Wear protective gloves. Sharp areas on the parts may injure your hands.
73580A
1.REMOVE REAR NO. 2 SEAT INNER BELT SUB-ASSEMBLY
71692C
2.REMOVE REAR SEAT LOCK COVER INNER LH
Remove the screw.
Detach the 3 claws and remove the rear seat lock cover inner LH.
71691B
3.REMOVE REAR SEAT LOCK COVER OUTER RH
Remove the screw.
Detach the 2 claws and remove the rear seat lock cover outer RH.
4.REMOVE REAR NO. 2 SEAT CUSHION ASSEMBLY RH
Remove the 2 bolts.
Using a T45 "TORX" socket wrench, remove the 2 "TORX" bolts and 2 bushes. Then remove the rear No. 2 seat cushion assembly LH.
79360A
5.REMOVE NO. 3 SEAT CUSHION SPRING ASSEMBLY RH
Remove the hog rings.
Detach the hooks and No. 3 seat cushion spring assembly RH.
79021
6.REMOVE NO. 2 SEAT CUSHION COVER SUB-ASSEMBLY RH
Remove the hog rings and No. 2 seat cushion cover sub-assembly RH from the No. 2 seat cushion pad.
72998
7.REMOVE REAR SEAT CUSHION COVER LH
Remove the screw.
Detach the claw and remove the rear seat cushion cover LH.
72995C
8.REMOVE REAR SEAT CUSHION COVER OUTER RH
Remove the screw.
Detach the claw and remove the rear seat cushion cover outer RH.
71701C
9.REMOVE REAR SEATBACK BOARD SUB-ASSEMBLY RH
Detach the 9 clips and remove the rear seatback board sub-assembly RH.
71970
10.REMOVE REAR SEAT HEADREST ASSEMBLY
Detach the hook and disconnect the lower part of the No. 2 seatback cover sub-assembly RH.
Remove the cable clamp and disconnect the headrest cable from the No. 3 seatback frame sub-assembly RH.
Detach the cable clamp, twist the cable end in the direction indicated by the arrow and disconnect the headrest cable from the reclining control base RH.
Using a screwdriver, push in the headrest lock button to release the headrest lock.
Tape the screwdriver tip before use.
Pull up and remove the rear seat headrest assembly.
When removing the rear seat headrest assembly while it is in the vehicle, fold down the headrest before removing it so that it does not contact the roof.
71931C
11.REMOVE REAR NO. 2 SEAT HEADREST SUPPORT ASSEMBLY
Detach the 4 claws and remove the 2 rear No. 2 seat headrest supports.
12.REMOVE SEATBACK COVER WITH PAD
Detach the 2 wire harness clamps.
Detach the hooks and remove the seatback cover with pad.
79023
13.REMOVE NO. 2 SEATBACK COVER SUB-ASSEMBLY RH
Remove the hog rings and No. 2 seatback cover sub-assembly from the No. 2 seatback pad.
82195
14.REMOVE REAR NO. 2 SEAT WIRE RH
Disconnect the 3 connectors.
Detach the 4 wire harness clamps and remove the rear No. 2 seat wire RH.
72571A
15.REMOVE RECLINING CONTROL BASE RH
Remove the 2 nuts and reclining control base RH.
79303A
16.REMOVE NO. 3 SEATBACK FRAME SUB-ASSEMBLY RH
Remove the 3 bolts and No. 3 seatback frame sub-assembly RH.
85820X
17.REMOVE POWER SEAT MOTOR ASSEMBLY RH
Using a screwdriver, remove the 2 washers.
Using a screwdriver and hammer, lightly tap the reclining connecting pipe to remove it.
Remove the 3 bolts and power seat motor assembly RH.
85820Y
18.REMOVE POWER SEAT MOTOR ASSEMBLY LH
Remove the 3 bolts and power seat motor assembly LH.
71607
19.REMOVE REAR NO. 2 SEAT ROD SUB-ASSEMBLY
Remove the 2 bolts and rear No. 2 seat rod sub-assembly.