Home › Vehicle Interior › SEAT › REAR POWER SEAT CONTROL SYSTEM
RM27L0U _58 Vehicle Interior _049342 SEAT _0235879 REAR POWER SEAT CONTROL SYSTEM J

SEAT  REAR POWER SEAT CONTROL SYSTEM  Park / Neutral Position Switch Circuit  


DESCRIPTION

The fold seat control ECU receives signals from the Park/Neutral position switch and controls the seat folding and return operations. The shift lever is in any position other than P when the ignition switch is ON, the seat cannot be operated.

WIRING DIAGRAM

B193666E06
5.125,2.208 5.406,2.365 0.281,0.156 10 false P20 5.448,2.208 5.74,2.354 0.292,0.146 10 false O34 5.802,2.177 5.938,2.333 0.135,0.156 10 false P 3.729,2.094 3.927,2.25 0.198,0.156 10 false PL 2.99,2.094 3.208,2.24 0.219,0.146 10 false RB 0.594,2.188 1.896,2.385 1.302,0.198 10 false from IG No. 1 Relay 5.188,2 5.365,2.156 0.177,0.156 10 false 32 5.521,2 5.708,2.146 0.188,0.146 10 false 32 3.969,2.094 4.156,2.24 0.188,0.146 10 false 6 2.781,2.094 2.875,2.24 0.094,0.146 10 false 2 2.552,2.667 2.875,2.865 0.323,0.198 10 false D21 5.458,4.167 7.073,4.365 1.615,0.198 10 false Fold Seat Control ECU 2.552,2.854 4.469,3.052 1.917,0.198 10 false Park/Neutral Position Switch 5.177,2.396 5.354,2.552 0.177,0.156 10 false *2 5.51,2.396 5.677,2.552 0.167,0.156 10 false *1 0.281,4.302 1.063,4.49 0.781,0.188 10 false *2: RH Side 0.281,3.99 1.031,4.177 0.75,0.188 10 false *1: LH Side

PROCEDURE

1.CHECK FOLD SEAT CONTROL ECU (PARK/NEUTRAL POSITION SWITCH SIGNAL)
a.
U153323E02
1.219,1.802 0.854,2.188 true 0.094,0.031 2.375,0.625 2.281,0.594 10 false Component with harness connector: (Fold Seat Control ECU) 1.469,0.979 1.729,1.156 0.26,0.177 10 false P20 0.74,0.979 1.021,1.156 0.281,0.177 10 false O34 0.792,2.188 1,2.365 0.208,0.177 10 false P 1.135,0.979 1.302,1.135 0.167,0.156 10 false *1 1.854,0.979 2.021,1.135 0.167,0.156 10 false *2 0.073,2.698 0.833,2.896 0.76,0.198 10 false *1: LH Side 0.073,3.021 0.833,3.219 0.76,0.198 10 false *2: RH Side

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
LH Side
Tester Connection Condition Specified Condition
O34-32 (P) - body ground Ignition switch ON
Park/Neutral position switch P position
11 to 14 V
Ignition switch ON
Park/Neutral position switch not in P position
Below 1 V

RH Side
Tester Connection Condition Specified Condition
P20-32 (P) - body ground Ignition switch ON
Park/Neutral position switch P position
11 to 14 V
Ignition switch ON
Park/Neutral position switch not in P position
Below 1 V




OK

PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE

NG

2.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH - IGNITION SWITCH)
2.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH - IGNITION SWITCH)
a.
U153452E02
1.76,1.656 2.115,1.156 true 2.167,1.042 2.375,1.219 0.208,0.177 10 false RB 0.063,0 2.469,0.365 2.406,0.365 10 false Front view of wire harness connector: (to Park/Neutral Position Switch) 0.365,1.656 0.656,1.813 0.292,0.156 10 false D21

Disconnect the D21 switch connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
D21-2 (RB) - Body ground Ignition switch ON 11 to 14 V
Ignition switch off Below 1 V




OK

3.INSPECT PARK/NEUTRAL POSITION SWITCH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT PARK/NEUTRAL POSITION SWITCH
a.
C160109E36
1.354,1.667 1.104,1.177 true 2.292,2.385 2.01,1.885 false 1.99,2.385 1.896,1.938 false 1.615,1.667 1.531,1.177 true 0.052,0 2.635,0.365 2.583,0.365 10 false Component without harness connected: (Park/Neutral Position Switch) 0.979,1 1.135,1.167 0.156,0.167 10 false B 1.417,0.958 1.625,1.135 0.208,0.177 10 false RB 2.302,2.427 2.51,2.604 0.208,0.177 10 false L 2,2.427 2.208,2.604 0.208,0.177 10 false PL

Disconnect the D21 switch connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
2 (RB) - 6 (PL)
4 (B) - 5 (L)
Shift lever in P Below 1 Ω
2 (RB) - 6 (PL)
4 (B) - 5 (L)
Shift lever not in P 10 kΩ or higher


Result
Result Proceed to
OK A
NG (A760E automatic transmission) B
NG (A760F automatic transmission) C
NG (AB60E automatic transmission) D
NG (AB60F automatic transmission) E



A

REPAIR OR REPLACE HARNESS OR CONNECTOR (FOLD SEAT CONTROL ECU - PARK/NEUTRAL POSITION SWITCH)

B

C