Home › Vehicle Interior › SEAT › SEAT HEATER SWITCH(for Rear No. 1 Seat)
RM27L0U _58 Vehicle Interior _049342 SEAT _0235872 SEAT HEATER SWITCH(for Rear No. 1 Seat) G

SEAT  SEAT HEATER SWITCH(for Rear No. 1 Seat)  INSPECTION  


PROCEDURE

Hide 84751G 1.INSPECT SEAT HEATER SWITCH LH

B194045E03
1.188,3.01 1.427,3.854 false 1.823,3.844 2.125,3.021 false 1.625,4.021 1.625,4.333 false 1.24,4.031 1.24,4.344 false 2.01,4.031 2.01,4.333 false 0.979,3.938 0.531,3.938 false 2.219,3.844 2.729,3.031 false 2.469,0.49 1.813,0.688 false 2.469,1.01 1.813,1.01 false 2.469,1.563 1.813,1.365 false 0.781,2.927 1.083,3.104 0.302,0.177 10 false ILL+ 1.896,4.354 2.115,4.51 0.219,0.156 10 false LO 1.531,4.365 1.719,4.521 0.188,0.156 10 false HI 2.188,2.927 2.323,3.063 0.135,0.135 10 false E 0.052,1.99 2.583,2.313 2.531,0.323 10 false Component without harness connected: (Seat Heater Switch) 1.135,4.365 1.323,4.521 0.188,0.156 10 false IG 2.75,2.927 2.896,3.094 0.146,0.167 10 false R 0.198,3.865 0.479,4.031 0.281,0.167 10 false IND 2.5,0.927 3.24,1.094 0.74,0.167 10 false Illumination 2.5,0.406 3.073,0.573 0.573,0.167 10 false Indicator 2.5,1.479 3.073,1.646 0.573,0.167 10 false Indicator

a.

Check the resistance.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
5 (HI) - 4 (E) Switch ON (HI) Below 1 Ω
5 (HI) - 4 (E) Switch OFF 10 kΩ higher
3 (LO) - 4 (E) Switch ON (LO) Below 1 Ω
3 (LO) - 4 (E) Switch OFF 10 kΩ higher


If the result is not as specified, replace the switch.



b.

Check the illumination operation.

i.

Apply battery voltage to the switch connector, and check that the seat heater switch illuminates.

OK:
Measurement Condition Switch Condition Specified Condition
Battery positive (+) → 6 (ILL+)
Battery negative (-) → 4 (E)
Always Illuminates


If the result is not as specified, replace the switch.



c.

Check the indicator operation.

i.

Apply battery voltage to the switch connector, and check that the seat heater switch illuminates.

OK:
Measurement Condition Switch Condition Specified Condition
Battery positive (+) → 7 (IG)
Battery negative (-) → 8 (IND)
Switch ON (HI) Illuminates
Battery positive (+) → 7 (IG)
Battery negative (-) → 2 (R)
Switch ON (LO) Illuminates


If the result is not as specified, replace the switch.



Hide 84751G 2.INSPECT SEAT HEATER SWITCH RH

B195230E03
1.188,3 1.427,3.844 false 1.813,3.854 2.125,3.01 false 1.625,4.01 1.625,4.323 false 1.24,4.021 1.24,4.333 false 2.01,4.021 2.01,4.323 false 0.99,3.958 0.542,3.958 false 2.219,3.833 2.729,3.021 false 2.438,0.531 1.813,0.698 false 2.458,1 1.833,1 false 2.458,1.552 1.802,1.354 false 0.844,2.906 1.146,3.083 0.302,0.177 10 false ILL+ 1.896,4.344 2.115,4.5 0.219,0.156 10 false LO 1.531,4.354 1.719,4.51 0.188,0.156 10 false HI 2.188,2.906 2.323,3.042 0.135,0.135 10 false E 0.052,1.979 2.583,2.302 2.531,0.323 10 false Component without harness connected: (Seat Heater Switch) 1.135,4.354 1.323,4.51 0.188,0.156 10 false IG 2.792,2.917 2.958,3.115 0.167,0.198 10 false R 0.24,3.885 0.521,4.042 0.281,0.156 10 false IND 2.49,0.917 3.229,1.083 0.74,0.167 10 false Illumination 2.479,0.427 3.052,0.594 0.573,0.167 10 false Indicator 2.49,1.469 3.063,1.635 0.573,0.167 10 false Indicator

a.

Check the resistance.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
5 (HI) - 4 (E) Switch ON (HI) Below 1 Ω
5 (HI) - 4 (E) Switch OFF 10 kΩ higher
3 (LO) - 4 (E) Switch ON (LO) Below 1 Ω
3 (LO) - 4 (E) Switch OFF 10 kΩ higher


If the result is not as specified, replace the switch.



b.

Check the illumination operation.

i.

Apply battery voltage to the switch connector, and check that the seat heater switch illuminates.

OK:
Measurement Condition Switch Condition Specified Condition
Battery positive (+) → 6 (ILL+)
Battery negative (-) → 4 (E)
Always Illuminates


If the result is not as specified, replace the switch.



c.

Check the indicator operation.

i.

Apply battery voltage to the switch connector, and check that the seat heater switch illuminates.

OK:
Measurement Condition Switch Condition Specified Condition
Battery positive (+) → 7 (IG)
Battery negative (-) → 8 (IND)
Switch ON (HI) Illuminates
Battery positive (+) → 7 (IG)
Battery negative (-) → 2 (R)
Switch ON (LO) Illuminates


If the result is not as specified, replace the switch.