Home › Vehicle Interior › SEAT › REAR NO. 2 SEAT ASSEMBLY(for Manual Seat Type RH Side)
RM27L0U _58 Vehicle Interior _049342 SEAT _0235883 REAR NO. 2 SEAT ASSEMBLY(for Manual Seat Type RH Side) A

SEAT  REAR NO. 2 SEAT ASSEMBLY(for Manual Seat Type RH Side)  REASSEMBLY  


CAUTION / NOTICE / HINT

NOTICE:

Wear protective gloves. Sharp areas on the parts may injure your hands.


PROCEDURE

Hide 71607 1.INSTALL REAR NO. 2 SEAT ROD SUB-ASSEMBLY

a.
B191244

Install the rear No. 2 seat rod sub-assembly with the 2 bolts.

Torque:
18 N*m (184 kgf*cm, 13 ft.*lbf)


Hide 79303A 2.INSTALL NO. 3 SEATBACK FRAME SUB-ASSEMBLY RH

a.
B191240

Install the No. 3 seatback frame sub-assembly RH with the 5 bolts.

Torque:
32 N*m (326 kgf*cm, 24 ft.*lbf)


Hide 72620D 3.INSTALL REAR NO. 1 SEAT LOCK CABLE ASSEMBLY

a.
B191238

Insert the rear No. 1 seat lock cable assembly through the No. 3 seatback frame sub-assembly RH.


b.

Insert and rotate the cable ends to connect them.


c.

Connect the 2 clamps.


d.

Attach the 3 cable ties to install the rear No. 1 seat lock cable assembly.


Hide 71879D 4.INSTALL REAR SEAT RECLINING COVER INNER LH

a.
B191236

Attach the claw.


b.

Install the rear seat reclining cover inner LH with the screw.


Hide 71878D 5.INSTALL REAR SEAT RECLINING COVER INNER RH

a.
B191235

Attach the claw.


b.

Install the rear seat reclining cover inner RH with the screw.


Hide 79023 6.INSTALL NO. 2 SEATBACK COVER SUB-ASSEMBLY RH

a.
B191232E03
1.438,2.427 0.74,2.927 true 1.938,2.823 1.688,3.771 false 1.458,2.333 2.385,2.521 0.927,0.188 10 false New Hog Ring 1.99,2.781 3.094,3.208 1.104,0.427 10 true Hog Ring Pliers

Using hog ring pliers, install the No. 2 seatback cover sub-assembly RH to the No. 2 seatback pad with new hog rings.

NOTICE:
·

Be careful not to damage the cover.

·

When installing the hog rings, avoid wrinkling the cover.




Hide 7.INSTALL SEATBACK COVER WITH PAD

a.
B191227

Attach the hooks to install the seatback cover with pad.


b.
B195219

Attach the hooks.


Hide 71931C 8.INSTALL REAR NO. 2 SEAT HEADREST SUPPORT ASSEMBLY

B290096

a.

Attach the 4 claws to install the 2 rear No. 2 seat headrest supports.


Hide 71701C 9.INSTALL REAR SEATBACK BOARD SUB-ASSEMBLY RH

a.
B292871

Attach the 9 clips to install the rear seatback board sub-assembly RH.


Hide 72067 10.INSTALL REAR BACK LOCK CONTROL LEVER SUB-ASSEMBLY RH

a.
B191220E02
3.146,0.365 3.25,0.521 0.104,0.156 10 false 1 3.094,0.875 3.198,1.083 0.104,0.208 10 true 2

Connect the rear No. 1 seat lock cable assembly to the rear back lock control lever sub-assembly RH in the order shown in the illustration.


b.

Install the rear back control lever sub-assembly RH with the screw.


Hide 72909 11.INSTALL REAR NO. 2 SEAT HANDLE

a.
B191219E02
2.99,1.135 3.125,1.302 0.135,0.167 10 true 1 2.99,0.583 3.125,0.74 0.135,0.156 10 true 2

Connect the rear No. 1 seat lock cable assembly to the rear No. 2 seat handle in the order shown in the illustration.


b.

Install the rear No. 2 seat handle with the 2 screws.


Hide 71970 12.INSTALL REAR SEAT HEADREST ASSEMBLY

B290080

a.

Install the rear seat headrest assembly.

NOTICE:
·

Make sure the rear seat headrest assembly is facing in the correct direction.

·

Push in the rear seat headrest assembly until the headrest lock engages.




Hide 72998 13.INSTALL REAR SEAT CUSHION COVER LH

a.
B191218

Attach the claw.


b.

Install the rear seat cushion cover LH with the screw.


Hide 72995C 14.INSTALL REAR SEAT CUSHION COVER OUTER RH

a.
B191217

Attach the claw.


b.

Install the rear seat cushion cover outer RH with the screw.


Hide 79021 15.INSTALL NO. 2 SEAT CUSHION COVER SUB-ASSEMBLY RH

a.

Using hog ring pliers, install the No. 2 seat cushion cover sub-assembly RH to the No. 2 seat cushion pad with new hog rings.

B443324E01
4.396,1.688 4.646,0.677 true 5.531,1.896 5.604,1.156 true 4.677,0.594 5.656,0.802 0.979,0.208 10 false New Hog Ring 5.677,1.021 6.656,1.458 0.979,0.438 10 true Hog Ring Pliers

NOTICE:
·

Be careful not to damage the cover.

·

When installing the hog rings, avoid wrinkling the cover.




Hide 79360A 16.INSTALL NO. 3 SEAT CUSHION SPRING ASSEMBLY RH

a.
B191214

Set the No. 3 seat cushion spring assembly RH in place.


b.

Attach the hooks.


c.
B191213E03
1.594,2.531 0.875,3.063 false 1.958,3 1.792,3.844 false 1.99,2.917 3.042,3.354 1.052,0.438 10 true Hog Ring Pliers 1.615,2.448 2.552,2.646 0.938,0.198 10 false New Hog Ring

Using hog ring pliers, install the No. 3 seat cushion spring assembly RH with new hog rings.

NOTICE:
·

Be careful not to damage the cover.

·

When installing the hog rings, avoid wrinkling the cover.




Hide 17.INSTALL REAR NO. 2 SEAT CUSHION ASSEMBLY RH

B191211

a.

Install the 2 bushes to the No. 3 seat cushion spring assembly RH. Then using a T45 "TORX" socket wrench, install the 2 "TORX" bolts.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)


b.

Install the rear No. 2 seat cushion assembly RH with the 2 bolts.

Torque:
32 N*m (326 kgf*cm, 24 ft.*lbf)


Hide 71692C 18.INSTALL REAR SEAT LOCK COVER INNER LH

a.
B191207

Attach the 3 claws.


b.

Install the rear seat lock cover inner LH with the screw.


Hide 71691B 19.INSTALL REAR SEAT LOCK COVER OUTER RH

a.
B191209

Attach the 2 claws.


b.

Install the rear seat lock cover outer RH with the screw.


Hide 73580A 20.INSTALL REAR NO. 2 SEAT INNER BELT SUB-ASSEMBLY