Home › Vehicle Interior › SEAT › FRONT POWER SEAT CONTROL SYSTEM(w/ Memory)
RM27L0U _58 Vehicle Interior _049342 SEAT _0235877 FRONT POWER SEAT CONTROL SYSTEM(w/ Memory) U

SEAT  FRONT POWER SEAT CONTROL SYSTEM(w/ Memory)  TERMINALS OF ECU  


CHECK FRONT POWER SEAT SWITCH LH


U153195E02
4.667,0.26 4.958,0.438 0.292,0.177 10 false X11 2.333,0.385 2.573,0.552 0.24,0.167 10 false X10

a.

Disconnect the X10 and X11 switch connectors.


b.

Measure the voltage and resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
X10-1 (GND) - Body ground W-B - Body ground Ground Always Below 1 Ω
X10-5 (+B) - X10-1 (GND) L - W-B Battery (ECU power source) Always 11 to 14 V
X11-4 (IG) - X10-1 (GND) BR - W-B Ignition switch signal Ignition switch off Below 1 V
Ignition switch ON 11 to 14 V
X11-8 (SYSB) - X10-1 (GND) R - W-B Battery (ECU power source) Always 11 to 14 V

If the result is not as specified, there may be a malfunction on the wire harness side.


c.

Reconnect the X10 and X11 switch connectors.


d.

Measure the voltage according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
X10-2 (SLD+) - X10-1 (GND) P - W-B Sliding motor signal (forward) Seat moving forward using sliding switch 11 to 14 V
Other Below 1 V
X10-3 (SLD-) - X10-1 (GND) R - W-B Sliding motor signal (rearward) Seat moving rearward using sliding switch 11 to 14 V
Other Below 1 V
X10-4 (FRV-) - X10-1 (GND) W - W-B Front vertical motor signal (downward) Seat cushion front portion lowering using front vertical switch 11 to 14 V
Other Below 1 V
X10-6 (FRV+) - X10-1 (GND) LG - W-B Front vertical motor signal (upward) Seat cushion front portion rising using front vertical switch 11 to 14 V
Other Below 1 V
X10-7 (LFT+) - X10-1 (GND) G - W-B Lifter motor signal (upward) Seat cushion rising using lifter switch 11 to 14 V
Other Below 1 V
X10-8 (RCL+) - X10-1 (GND) BE - W-B Reclining motor signal (forward) Seatback moving forward using reclining switch 11 to 14 V
Other Below 1 V
X10-9 (LFT-) - X10-1 (GND) Y - W-B Lifter motor signal (downward) Seat cushion lowering using lifter switch 11 to 14 V
Other Below 1 V
X10-10 (RCL-) - X10-1 (GND) B - W-B Reclining motor signal (rearward) Seatback moving rearward using reclining switch 11 to 14 V
Other Below 1 V

If the result is not as specified, the ECU may have a malfunction.



CHECK OUTER MIRROR CONTROL ECU


U153194E02
4.458,0.469 4.688,0.646 0.229,0.177 10 false M7 2.865,0.458 3.073,0.635 0.208,0.177 10 false M8

a.

Disconnect the M7 and M8 ECU connectors.


b.

Measure the voltage and resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
M7-3 (B) - M7-9 (GND) R - W-B Battery (ECU power source) Always 11 to 14 V
M7-4 (ACC) - M7-9 (GND) Y - W-B Ignition power supply Ignition switch off Below 1 V
Ignition switch ON 11 to 14 V
M7-9 (GND) - Body ground W-B - Body ground Ground Always Below 1 Ω
M8-10 (MSWE) - M7-9 (GND) V - W-B Ground for seat memory switch Always Below 1 Ω

If the result is not as specified, there may be a malfunction on the wire harness side.


c.

Reconnect the M7 and M8 ECU connectors.


d.

Measure the voltage according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
M8-7 (M2) - M8-10 (MSWE) BE - V Memory 2 switch signal Memory 2 switch OFF 11 to 14 V
Memory 2 switch ON Below 1 V
M8-8 (M1) - M8-10 (MSWE) P - V Memory 1 switch signal Memory 1 switch OFF 11 to 14 V
Memory 1 switch ON Below 1 V
M8-9 (MM) - M8-10 (MSWE) L - V Memory SET switch signal Memory SET switch OFF 11 to 14 V
Memory SET switch ON Below 1 V

If the result is not as specified, the ECU may have a malfunction.