DATA LIST
Using the Techstream to read the Data List allows values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Turn the Techstream ON.
Enter the following menus: Body Electrical or Power train / (desired system) / Data List.
According to the display on the Techstream, read the Data List.
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
|---|---|---|---|
| Driver Side SET Mem SW | Driver side seat memory SET switch / ON or OFF | ON: Driver side seat memory SET switch on
OFF: Driver side seat memory SET switch off |
- |
| Driver Side Memory SW 1 | Driver side seat memory switch 1 / ON or OFF | ON: Driver side seat memory switch 1 on
OFF: Driver side seat memory switch 1 off |
- |
| Driver Side Memory SW 2 | Driver side seat memory switch 2 / ON or OFF | ON: Driver side seat memory switch 2 on
OFF: Driver side seat memory switch 2 off |
- |
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
|---|---|---|---|
| Reclining Rear | Reclining switch signal (Rearward) / ON or OFF | ON: Reclining switch (Rearward) on
OFF: Reclining switch (Rearward) off |
- |
| Reclining Front | Reclining switch signal (Forward) / ON or OFF | ON: Reclining switch (Forward) on
OFF: Reclining switch (Forward) off |
- |
| Front Vertical Down | Front vertical switch signal (Downward) / ON or OFF | ON: Front vertical switch (Downward) on
OFF: Front vertical switch (Downward) off |
- |
| Front Vertical Up | Front vertical switch signal (Upward) / ON or OFF | ON: Front vertical switch (Upward) on
OFF: Front vertical switch (Upward) off |
- |
| Lifter Switch Down | Lifter switch signal (Downward) / ON or OFF | ON: Lifter switch (Downward) on
OFF: Lifter switch (Downward) off |
- |
| Lifter Switch Up | Lifter switch signal (Upward) / ON or OFF | ON: Lifter switch (Upward) on
OFF: Lifter switch (Upward) off |
- |
| Slide Rear | Sliding switch signal (Rearward) / ON or OFF | ON: Sliding switch (Rearward) on
OFF: Sliding switch (Rearward) off |
- |
| Slide Front | Sliding switch signal (Forward) / ON or OFF | ON: Sliding switch (Forward) on
OFF: Sliding switch (Forward) off |
- |
| SET Switch | Seat memory SET switch signal / ON or OFF | ON: Seat memory SET switch on
OFF: Seat memory SET switch off |
- |
| M1 Switch | Seat memory switch 1 signal / ON or OFF | ON: Seat memory switch 1 on
OFF: Seat memory switch 1 off |
- |
| M2 Switch | Seat memory switch 2 signal / ON or OFF | ON: Seat memory switch 2 on
OFF: Seat memory switch 2 off |
- |
| M3 Switch | - | - | - |
| Seat Memory No1 | Seat position memorized with seat memory switch 1 / Mem or Not Mem | Mem: Memorized
Not Mem: Not memorized |
- |
| Seat Memory No2 | Seat position memorized with seat memory switch 2 / Mem or Not Mem | Mem: Memorized
Not Mem: Not memorized |
- |
| Seat Memory No3 | - | - | - |
| Ignition Switch | Ignition switch signal / ON or OFF | ON: Ignition switch ON signal received
OFF: Ignition switch off signal received |
- |
| Key Switch | Ignition switch status / ON or OFF | ON: Ignition switch ON
OFF: Ignition switch off |
- |
| Key Code Confirm | - | - | - |
| D-Door Courtesy | Door courtesy switch signal / ON or OFF | ON: Driver side door open
OFF: Driver side door closed |
- |
| P Switch | Shift lever position P signal / ON or OFF | ON: Shift lever in P
OFF: Shift lever not in P |
- |
| Parking Brake SW | Parking brake switch status / ON or OFF | ON: Parking brake operated
OFF: Parking brake released |
- |
| Vehicle Speed | Vehicle speed data / Min.: 0 km/h (0 mph), Max.: 255 km/h (158 mph) | Actual vehicle speed | - |
| Power Voltage | Power supply for driver seat ECU / MIN: 0 V, MAX: 19.89 V | Within range from 11 V to 14 V | - |
| Slide Position | Seat sliding position / MIN: 4096, MAX: 61440 | Within range from 4096 to 61440 | - |
| Reclining Position | Seatback position / MIN: 4096, MAX: 61440 | Within range from 4096 to 61440 | - |
| Front Vertical Position | Seat front vertical position / MIN: 4096 MAX: 61440 | Within range from 4096 to 61440 | - |
| Lifter Position | Seat lifter position / MIN: 4096 MAX: 61440 | Within range from 4096 to 61440 | - |
| Slide Pos Mem No1 | Seat sliding position memorized with seat memory switch 1 / MIN: 4096, MAX: 61440 | Within range from 4096 to 61440 | - |
| Reclining Pos Mem No1 | Seatback position memorized with seat memory switch 1 / MIN: 4096, MAX: 61440 | Within range from 4096 to 61440 | - |
| Frnt Vrtcl Pos Mem No1 | Front vertical position memorized with seat memory switch 1 / MIN: 4096, MAX: 61440 | Within range from 4096 to 61440 | - |
| Lifter Pos Mem No1 | Lifter position memorized with seat memory switch 1 / MIN: 4096, MAX: 61440 | Within range from 4096 to 61440 | - |
| Slide Pos Mem No2 | Seat sliding position memorized with seat memory switch 2 / MIN: 4096, MAX: 61440 | Within range from 4096 to 61440 | - |
| Reclining Pos Mem No2 | Seatback position memorized with seat memory switch 2 / MIN: 4096, MAX: 61440 | Within range from 4096 to 61440 | - |
| Frnt Vrtcl Pos Mem No2 | Front vertical position memorized with seat memory switch 2 / MIN: 4096, MAX: 61440 | Within range from 4096 to 61440 | - |
| Lifter Pos Mem No2 | Lifter position memorized with seat memory switch 2 / MIN: 4096, MAX: 61440 | Within range from 4096 to 61440 | - |
| Slide Pos Mem No3 | - | - | - |
| Reclining Pos Mem No3 | - | - | - |
| Frnt Vrtcl Pos Mem No3 | - | - | - |
| Lifter Pos Mem No3 | - | - | - |
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
|---|---|---|---|
| Shift SW Status (P Range) | PNP switch status / ON or OFF | ON: Shift lever in P
OFF: Shift lever not in P |
- |
ACTIVE TEST
Using the Techstream to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Turn the Techstream ON.
Enter the following menus: Body Electrical / Driver Seat / Active Test.
According to the display on the Techstream, perform the Active Test.
| Tester Display | Test Part | Control Range | Diagnostic Note |
|---|---|---|---|
| Seat Reclining | Seat reclining operation | Front/OFF/Rear | - |
| Front Vertical Operation | Seat front vertical operation | Up/OFF/Down | - |
| Lifter Operation | Seat lifter operation | Up/OFF/Down | - |
| Seat Slide Operation | Seat sliding operation | Front/OFF/Rear | - |
| Buzzer | Buzzer operation | ON/OFF | - |