor initial position will not match the seat position, so that when the seat is operated the position will be incorrect.



b.
B201581

Install the power seat motor assembly LH with the 3 bolts.

Torque:
9.0 N*m (92 kgf*cm, 80 in.*lbf)


Hide 85820X 3.INSTALL POWER SEAT MOTOR ASSEMBLY RH

a.
B201582

Install the power seat motor assembly RH with the 3 bolts.

Torque:
9.0 N*m (92 kgf*cm, 80 in.*lbf)


b.
B201583

Using a screwdriver and hammer, lightly tap the reclining connecting pipe to install it.


c.

Install the 2 washers.

NOTICE:

When the reclining connecting pipe extends about the same distance left and right, install the 2 washers.



d.
B201584

Hold the reclining connecting pipe with pliers or similar tool and rotate the reclining connecting pipe and arms to the position shown in the illustration.


Hide 79304A 4.INSTALL NO. 3 SEATBACK FRAME SUB-ASSEMBLY LH

a.
B293206

Install the No. 3 seatback frame sub-assembly LH with the 3 bolts.

Torque:
32 N*m (326 kgf*cm, 24 ft.*lbf)


Hide 72572A 5.INSTALL RECLINING CONTROL BASE LH

a.
B194027

Install the reclining control base LH with the 2 nuts.

Torque:
32 N*m (326 kgf*cm, 24 ft.*lbf)


Hide 82196 6.INSTALL REAR NO. 2 SEAT WIRE LH

a.
B293205

Attach the 5 wire harness clamps.


b.

Connect the 3 connectors to install the rear No. 2 seat wire LH.


Hide 79024 7.INSTALL NO. 2 SEATBACK COVER SUB-ASSEMBLY LH

a.
B194023E03
1.458,2.427 0.74,2.927 true 1.979,3 1.625,3.75 false 2.021,2.927 3.042,3.448 1.021,0.521 10 true Hog Ring Pliers 1.51,2.344 2.448,2.531 0.938,0.188 10 false New Hog Ring

Using hog ring pliers, install the No. 2 seatback cover sub-assembly LH to the No. 2 seatback pad with new hog rings.

NOTICE:
·

Be careful not to damage the cover.

·

When installing the hog rings, avoid wrinkling the cover.




Hide 8.INSTALL SEATBACK COVER WITH PAD

a.
B194020E03
1.552,2.5 0.927,3 false 1.948,3 1.74,3.75 false 1.583,2.417 2.531,2.615 0.948,0.198 10 false New Hog Ring 2,2.927 3.042,3.344 1.042,0.417 10 true Hog Ring Pliers

Attach the clip to install the rear seat belt hook.


b.

Using hog ring pliers, install the seatback cover with pad to the No. 3 seatback frame sub-assembly LH with a new hog ring.

NOTICE:
·

Be careful not to damage the cover.

·

When installing the hog rings, avoid wrinkling the cover.




c.
B288985

Attach the hooks.


d.

Attach the 2 wire harness clamps.


Hide 71931C 9.INSTALL REAR NO. 2 SEAT HEADREST SUPPORT ASSEMBLY

a.
B290086

Attach the 8 claws to install the 4 rear No. 2 seat headrest supports.


Hide 71970 10.INSTALL REAR SEAT HEADREST ASSEMBLY

B290078

a.

Install the rear seat headrest assembly.

NOTICE:
·

Make sure the rear seat headrest assembly is facing in the correct direction.

·

Push in the rear seat headrest assembly until the headrest lock engages.




b.
B288834E01
2.401,3.801 3.071,3.955 0.670,0.154 10 Cable End 2.388,3.887 1.819,3.887 1.819,3.887 1.603,4.008 false

Insert the cable end into the reclining control base LH.


c.

Twist the cable end in the direction indicated by the arrow to connect it and attach the cable clamp.


d.

Connect the headrest cable to the No. 3 seatback frame sub-assembly LH with the cable clamp.


e.
B288835

Attach the hook to connect the lower part of the No. 2 seatback cover sub-assembly LH.


Hide 71702C 11.INSTALL REAR SEATBACK BOARD SUB-ASSEMBLY LH

a.
B443327

Attach the 12 clips to install the rear seatback board sub-assembly LH.


Hide 72996D 12.INSTALL REAR NO. 2 SEATBACK COVER LH

a.
B195227

Attach the 3 claws to install the rear No. 2 seatback cover LH.


Hide 71940E 13.INSTALL REAR CENTER SEAT HEADREST ASSEMBLY

a.

Install the rear center seat headrest assembly.


Hide 72998B 14.INSTALL REAR SEAT CUSHION COVER LH

a.
B194006

Attach the claw.


b.

Install the rear seat cushion cover LH with the screw.


Hide 72995D 15.INSTALL REAR SEAT CUSHION COVER INNER RH

a.
B194007

Attach the claw.


b.

Install the rear seat cushion cover inner RH with the screw.


Hide 79022 16.INSTALL NO. 2 SEAT CUSHION COVER SUB-ASSEMBLY LH

a.

Using hog ring pliers, install the No. 2 seat cushion cover sub-assembly LH to the No. 2 seat cushion pad with new hog rings.

NOTICE:
·

Be careful not to damage the cover.

·

When installing the hog rings, avoid wrinkling the cover.



B443323E01
4.573,1.104 5.146,0.531 true 5.365,1.792 5.583,0.896 true 5.208,0.385 6.135,0.583 0.927,0.198 10 false New Hog Ring 5.667,0.781 6.729,1.26 1.063,0.479 10 true Hog Ring Pliers


Hide 79370A 17.INSTALL NO. 3 SEAT CUSHION SPRING ASSEMBLY LH

a.
B194003

Set the No. 3 seat cushion spring assembly LH in place.


b.

Attach the hooks.


c.
B194002E03
1.396,2.208 0.708,2.844 false 2.052,2.75 1.698,3.74 false 1.438,2.115 2.365,2.302 0.927,0.188 10 false New Hog Ring 2.094,2.667 3.083,3.073 0.99,0.406 10 true Hog Ring Pliers

Using hog ring pliers, install the No. 3 seat cushion spring assembly LH with new hog rings.

NOTICE:
·

Be careful not to damage the cover.

·

When installing the hog rings, avoid wrinkling the cover.




Hide 18.INSTALL REAR NO. 2 SEAT CUSHION ASSEMBLY LH

B194000

a.

Install the 2 bushes to the No. 3 seat cushion spring assembly LH. Then using a T45 "TORX" socket wrench, install the 2 "TORX" bolts.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)


b.

Install the rear No. 2 seat cushion assembly LH with the 2 bolts.

Torque:
32 N*m (326 kgf*cm, 24 ft.*lbf)


Hide 71692B 19.INSTALL REAR SEAT LOCK COVER OUTER LH

a.
B193996

Attach the 2 claws.


b.

Install the rear seat lock cover outer LH with the screw.


Hide 71691C 20.INSTALL REAR SEAT LOCK COVER INNER RH

a.
B193998

Attach the 3 claws.


b.

Install the rear seat lock cover inner RH with the screw.