Home › Vehicle Interior › HEATING / AIR CONDITIONING › REAR AIR CONDITIONING UNIT
RM27L0U _58 Vehicle Interior _049344 HEATING / AIR CONDITIONING _0235909 REAR AIR CONDITIONING UNIT A

HEATING / AIR CONDITIONING  REAR AIR CONDITIONING UNIT  REASSEMBLY  


PROCEDURE

Hide 88501R 1.INSTALL REAR EVAPORATOR SUB-ASSEMBLY

a.
E150109

Sufficiently apply compressor oil to 2 new O-rings and the fitting surfaces.

Compressor oil:

ND-OIL 8 or equivalent



b.

Install the 2 O-rings to the rear evaporator.


c.
I104331

Install the rear evaporator as shown in the illustration.

HINT:

If a new rear evaporator is installed, add compressor oil to the rear evaporator as follows.


Compressor oil:

ND-OIL8 or equivalent. Add 40 cc (1.35 fl. oz.)



d.
I104329

Install the 13 screws.


Hide 2.INSTALL REAR EVAPORATOR TEMPERATURE SENSOR

a.
I104328

Attach the claw and install the rear evaporator temperature sensor.


b.

Attach the clamp to the rear cooling unit.


Hide 88515B 3.INSTALL REAR COOLING UNIT EXPANSION VALVE

a.
E150105

Using a 4 mm hexagon wrench, install the rear cooling unit expansion valve with the 2 hexagon bolts.

Torque:
3.5 N*m (36 kgf*cm, 31 in.*lbf)


b.
I104327

Install the grommet.


c.
I104326

Attach the 3 claws and install the plate.


Hide 87165C 4.INSTALL BLOWER MOTOR CONTROL

a.
I104325

Install the blower motor controller with the 2 screws.


Hide 87103D 5.INSTALL REAR BLOWER MOTOR SUB-ASSEMBLY

a.
I104324

Install the rear blower motor with the 3 screws.


Hide 87107B 6.INSTALL HEATER RADIATOR UNIT SUB-ASSEMBLY

a.
E183891

Install the heater radiator unit as shown in the illustration.


b.
E183889

Attach the claw and install the heater clamp.


c.

Install the heater clamp with the screw.


Hide 87246 7.INSTALL HEATER WATER OUTLET HOSE

a.
E183888

Using pliers, grip the claws of the clip and slide the clips to connect the heater water hose.


Hide 87245 8.INSTALL HEATER WATER INLET HOSE

a.
E183887

Using pliers, grip the claws of the clip and slide the clips to connect the heater water hose.


Hide 87248 9.INSTALL WATER PIPE SUB-ASSEMBLY

E183739

a.

Using pliers, grip the claws of the 2 clips and slide the clips to install the water pipe.


b.
I104317

Install the bracket with the 4 screws.


Hide 88710J 10.INSTALL AIRCONDITIONER CONNECTOR TUBE

a.

Sufficiently apply compressor oil to 2 new O-rings and the fitting surfaces of the air conditioning connector tube.

Compressor oil:

ND-OIL 8 or equivalent



b.
I104316

Install the 2 new O-rings on the air conditioning connector tube.


c.
I104315

Move the hook connector in the direction indicated by the arrow in the illustration.


d.

Insert the pipe joint into the fitting hole securely and tighten the bolt.

Torque:
9.8 N*m (100 kgf*cm, 87 in.*lbf)


e.
I104313

Install the air conditioning connector tube with the 3 screws.


f.

Connect the hose.


g.
I104312

Install the packing.


Hide 87106X 11.INSTALL REAR MODE DAMPER SERVO MOTOR SUB-ASSEMBLY

a.
I104311E02
2.115,2.573 1.302,2.396 false 3.094,1.771 2.917,0.635 false 2.156,0.542 2.865,1.052 0.708,0.51 10 true Reference Point 0.583,2.302 1.26,2.615 0.677,0.313 10 false Reference Point

Using the reference point, install the rear mode damper servo motor with the 2 screws.


b.

Connect the connector.


c.
E191234

Install the bracket with the 4 screws.


Hide 87106W 12.INSTALL REAR AIR MIX DAMPER SERVO MOTOR SUB-ASSEMBLY

a.
I104308E01
2.616,1.8 3.288,2.119 0.672,0.319 10 Reference Point 1.357,2.001 2.566,1.898 2.566,1.898 2.087,2.692 false

Using the reference point, install the rear air mix control servo motor with the 2 screws.


b.

Connect the connector.