Home › Vehicle Interior › SEAT › REAR CENTER SEAT ASSEMBLY
RM27L0U _58 Vehicle Interior _049342 SEAT _0235866 REAR CENTER SEAT ASSEMBLY A

SEAT  REAR CENTER SEAT ASSEMBLY  REASSEMBLY  


CAUTION / NOTICE / HINT

CAUTION:

Wear protective gloves. Sharp areas on the parts may injure your hands.


PROCEDURE

Hide 71237 1.INSTALL REAR SEAT BRACKET

a.
B191187

Install the rear seat bracket with the 2 nuts.

Torque:
42 N*m (428 kgf*cm, 31 ft.*lbf)


Hide 72173 2.INSTALL REAR SEAT TRACK ADJUSTING HANDLE

a.
B191186

Install the rear seat track adjusting handle.

HINT:

Install the adjusting handle straight, and check that it is centered.



Hide 72030 3.INSTALL REAR NO. 1 SEAT ADJUSTER ASSEMBLY

a.
B191185E01
0.62,0.563 0.742,0.720 0.121,0.158 10 A 0.62,0.895 0.742,1.053 0.121,0.158 10 C 0.62,1.714 0.742,1.872 0.121,0.158 10 B

Install the rear No. 1 seat adjuster assembly with nuts A, B and C in alphabetical order.


b.

Tighten nut A.

Torque:
32 N*m (326 kgf*cm, 24 ft.*lbf)


c.

Tighten nut B.

Torque:
32 N*m (326 kgf*cm, 24 ft.*lbf)


d.

Tighten nut C.

Torque:
32 N*m (326 kgf*cm, 24 ft.*lbf)


Hide 72035 4.INSTALL REAR NO. 1 SEAT ADJUSTER SUB-ASSEMBLY

a.
B191184E01
1.744,0.511 1.865,0.676 0.121,0.165 10 A 1.74,1.366 1.857,1.531 0.117,0.165 10 B 1.728,0.797 1.855,0.962 0.126,0.165 10 C

Install the rear No. 1 seat adjuster sub-assembly with nuts A, B and C in alphabetical order.


b.

Tighten nut A.

Torque:
32 N*m (326 kgf*cm, 24 ft.*lbf)


c.

Tighten nut B.

Torque:
32 N*m (326 kgf*cm, 24 ft.*lbf)


d.

Tighten nut C.

Torque:
32 N*m (326 kgf*cm, 24 ft.*lbf)


Hide 72704A 5.INSTALL REAR SEAT RECLINING CONTROL CABLE

a.
B191183

Insert the cable through the center seatback frame sub-assembly.


b.

Insert and rotate the cable ends to connect them.


c.

Connect the 2 clamps and install the rear seat reclining control cable.


Hide 71305S 6.INSTALL CENTER SEATBACK FRAME SUB-ASSEMBLY

a.
B191182E02
0.5,0.219 0.625,0.385 0.125,0.167 10 false A 0.583,1.021 0.708,1.188 0.125,0.167 10 true A 3.042,2.802 3.167,2.969 0.125,0.167 10 false B 2.625,2.865 2.75,3.031 0.125,0.167 10 false B

Using a T55 "TORX" socket, install the frame with the 2 "TORX" bolts.

·

for Bolt A


Torque:
80 N*m (816 kgf*cm, 59 ft.*lbf)


b.

Install the 2 bolts.

·

for Bolt B


Torque:
21 N*m (214 kgf*cm, 16 ft.*lbf)


Hide 71397A 7.INSTALL CENTER SEAT HINGE COVER

a.
B191180

Attach the 2 claws to install the center seat hinge cover.


b.

Install the screw.


Hide 71398H 8.INSTALL CENTER SEAT HINGE COVER UPPER LH

a.
B191181

Attach the 2 claws to install the center seat hinge cover.


b.

Install the 2 screws.


Hide 71095S 10.INSTALL CENTER SEATBACK COVER SUB-ASSEMBLY

a.
B191178

Install the center seatback cover sub-assembly to the center seatback pad.


Hide 11.INSTALL SEATBACK COVER WITH PAD

a.
B191175

Attach the hooks to install the seatback cover with pad.


b.
B195220

Attach the hooks.


c.

Using hog ring pliers, install the center seatback cover to the center seatback frame with 6 new hog rings.

B443348E01
4.333,1.156 4.875,0.667 true 5.125,1.906 5.354,1.115 true 5.417,0.969 6.417,1.354 1,0.385 10 true Hog Ring Pliers 4.938,0.521 5.865,0.719 0.927,0.198 10 false New Hog Ring

NOTICE:
·

Be careful not to damage the cover

·

When installing the hog rings, avoid wrinkling the cover.




d.
B191177E03
1.552,2.427 0.781,2.948 true 1.958,2.896 1.698,3.813 false 1.583,2.333 2.531,2.521 0.948,0.188 10 false New Hog Ring 2.021,2.792 3.042,3.25 1.021,0.458 10 true Hog Ring Pliers

Using hog ring pliers, install the center seatback cover to the center seatback frame with 5 new hog rings.

NOTICE:
·

Be careful not to damage the cover

·

When installing the hog rings, avoid wrinkling the cover.




Hide 71303C 12.INSTALL REAR SEATBACK HINGE SUB-ASSEMBLY RH

a.
B191174

Install the rear seatback hinge sub-assembly with the bolt.


Hide 71304C 13.INSTALL REAR SEATBACK HINGE SUB-ASSEMBLY LH

a.
B191173

Install the rear seatback hinge sub-assembly with the bolt.


Hide 72868 14.INSTALL CENTER ARMREST HINGE COVER RH

a.
B191172

To install the center armrest hinge cover RH, slide it rearward install the screw, as shown in the illustration.


Hide 72869 15.INSTALL CENTER ARMREST HINGE COVER LH

a.
B191171

To install the center armrest hinge cover LH, slide it rearward install the screw, as shown in the illustration.


Hide 16.INSTALL ARMREST ASSEMBLY

a.
B191167

Install the armrest assembly with the 2 nuts.

Torque:
20 N*m (204 kgf*cm, 15 ft.*lbf)


Hide 73373F 17.INSTALL REAR SEAT SHOULDER BELT HOLE COVER NO. 3

a.
B191168

Attach the 2 claws, to the rear seat shoulder belt hole cover.


b.

Install the rear seat shoulder belt hole cover with the 2 screws.


Hide 71931A 18.INSTALL REAR SEAT HEADREST SUPPORT

a.
B191166E02
1.49,0.385 2.781,1.448 2.781,1.448 2.781,0.385 true 2.49,1.448 3.156,1.625 0.667,0.177 10 false Protruding

Align the protruding portion of the rear seat headrest supports with the installation grooves of the center seatback frame.


b.

Attach the 4 claws to install the 2 rear seat headrest supports.


Hide 72058A 19.INSTALL REAR SEAT LOCK CONTROL LEVER SUB-ASSEMBLY LH

a.
B191245E01
1.233,2.565 1.336,2.723 0.103,0.158 10 1 0.905,2.906 1.008,3.064 0.103,0.158 10 2

Connect the cable in the order shown in the illustration to install the rear seat lock control lever sub-assembly.


b.

Install the rear seat lock control lever sub-assembly with the 2 screws.


Hide 72615C 20.INSTALL REAR SEATBACK LOCK STRIKER COVER

a.
B191164

Attach the guide and claw to install the rear seatback lock striker cover.


Hide 73373F 21.INSTALL REAR SEAT SHOULDER BELT HOLE COVER NO. 2

a.
B191162

Using a T30 "TORX" socket, install the rear seat shoulder belt hole cover with the 2 "TORX" bolts.

Torque:
0.9 N*m (9.2 kgf*cm, 8.0 in.*lbf)


Hide 72667 22.INSTALL REAR SEATBACK LOCK BEZEL UPPER

a.
B191161

Install the rear seatback lock bezel upper with the 2 screws.


b.
B191159

Install the center seat outer belt lower bolt.

Torque:
42 N*m (428 kgf*cm, 31 ft.*lbf)


Hide 73373F 23.INSTALL REAR SEAT SHOULDER BELT HOLE COVER NO. 1

a.
B191160

Attach the 4 claws to install the rear seat shoulder belt hole cover.


Hide 72927B 25.INSTALL REAR SEAT CUSHION UNDER COVER

a.
B191157

Install the rear seat cushion under cover with the 2 screws.


Hide 71395B 26.INSTALL CENTER SEAT HINGE COVER RH

a.
B191156

Attach the 3 claws and clip to install the center seat hinge cover.


b.

Install the screw.


Hide 71396B 27.INSTALL CENTER SEAT HINGE COVER LH

a.
B191155

Attach the 3 claws and clip to install the center seat hinge cover.


b.

Install the screw.


Hide 71087 28.INSTALL REAR SEATBACK BOARD SUB-ASSEMBLY

a.
B191154

Attach the 6 clips to install the rear seatback board sub-assembly.


Hide 71960B 29.INSTALL REAR CENTER SEAT HEADREST ASSEMBLY

Hide 71097S 30.INSTALL CENTER SEAT CUSHION COVER SUB-ASSEMBLY

a.
B191153E03
1.396,2.417 0.74,2.927 true 1.854,2.792 1.698,3.771 false 1.448,2.333 2.417,2.521 0.969,0.188 10 false New Hog Ring 1.896,2.698 2.906,3.094 1.01,0.396 10 true Hog Ring Pliers

Using hog ring pliers, install the center seat cushion cover to the center seat cushion pad with 7 new hog rings.

NOTICE:
·

Be careful not to damage the cover

·

When installing the hog rings, avoid wrinkling the cover.




Hide 71650 31.INSTALL REAR SEAT CUSHION SPRING ASSEMBLY

a.
B191151

Attach the hooks and install the seat cushion spring assembly.


Hide 32.INSTALL CENTER SEAT CUSHION ASSEMBLY

B191150E02
0.906,0.292 1.042,0.5 0.135,0.208 10 true A 3.302,1.771 3.417,1.938 0.115,0.167 10 false A 1.365,2.51 1.479,2.677 0.115,0.167 10 false B 0.542,2.083 0.656,2.25 0.115,0.167 10 false B

a.

Install the 2 bushes to the cushion spring. Then, using a T45 "TORX" socket, install the 2 "TORX" bolts.

·

for Bolt A


Torque:
21 N*m (214 kgf*cm, 16 ft.*lbf)


b.

Install the 2 bolts.

·

for Bolt B


Torque:
32 N*m (326 kgf*cm, 24 ft.*lbf)


c.
B191149

Attach the hook and loop fastener and hook.


d.

Pass the inner belt through the hole of the seat cushion.


Hide 71691D 33.INSTALL REAR SEAT CUSHION HINGE COVER UPPER RH

a.
B191148

Attach the 2 claws to install the rear seat cushion hinge cover upper.


b.

Install the screw.


c.

Attach the hook.


Hide 71692D 34.INSTALL REAR SEAT CUSHION HINGE COVER UPPER LH

a.
B191147

Attach the 2 claws to install the rear seat cushion hinge cover upper.


b.

Install the screw.


c.

Attach the hook.