Home › Vehicle Interior › HEATING / AIR CONDITIONING › AIR CONDITIONING SYSTEM
RM27L0U _58 Vehicle Interior _049344 HEATING / AIR CONDITIONING _0235901 AIR CONDITIONING SYSTEM U

HEATING / AIR CONDITIONING  AIR CONDITIONING SYSTEM  TERMINALS OF ECU  


CHECK AIR CONDITIONING AMPLIFIER


U153933E02
3.865,0.344 4.167,0.521 0.302,0.177 10 false H24 1.667,0.344 1.969,0.521 0.302,0.177 10 false H67 5.521,0.333 5.781,0.51 0.26,0.177 10 false z13

a.

Disconnect the H24, H67 and z13 air conditioning amplifier connectors.


b.

Measure the voltage and resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
H24-1 (IG+) - Body ground P - Body ground Ignition power supply Ignition switch ON 11 to 14 V
Ignition switch off Below 1 V
H24-14 (GND) - Body ground W-B - Body ground Ground Always Below 1 Ω
H24-21 (B) - Body ground R - Body ground Battery power source Always 11 to 14 V
H67-20 (RGND) - Body ground W-B - Body ground Ground Always Below 1 Ω
H67-24 (+B2) - Body ground LG - Body ground Battery power source Always 11 to 14 V

If the result is not as specified, there may be a malfunction on the wire harness side.


c.

Reconnect the H24, H67 and z13 air conditioning amplifier connectors.


d.

Measure the voltage and resistance according to the value(s) in the table below.

HINT:

Check from the rear of the connector with it connected to the air conditioning amplifier.


Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
H24-5 (TAM) - H24-13 (SG-2) V - G A/C ambient temperature sensor signal Ignition switch ON at 25°C (77°F) 1.35 to 1.75 V
Ignition switch ON at 40°C (104°F) 0.9 to 1.2 V
H24-8 (LOCK) - H24-13 (SG-2) SB - G A/C compressor lock sensor signal Engine is running
Blower switch LO
A/C switch ON
Pulse generation
(see waveform 1)
H24-9 (PRE) - Body ground Y - Body ground A/C pressure sensor signal Refrigerant pressure: normal 0.5 to 4.8355 V
H24-10 (S5-3) - Body ground R - Body ground Power supply for pressure sensor Ignition switch ON 4.5 to 5.5 V
H24-11 (CANH) - H24-14 (GND) B - W-B Hi-level CAN bus line Ignition switch ON Pulse generation
(see waveform 2)
H24-12 (CANL) - H24-14 (GND) W - W-B Lo-level CAN bus line Ignition switch ON Pulse generation
(see waveform 3)
H24-13 (SG-2) - Body ground G - Body ground Ground for ambient temperature sensor Always Below 1 Ω
H24-17 (AC1) - H24-14 (GND) B - W-B Idle-up request signal Engine idling
Magnet Clutch is not engaged
11 to 14 V
Engine idling
Magnet Clutch is engaged
Below 1 V
H24-18 (MHTR) - H24-14 (GND) L - W-B Mirror heater relay drive signal Mirror heater switch OFF→ON 11 to 14 V → Below 1 V
H24-20 (MGC) - H24-14 (GND) P - W-B A/C compressor magnetic clutch operation signal Ignition switch ON
Blower switch LO
A/C switch OFF
11 to 14 V
Ignition switch ON
Blower switch LO
A/C switch ON
Below 1 V
H24-23 (BLW) - H24-14 (GND) LG - W-B Blower motor control signal Ignition switch ON
Blower switch LO
Pulse generation
(see waveform 4)
H24-27 (ACT) - H24-14 (GND) L - W-B A/C compressor magnetic clutch on permit signal Engine idling → Accelerator pedal depressed (Air conditioning cut signal output when engine load increases rapidly) 11 to 14 V → Below 2 V
H24-29 (TR) - H24-34 (SG-1) G - B Room temperature sensor signal Ignition switch ON
Front side interior temperature: 25°C (77°F)
1.8 to 2.2 V
H24-32 (TSP) - Body ground L - Body ground Passenger side solar sensor signal Ignition switch ON
Solar sensor subjected to electric light
0.8 to 4.3 V
H24-33 (TSD) - Body ground P - Body ground Driver side solar sensor signal Ignition switch ON
Solar sensor subjected to electric light
0.8 to 4.3 V
H24-34 (SG-1) - Body ground B - Body ground Ground for room temperature sensor Always Below 1 Ω
H24-37 (LIN1) - H24-14 (GND) SB - W-B LIN communication signal Ignition switch ON Pulse generation
H24-38 (RDEF) - H24-14 (GND) R - W-B Defogger relay drive signal Defogger switch OFF→ON 11 to 14 V → Below 1 V
H24-39 (CFN+) - H24-14 (GND) V - W-B Condenser fan relay drive signal Ignition switch ON
Condenser fan OFF→ON
11 to 14 V → Below 1 V
H24-40 (D) - H24-14 (GND) GR - W-B Deicer relay drive signal Deicer switch OFF→ON 11 to 14 V → Below 1 V
H67-1 (RBUS) - H67-21 (RBUG) V - G BUS IC control signal Ignition switch off → ON Pulse generation
H67-4 (TEC) - H67-19 (SGND) R - L Rear evaporator temperature sensor signal Ignition switch ON
Evaporator temperature at 0°C (32°F)
1.7 to 2.1 V
H67-6 (SG-5) - Body ground BR - Body ground Ground for seat blower switch Always Below 1 Ω
H67-7 (SG-6) - Body ground P - Body ground Ground for rear room temperature sensor Always Below 1 Ω
H67-8 (S5-2) - H67-6 (SG-5) SB - BR Power supply for seat blower switch Ignition switch ON 4.5 to 5.5 V
H67-9 (SHD+) - H67-20 (RGND) W - W-B Driver seat blower drive signal Ignition switch ON Pulse generation
H67-10 (SHP+) - H67-20 (RGND) BE - W-B Passenger seat blower drive signal Ignition switch ON Pulse generation
H67-13 (RLIN) - H67-20 (RGND) B - W-B LIN communication signal Ignition switch ON Pulse generation
H67-15 (AD-4) - H67-20 (RGND) GR - W-B Driver seat blower switch signal Ignition switch ON
Driver seat blower switch 0 position
4.5 to 5.5 V
Ignition switch ON
Driver seat blower switch 3 position
Below 1 V
H67-16 (AD-5) - H67-20 (RGND) W - W-B Passenger seat blower switch signal Ignition switch ON
Passenger seat blower switch 0 position
4.5 to 5.5 V
Ignition switch ON
Passenger seat blower switch 3 position
Below 1 V
H67-17 (TR) - H67-7 (SG-6) L - P Rear room temperature sensor signal Ignition switch ON
Rear side interior temperature: 25°C (77°F)
1.8 to 2.2 V
H67-19 (SGND) - Body ground L - Body ground Ground for rear evaporator temperature sensor Always Below 1 Ω
H67-21 (RBUG) - Body ground G - Body ground Ground for BUS IC Always Below 1 Ω
H67-22 (BLWH) - H67-20 (RGND) P - W-B Blower motor control signal Ignition switch ON
Blower switch LO
Pulse generation
(see waveform 5)
H67-23 (RBBU) - H67-21 (RBUG) Y - G Power supply for BUS IC Ignition switch off Below 1 V
Ignition switch ON 11 to 14 V
z13-2 (BUS G) - Body ground - Ground for BUS IC Always Below 1 Ω
z13-3 (BUS) - z13-2 (BUS G) - BUS IC control signal Ignition switch off → ON Pulse generation
z13-4 (B BUS) - z13-2 (BUS G) - Power supply for BUS IC Ignition switch off Below 1 V
z13-4 (B BUS) - z13-2 (BUS G) - Ignition switch ON 11 to 14 V
z13-5 (SGA) - Body ground - Ground for evaporator temperature sensor Always Below 1 Ω
z13-6 (TEA) - z13-5 (SGA) - A/C evaporator temperature sensor signal Ignition switch ON
Evaporator temperature at 0°C (32°F)
1.7 to 2.1 V
z13-6 (TEA) - z13-5 (SGA) - Ignition switch ON
Evaporator temperature at 15°C (59°F)
0.7 to 1.3 V

If the result is not as specified, the ECU may have a malfunction.



e.
E147483E01
2.91,0.901 3.243,1.043 0.332,0.142 10 GND 2.391,0 3.218,0.146 0.826,0.146 10 200 mV/DIV. 1.309,1.877 2.067,2.051 0.757,0.174 10 10 ms./DIV.

Waveform 1: Using an oscilloscope

Compressor Lock Signal
Terminal Name LOCK - SG-2
Tester Range 200 mV/DIV., 10 ms./DIV.
Condition Engine is running
Blower switch LO
A/C switch ON


f.
E344812E01
2.75,0.292 3.313,0.49 0.563,0.198 10 false 1 V/DIV. 2.99,1.396 3.406,1.594 0.417,0.198 10 false GND 1.594,1.865 2.49,2.094 0.896,0.229 10 false 10 μsec./DIV.

Waveform 2 (Reference) : Using an oscilloscope

CAN Communication Signal
Terminal Name CANH - GND
Tester Range 1 V/DIV., 10 μsec./DIV.
Condition Ignition switch ON

HINT:

The waveform varies depending on the CAN communication signal.



g.
E344813E01
3.031,1.375 3.396,1.583 0.365,0.208 10 false GND 2.76,0.292 3.302,0.5 0.542,0.208 10 false 1 V/DIV. 1.677,1.875 2.583,2.083 0.906,0.208 10 false 10 μsec./DIV.

Waveform 3 (Reference) : Using an oscilloscope

CAN Communication Signal
Terminal Name CANL - GND
Tester Range 1 V/DIV., 10 μsec./DIV.
Condition Ignition switch ON

HINT:

The waveform varies depending on the CAN communication signal.



h.
E103396E08
2.931,1.611 3.305,1.792 0.374,0.181 10 GND 2.737,0.259 3.273,0.456 0.536,0.198 10 1 V/DIV. 1.06,1.926 2.123,2.100 1.062,0.174 10 500 μsec./DIV.

Waveform 4 : Using an oscilloscope

Blower Motor Control Signal
Terminal Name BLW - GND
Tester Range 1 V/DIV., 500 μsec./DIV.
Condition Ignition switch ON
Blower switch LO

HINT:

When the blower level is increased, the duty ratio changes accordingly.



i.
E103396E08
2.931,1.611 3.305,1.792 0.374,0.181 10 GND 2.737,0.259 3.273,0.456 0.536,0.198 10 1 V/DIV. 1.06,1.926 2.123,2.100 1.062,0.174 10 500 μsec./DIV.

Waveform 5 : Using an oscilloscope

Blower Motor Control Signal
Terminal Name BLWH - RGND
Tester Range 1 V/DIV., 500 μsec./DIV.
Condition Ignition switch ON
Blower switch LO

HINT:

When the blower level is increased, the duty ratio changes accordingly.




CHECK INTEGRATION CONTROL AND PANEL


U153164E02
3.396,0.198 3.677,0.375 0.281,0.177 10 false H45

a.

Disconnect the H45 integration control and panel connector.


b.

Measure the voltage and resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
H45-16 (IG+) - H45-1 (GND) P - W-B Ignition power supply Ignition switch ON 11 to 14 V
Ignition switch off Below 1 V
H45-1 (GND) - Body ground W-B - Body ground Ground Always Below 1 Ω

If the result is not as specified, there may be a malfunction on the wire harness side.



c.

Reconnect the H45 integration control and panel connector.

Measure the voltage according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
H45-3 (STX) - H45-1 (GND) SB - W-B LIN communication signal Ignition switch ON Pulse generation

If the result is not as specified, the integration control and panel may have a malfunction.




CHECK AIR CONDITIONING CONTROL PANEL


U154052E02
3.396,0.094 3.604,0.24 0.208,0.146 10 false S4

a.

Disconnect the S4 air conditioning control panel connector.


b.

Measure the voltage and resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
S4-1 (IG) - S4-4 (E) P - W-B Ignition power supply Ignition switch ON 11 to 14 V
Ignition switch off Below 1 V
S4-4 (E) - Body ground W-B - Body ground Ground Always Below 1 Ω

If the result is not as specified, there may be a malfunction on the wire harness side.



c.

Reconnect the S4 air conditioning control panel connector.


d.

Measure the voltage according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
S4-5 (RLIN) - S4-4 (E) GR - W-B LIN communication signal Ignition switch ON Pulse generation

If the result is not as specified, the air conditioning control panel may have a malfunction.