Home › Vehicle Interior › SEAT › SEAT HEATER SYSTEM
RM27L0U _58 Vehicle Interior _049342 SEAT _0235880 SEAT HEATER SYSTEM G

SEAT  SEAT HEATER SYSTEM  ON-VEHICLE INSPECTION  


PROCEDURE

Hide 87501B 1.INSPECT SEAT HEATER CONTROL SUB-ASSEMBLY LH (for Front Seat)

a.
U153190E02
0.656,2.063 1.281,2.063 false 2.146,2.49 2.677,2.854 false 1.531,2.49 1.083,2.854 false 0.094,0.063 2.365,0.479 2.271,0.417 10 false Front view of wire harness connector: (to Seat Heater Control) 1.573,1.052 1.844,1.24 0.271,0.188 10 false X12 0.25,1.979 0.604,2.146 0.354,0.167 10 false SWL 2.677,2.854 2.802,3.042 0.125,0.188 10 false E 0.958,2.854 1.083,3.021 0.125,0.167 10 false B

Disconnect the X12 heater control connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
X12-6 (E) - Body ground Always Below 1 Ω


If the result is not as specified, there may be a malfunction on the wire harness side.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
X12-1 (SWL) - X12-6 (E) Ignition switch ON
Seat heater switch OFF
Below 1 V
Ignition switch ON
Seat heater switch ON
11 to 14 V
X12-4 (B) - X12-6 (E) Ignition switch OFF Below 1 V
Ignition switch ON 11 to 14 V


If the result is not as specified, there may be a malfunction on the wire harness side.


d.

Connect the X12 heater control connector.


e.
U153199E01
0.036,0.003 2.356,0.646 2.321,0.642 10 Component with harness connector: (Seat Heater Control) 0.713,1.969 1.005,2.123 0.292,0.154 10 THL 0.97,1.96 1.581,1.46 false 0.118,1.087 0.382,1.268 0.264,0.181 10 X12

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
X12-5 (THL) - Body ground Ignition switch ON
Seat heater switch ON, volume MIN → MAX (for Limited and SR5 grade)
Seat heater switch ON, volume 1 → 3 (for Platinum grade)
Gradual increase between below 1 V and 11 to 14 V


If the result is not as specified, the seat heater control may have a malfunction.


Hide 87501A 2.INSPECT SEAT HEATER CONTROL SUB-ASSEMBLY RH (for Front Seat)

a.
U153191E02
0.771,2.104 1.281,2.104 false 1.26,2.865 1.542,2.458 false 2.573,2.865 2.167,2.458 false 1.583,1.042 1.854,1.229 0.271,0.188 10 false W8 0.365,2.021 0.74,2.188 0.375,0.167 10 false SWR 2.521,2.875 2.667,3.063 0.146,0.188 10 false E 1.115,2.865 1.323,3.031 0.208,0.167 10 false B1 0.094,0.104 2.365,0.469 2.271,0.365 10 false Front view of wire harness connector: (to Seat Heater Control)

Disconnect the W8 heater control connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
W8-6 (E) - Body ground Always Below 1 Ω


If the result is not as specified, there may be a malfunction on the wire harness side.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
W8-1 (SWR) - W8-6 (E) Ignition switch ON
Seat heater switch OFF
Below 1 V
Ignition switch ON
Seat heater switch ON
11 to 14 V
W8-4 (B1) - W8-6 (E) Ignition switch OFF Below 1 V
Ignition switch ON 11 to 14 V


If the result is not as specified, there may be a malfunction on the wire harness side.


d.

Connect the W8 heater control connector.


e.
U153200E01
0.036,0.003 2.356,0.646 2.321,0.642 10 Component with harness connector: (Seat Heater Control) 0.15,1.154 0.412,1.308 0.261,0.154 10 W8 0.713,1.969 1.042,2.123 0.329,0.154 10 THR 0.97,1.96 1.581,1.46 false

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
W8-5 (THR) - Body ground Ignition switch ON
Seat heater switch ON, volume MIN → MAX (for Limited and SR5 grade)
Seat heater switch ON, volume 1 → 3 (for Platinum grade)
Gradual increase between below 1 V and 11 to 14 V


If the result is not as specified, the seat heater control may have a malfunction.


Hide 87501 3.INSPECT SEAT HEATER CONTROL SUB-ASSEMBLY LH (for Rear No. 1 Seat)

a.
U153223E02
1.896,2.438 1.99,2.76 false 1.531,2.438 1.438,2.76 false 1.302,1.979 0.99,1.979 false 2.083,2.333 2.385,2.563 false 0.135,0 2.385,0.365 2.25,0.365 10 false Front view of wire harness connector: (to Seat Heater Control) 0.792,1.896 0.938,2.104 0.146,0.208 10 false B 1.906,2.792 2.198,2.99 0.292,0.198 10 false HIL 1.26,2.771 1.615,2.99 0.354,0.219 10 false SWL 2.427,2.521 2.604,2.729 0.177,0.208 10 false E 1.583,0.979 1.875,1.177 0.292,0.198 10 false O43

Disconnect the O43 heater control connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
O43-10 (SWL) - O43-13 (E) Seat heater LO switch OFF 10 kΩ or higher
Seat heater LO switch ON Below 1 Ω
O43-12 (HIL) - O43-13 (E) Seat heater HI switch OFF 10 kΩ or higher
Seat heater HI switch ON Below 1 Ω
O43-13 (E) - Body ground Always Below 1 Ω


If the result is not as specified, there may be a malfunction on the wire harness side.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
O43-1 (B) - O43-13 (E) Always 11 to 14 V


If the result is not as specified, there may be a malfunction on the wire harness side.


d.

Connect the O43 heater control connector.


e.
B188617E01
0.057,0.078 2.312,0.437 2.254,0.359 10 Component with harness connector: (Seat Heater Control)

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
1 - Body ground Ignition switch ON
Seat heater switch OFF
Below 1 V
Ignition switch ON
Seat heater LO or HI switch ON
11 to 14 V


HINT:
·

When the heater reaches the specified temperature, the power turns off.

·

If the result is not as specified, the seat heater control may have a malfunction.




Hide 87501 4.INSPECT SEAT HEATER CONTROL SUB-ASSEMBLY RH (for Rear No. 1 Seat)

a.
U153224E02
1.896,2.438 1.99,2.76 false 1.531,2.427 1.438,2.75 false 1.302,1.99 0.99,1.99 false 2.104,2.333 2.406,2.563 false 0.135,0 2.385,0.344 2.25,0.344 10 false Front view of wire harness connector: (to Seat Heater Control) 0.781,1.906 1,2.115 0.219,0.208 10 false B1 1.917,2.771 2.219,3.021 0.302,0.25 10 false HIR 1.24,2.771 1.594,2.99 0.354,0.219 10 false SWR 2.469,2.573 2.698,2.74 0.229,0.167 10 false TC 1.583,1.042 1.885,1.219 0.302,0.177 10 false P23

Disconnect the P23 heater control connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
P23-10 (SWR) - P23-13 (TC) Seat heater LO switch OFF 10 kΩ or higher
Seat heater LO switch ON Below 1 Ω
P23-12 (HIR) - P23-13 (TC) Seat heater HI switch OFF 10 kΩ or higher
Seat heater HI switch ON Below 1 Ω
P23-13 (TC) - Body ground Always Below 1 Ω


If the result is not as specified, there may be a malfunction on the wire harness side.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
P23-1 (B1) - P23-13 (TC) Always 11 to 14 V


If the result is not as specified, there may be a malfunction on the wire harness side.


d.

Connect the P23 heater control connector.


e.
B188617E01
0.057,0.078 2.312,0.437 2.254,0.359 10 Component with harness connector: (Seat Heater Control)

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
1 - Body ground Ignition switch ON
Seat heater switch OFF
Below 1 V
Ignition switch ON
Seat heater LO or HI switch ON
11 to 14 V


HINT:
·

When the heater reaches the specified temperature, the power turns off.

·

If the result is not as specified, the seat heater control may have a malfunction.