Wear protective gloves. Sharp areas on the parts may injure your hands.
71607
1.INSTALL REAR NO. 2 SEAT ROD SUB-ASSEMBLY
Install the rear No. 2 seat rod sub-assembly with the 2 bolts.
79304A
2.INSTALL NO. 3 SEATBACK FRAME SUB-ASSEMBLY LH
Install the No. 3 seatback frame sub-assembly LH with the 5 bolts.
72620E
3.INSTALL REAR NO. 1 SEAT LOCK CABLE ASSEMBLY
Insert the rear No. 1 seat lock cable assembly through the No. 3 seatback frame sub-assembly.
Insert and rotate the cable ends to connect them.
Connect the 2 clamps.
Attach the 3 cable ties to install the rear No. 1 seat lock cable assembly.
71879E
4.INSTALL REAR SEAT RECLINING COVER INNER LH
Attach the claw.
Install the rear seat reclining cover inner LH with the screw.
71878E
5.INSTALL REAR SEAT RECLINING COVER INNER RH
Attach the claw.
Install the rear seat reclining cover inner RH with the screw.
79024
6.INSTALL NO. 2 SEATBACK COVER SUB-ASSEMBLY LH
Using hog ring pliers, install the No. 2 seatback cover sub-assembly LH to the No. 2 seatback pad with new hog rings.
Be careful not to damage the cover.
When installing the hog rings, avoid wrinkling the cover.
7.INSTALL SEATBACK COVER WITH PAD
Attach the clip to install the rear seat belt hook.
Using hog ring pliers, install the seatback cover with pad to the seatback frame with a new hog ring.
Be careful not to damage the cover.
When installing the hog rings, avoid wrinkling the cover.
Attach the hooks.
Attach the hooks.
71931C
8.INSTALL REAR NO. 2 SEAT HEADREST SUPPORT ASSEMBLY
Attach the 8 claws to install the 4 rear No. 2 seat headrest supports.
71702C
9.INSTALL REAR SEATBACK BOARD SUB-ASSEMBLY LH
Attach the 12 clips to install the rear seatback board sub-assembly LH.
72996D
10.INSTALL REAR NO. 2 SEATBACK COVER LH
Attach the 3 claws to install the rear No. 2 seatback cover LH.
72067
11.INSTALL REAR BACK LOCK CONTROL LEVER SUB-ASSEMBLY RH
Connect the rear No. 1 seat lock cable assembly in the order shown in the illustration to install the rear back lock control lever sub-assembly RH.
Install the rear back lock control lever sub-assembly RH with the screw.
72909
12.INSTALL REAR NO. 2 SEAT HANDLE
Connect the rear No. 1 seat lock cable assembly to the rear No. 2 seat handle in the order shown in the illustration.
Install the rear No. 2 seat handle with the 2 screws.
71970
13.INSTALL REAR SEAT HEADREST ASSEMBLY
Install the rear seat headrest assembly.
Make sure the rear seat headrest assembly is facing in the correct direction.
Push in the rear seat headrest assembly until the headrest lock engages.
71940E
14.INSTALL REAR CENTER SEAT HEADREST ASSEMBLY
Install the rear center seat headrest assembly.
72998B
15.INSTALL REAR SEAT CUSHION COVER LH
Attach the claw.
Install the rear seat cushion cover LH with the screw.
72995D
16.INSTALL REAR SEAT CUSHION COVER INNER RH
Attach the claw.
Install the rear seat cushion cover inner RH with the screw.
79022
17.INSTALL NO. 2 SEAT CUSHION COVER SUB-ASSEMBLY LH
Using hog ring pliers, install the No. 2 seat cushion cover sub-assembly LH to the No. 2 seat cushion pad with new hog rings.
Be careful not to damage the cover.
When installing the hog rings, avoid wrinkling the cover.
79370A
18.INSTALL NO. 3 SEAT CUSHION SPRING ASSEMBLY LH
Set the No. 3 seat cushion spring assembly LH in place.
Attach the hooks.
Using hog ring pliers, install the No. 3 seat cushion spring assembly LH with new hog rings.
Be careful not to damage the cover.
When installing the hog rings, avoid wrinkling the cover.
19.INSTALL REAR NO. 2 SEAT CUSHION ASSEMBLY LH
Install the 2 bushes to the No. 3 seat cushion spring assembly LH. Then using a T45 "TORX" socket wrench, install the 2 "TORX" bolts.
Install the rear No. 2 seat cushion assembly LH with the 2 bolts.
71692B
20.INSTALL REAR SEAT LOCK COVER OUTER LH
Attach the 2 claws.
Install the rear seat lock cover outer LH with the screw.
71691C
21.INSTALL REAR SEAT LOCK COVER INNER RH
Attach the 3 claws.
Install the rear seat lock cover inner RH with the screw.
73590
22.INSTALL REAR NO. 2 SEAT INNER BELT ASSEMBLY LH