Home › Vehicle Interior › HEATING / AIR CONDITIONING › AIR CONDITIONING SYSTEM
RM27L0U _58 Vehicle Interior _049344 HEATING / AIR CONDITIONING _0235901 AIR CONDITIONING SYSTEM D

HEATING / AIR CONDITIONING  AIR CONDITIONING SYSTEM  CHECK MODE PROCEDURE  


PANEL DIAGNOSIS (INDICATOR CHECK)


a.

Turn the ignition switch off.


b.
E157839

Press and hold the A/C control AUTO switch and Recirculation/Fresh switch simultaneously, and turn the ignition switch to ON. Continue holding the 2 switches until the panel diagnosis mode begins.


c.
E127586E01
0.712,0.34 1.292,0.522 0.581,0.181 10 1 second 1.744,0.34 2.324,0.522 0.581,0.181 10 1 second 0.186,0.974 0.412,1.155 0.225,0.181 10 ON 0.186,1.418 0.481,1.599 0.295,0.181 10 OFF

Check that all indicators and the display area are turned on and off 4 times in succession at 1 second intervals.

E157840E01
0.495,0.343 2.393,0.521 1.897,0.178 10 Air Conditioning Control Panel 4.298,0.025 6.153,0.203 1.855,0.178 10 Integration Control and Panel

HINT:

After the indicator check is completed, the system automatically enters sensor check mode.



d.

Press the OFF switch to terminate the panel diagnosis.



PANEL DIAGNOSIS (SENSOR CHECK)


a.

Perform the indicator check.

HINT:

After the indicator check is completed, the system automatically enters sensor check mode.



b.

Press the REC/FRS switch to enter actuator check mode.


c.

After the actuator check is completed, press the AUTO switch to enter sensor check mode.

NOTICE:

The sensor check must be performed again after the actuator check is completed because sensor check mode, which starts automatically after the indicator check, cannot fully detect malfunctions.



d.
E157841

Check the sensor check results displayed on the set temperature display.

Result Code Display
Present malfunction Blinks
Past malfunction Blinks

HINT:
·

The illustration shows the display when code 21 is output.

·

When 2 or more sensor check codes are detected, the codes are displayed in ascending numerical order.

·

In cases with 2 or more codes, if they are difficult to read, press the DEF switch to activate the step operation and display them one by one.

·

The codes are displayed in ascending numerical order as the DEF switch is pressed.




e.

When any sensor check codes are displayed, refer to the DTC Chart (See page Vehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING SYSTEM>DIAGNOSTIC TROUBLE CODE CHART).


f.

Press the OFF switch to terminate the panel diagnosis.

HINT:

Pressing the REC/FRS switch returns the system to actuator check mode.




PANEL DIAGNOSIS (CLEAR SENSOR CHECK CODE)


a.

Inspect and repair or replace the malfunctioning parts.


b.
E157842

Clear the sensor check codes.

i.

While pressing the Fr DEF switch during sensor check mode, press the Rr DEF switch.

HINT:

Sensor check codes can be cleared by removing the A/C fuse from the main body ECU for more than 60 seconds.




c.

Perform the sensor check and confirm that normal code 00 is displayed.



PANEL DIAGNOSIS (ACTUATOR CHECK)


E127586E01
0.712,0.34 1.292,0.522 0.581,0.181 10 1 second 1.744,0.34 2.324,0.522 0.581,0.181 10 1 second 0.186,0.974 0.412,1.155 0.225,0.181 10 ON 0.186,1.418 0.481,1.599 0.295,0.181 10 OFF

a.

Start the engine and warm it up.


b.

Perform the indicator check.


c.

When the sensor check is started after the indicator check, press the REC/FRS switch to start the actuator check.

HINT:

Perform the actuator check with the engine running.



d.

Check the temperature and blower levels by hand at each step while the actuator check proceeds from step 0 to 9 at 1 second intervals (continuous operation).

E157843E01
0.488,0.368 2.390,0.530 1.902,0.162 10 Air Conditioning Control Panel 4.349,0.079 6.225,0.241 1.876,0.162 10 Integration Control and Panel

HINT:

Each step number is displayed on the set temperature display.



e.

To display step numbers one by one manually, press the Fr DEF switch to activate the step operation. The step number changes each time the Fr DEF switch is pressed.

HINT:
·

Each step number blinks at 1 second intervals during the step operation.

·

The illustration shows the display when step number 5 is displayed.




f.

Press the OFF switch to terminate the panel diagnosis.

HINT:

Pressing the AUTO switch returns to sensor check mode.


Step No.
(Front display)
Blower Level Front Air Mix Damper Air Flow Vent Air Inlet Damper Cool Air Bypass Compres-
sor
Rear Air Mix Damper Rear Air Flow Vent Rear Blower Level
0 0 0%
(MAX COLD)
FACE FRESH 0% OFF 0 Rr FACE 0
1 1 0%
(MAX COLD)
FACE FRESH 0% OFF 0 Rr FACE 1
2 17 0%
(MAX COLD)
FACE RECIRCULATION / FRESH 0% ON 0 Rr FACE 17
3 17 0%
(MAX COLD)
FACE RECIRCULATION 100% ON 0 Rr FACE 17
4 17 50% BI-LEVEL RECIRCULATION 100% ON 50 Rr BI-LEVEL 17
5 17 50% BI-LEVEL RECIRCULATION 100% ON 50 Rr BI-LEVEL 17
6 17 50% FOOT FRESH 100% ON 50 Rr FOOT 17
7 17 100%
(MAX HOT)
FOOT FRESH 100% ON 100 Rr FOOT 17
8 17 100%
(MAX HOT)
FOOT/DEF FRESH 100% ON 100 Rr FOOT 17
9 31 100%
(MAX HOT)
DEF FRESH 100% ON 100 Rr FOOT 31