Home › Vehicle Exterior › WINDOW / GLASS › POWER WINDOW CONTROL SYSTEM
RM27L0U _59 Vehicle Exterior _049347 WINDOW / GLASS _0235939 POWER WINDOW CONTROL SYSTEM U

WINDOW / GLASS  POWER WINDOW CONTROL SYSTEM  TERMINALS OF ECU  


CHECK FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH


U153386E02
3.479,0.24 3.688,0.417 0.208,0.177 10 false M3

a.

Disconnect the M3 power window regulator motor LH connector.


b.

Measure the resistance and voltage according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
M3-2 (B) - Body ground G - Body ground Battery power supply Always 11 to 14 V
M3-1 (GND) - Body ground W-B - Body ground Ground Always Below 1 Ω

If the result is not as specified, there may be a malfunction on the wire harness side.


c.

Reconnect the M3 power window regulator motor LH connector.


d.

Measure the voltage according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
M3-10 (UP) - M3-1 (GND) BE - W-B Power window UP operation Ignition switch ON
Power window regulator master switch
OFF → UP
11 to 14 V → Below 1 V
M3-10 (UP) - M3-1 (GND) BE - W-B Power window UP operation Ignition switch ON
door glass fully open → power window AUTO UP operation → the door glass fully closed
11 to 14 V → Below 1 V → 11 to 14 V
M3-7 (DOWN) - M3-1 (GND) LG - W-B Power window DOWN operation Ignition switch ON
Power window regulator master switch
OFF → DOWN
11 to 14 V → Below 1 V
M3-7 (DOWN) - M3-1 (GND) LG - W-B Power window DOWN operation Ignition switch ON
door glass fully closed → power window AUTO DOWN operation → the door glass fully closed
11 to 14 V → Below 1 V → 11 to 14 V
M3-9 (LIN) - M3-1 (GND) W - W-B LIN communication signal Ignition switch ON Pulse generation



CHECK FRONT POWER WINDOW REGULATOR MOTOR RH


U153387E02
3.51,0.198 3.677,0.375 0.167,0.177 10 false L3

a.

Disconnect the L3 power window regulator motor RH connector.


b.

Measure the resistance and voltage according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
L3-2 (B) - Body ground V - Body ground Battery power supply Always 11 to 14 V
L3-1 (GND) - Body ground W-B - Body ground Ground Always Below 1 Ω

If the result is not as specified, there may be a malfunction on the wire harness side.


c.

Reconnect the L3 power window regulator motor RH connector.


d.

Measure the voltage according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
L3-10 (UP) - L3-1 (GND) G - W-B Power window UP operation Ignition switch ON
power window regulator switch
OFF → UP
11 to 14 V → Below 1 V
L3-10 (UP) - L3-1 (GND) G - W-B Power window UP operation Ignition switch ON
door glass fully open → power window AUTO UP operation → the door glass fully closed
11 to 14 V → Below 1 V → 11 to 14 V
L3-7 (DOWN) - L3-1 (GND) P - W-B Power window DOWN operation Ignition switch ON
power window regulator switch
OFF → DOWN
11 to 14 V → Below 1 V
L3-7 (DOWN) - L3-1 (GND) P - W-B Power window DOWN operation Ignition switch ON
door glass fully closed → power window AUTO DOWN operation → the door glass fully closed
11 to 14 V → Below 1 V → 11 to 14 V
L3-9 (LIN) - L3-1 (GND) L - W-B LIN communication signal Ignition switch ON Pulse generation
L3-4 (AUTO) - L3-1 (GND) B - W-B Power window AUTO UP/DOWN operation Ignition switch ON
power window regulator switch
OFF → AUTO UP/DOWN operation
11 to 14 V → Below 1 V



CHECK POWER WINDOW REGULATOR MASTER SWITCH


B443129E01
3.302,0.188 3.698,0.406 0.396,0.219 3.406,0.208 3.635,0.385 0.229,0.177 10 false M2

a.

Disconnect the M2 power window regulator master switch connector.


b.

Measure the resistance and voltage according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
M2-3 (B) - Body ground L - Body ground Battery power supply Ignition switch ON 11 to 14 V
M2-13 (B) - Body ground P - Body ground Battery power supply Always 11 to 14 V
M2-1 (E) - Body ground W-B - Body ground Ground Always Below 1 Ω

If the result is not as specified, there may be a malfunction on the wire harness side.


c.

Reconnect the M2 power window regulator master switch connector.


d.

Measure the voltage according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
M2-4 (UP) - M2-1 (E) BE - W-B Driver side door power window UP operation Ignition switch ON, driver side door power window regulator switch OFF → UP 11 to 14 V → Below 1 V
M2-4 (UP) - M2-1 (E) BE - W-B Driver side door power window AUTO UP operation Ignition switch ON, driver side door glass fully closed → power window AUTO UP operation → driver side door glass fully open 11 to 14 V → Below 1 V → 11 to 14 V
M2-5 (DOWN) - M2-1 (E) LG - W-B Driver side door power window DOWN operation Ignition switch ON, driver side door power window regulator switch OFF → DOWN 11 to 14 V → Below 1 V
M2-5 (DOWN) - M2-1 (E) LG - W-B Driver side door power window AUTO DOWN operation Ignition switch ON, driver side door glass fully closed → power window AUTO DOWN operation → driver side door glass fully open 11 to 14 V → Below 1 V → 11 to 14 V
M2-12 (U) - M2-1 (E) V - W-B Rear LH side door power window UP operation Ignition switch ON, rear LH side door power window regulator switch OFF → UP Below 1 V → 11 to 14 V
M2-15 (D) - M2-1 (E) B - W-B Rear LH side door power window DOWN operation Ignition switch ON, rear LH side door power window regulator switch OFF → DOWN Below 1 V → 11 to 14 V
M2-10 (U) - M2-1 (E) BE - W-B Rear RH side door power window UP operation Ignition switch ON, rear RH side door power window regulator switch OFF → UP Below 1 V → 11 to 14 V
M2-16 (D) - M2-1 (E) LG - W-B Rear RH side door power window DOWN operation Ignition switch ON, rear RH side door power window regulator switch OFF → DOWN Below 1 V → 11 to 14 V
M2-6 (LIN1) - M2-1 (E) L - W-B LIN communication signal Ignition switch ON Pulse generation
M2-7 (LIN2) - M2-1 (E) W - W-B LIN communication signal Ignition switch ON Pulse generation



CHECK MAIN BODY ECU (COWL SIDE JUNCTION BLOCK LH)


B443132E01
0.99,3.615 1.302,3.844 0.313,0.229 3.021,3.604 3.333,3.833 0.313,0.229 5.552,3.615 5.865,3.844 0.313,0.229 1.531,5.167 1.844,5.396 0.313,0.229 4.271,5.198 4.583,5.427 0.313,0.229 6,5.063 6.313,5.292 0.313,0.229 0.979,6.979 1.292,7.208 0.313,0.229 3.427,6.948 3.74,7.177 0.313,0.229 5.917,6.958 6.229,7.188 0.313,0.229 1.938,1.25 2.177,1.417 0.24,0.167 10 false DC 1.927,2.094 2.167,2.26 0.24,0.167 10 false DB 2.281,1.26 2.458,1.417 0.177,0.156 8 false H4 2.302,1.708 2.479,1.865 0.177,0.156 8 false H3 2.313,2.073 2.49,2.229 0.177,0.156 8 false H2 2.313,2.313 2.49,2.469 0.177,0.156 8 false H1 2.208,2.802 2.448,2.969 0.24,0.167 10 false DA 4.906,1.698 5.146,1.865 0.24,0.167 10 false DD 1.042,3.646 1.281,3.813 0.24,0.167 10 false DA 1.104,4.323 1.219,4.51 0.115,0.188 10 false 1 3.073,3.625 3.313,3.792 0.24,0.167 10 false DB 5.604,3.646 5.844,3.813 0.24,0.167 10 false DC 1.583,5.198 1.823,5.365 0.24,0.167 10 false DD 4.927,0.885 5.104,1.042 0.177,0.156 8 false DE 4.323,5.219 4.563,5.385 0.24,0.167 10 false DE 6.052,5.094 6.292,5.26 0.24,0.167 10 false H1 1.042,7.01 1.281,7.177 0.24,0.167 10 false H2 3.49,6.969 3.729,7.135 0.24,0.167 10 false H3 5.99,6.99 6.229,7.156 0.24,0.167 10 false H4

a.

Disconnect the DA, DB, DD, H2, H3 and H4 main body ECU connectors.


b.

Measure the resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
DD-62 (GND1, GND2) - Body ground W-B - Body ground Body ground Always Below 1 Ω
H3-21 (PCTY) - Body ground BE - Body ground Front door courtesy light switch RH signal Front door RH open → closed Below 1 Ω → 10 kΩ or higher
H4-24 (DCTY) - Body ground BR - Body ground Front door courtesy light switch LH signal Front door LH open → closed Below 1 Ω → 10 kΩ or higher

If the result is not as specified, there may be a malfunction on the wire harness side.


c.

Reconnect the DA, DB, DD, H2, H3 and H4 main body ECU connectors.


d.

Measure the voltage according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
DB-13 (BECU) - Body ground GR - Body ground BECU power supply Always 11 to 14 V
DA-1 (IG) - Body ground B - Body ground IG signal Always 11 to 14 V
H2-10 (LIN2) - DD-62 (GND1, GND2) V - W-B LIN communication signal Ignition switch ON Pulse generation

If the result is not as specified, there may be a malfunction on the wire harness side.



CHECK BACK DOOR ECU (MULTIPLEX BODY ECU)


U154019E03
1.833,0.354 2.052,0.521 0.219,0.167 10 false V2 3.896,0.354 4.115,0.521 0.219,0.167 10 false V3

a.

Disconnect the V2 and V3 back door ECU connectors.


b.

Measure the resistance and voltage according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
V2-7 (BECU) - Body ground GR - Body ground Battery power supply Always 11 to 14 V
V2-8 (SIG) - Body ground Y - Body ground IG power supply Ignition switch off Below 1 V
Ignition switch ON 11 to 14 V
V2-6 (GND) - Body ground W-B - Body ground Ground Always Below 1 Ω
V3-7 (BKUL) - V3-19 (KEYE) LG - BE Back door key cylinder linked switch signal Back door key cylinder turned UNLOCK Below 1 Ω
V3-8 (BKL) - V3-19 (KEYE) G - BE Back door key cylinder linked switch signal Back door key cylinder turned LOCK Below 1 Ω
V3-17 (P) - V3-25 (SGND) V - G Rear wiper retractable position switch signal Rear wiper motor retractable position Below 1 Ω

If the result is not as specified, there may be a malfunction on the wire harness side.


c.

Reconnect the V2 and V3 back door ECU connectors.


d.

Measure the resistance and voltage according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
V2-16 (MPX1) - V2-6 (GND) Y - W-B LIN communication signal Ignition switch ON Pulse generation
V2-21 (A UP) - V2-6 (GND) G - W-B Back door power window AUTO UP signal Ignition switch ON
Back door power window switch
OFF → AUTO UP
Pulse generation → Below 1 V
V2-22 (BUP) - V2-6 (GND) BE - W-B Back door power window UP signal Ignition switch ON
Back door power window switch
OFF → UP
Pulse generation → Below 1 V
V2-23 (BDN) - V2-6 (GND) V - W-B Back door power window DOWN signal Ignition switch ON
Back door power window switch
OFF → DOWN
Pulse generation → Below 1 V
V2-24 (A DN) - V2-6 (GND) L - W-B Back door power window AUTO DOWN signal Ignition switch ON
Back door power window switch
OFF → AUTO DOWN
Pulse generation → Below 1 V
V3-5 (BDUP) - V2-6 (GND) BE - W-B Back door power window UP operation signal Ignition switch ON
Back door power window switch
OFF → UP
Below 1 V → 11 to 14 V
V3-6 (BDDN) - V2-6 (GND) P - W-B Back door power window DOWN operation signal Ignition switch ON
Back door power window switch
OFF → DOWN
Below 1 V → 11 to 14 V
V3-12 (DSV) - V3-23 (DSG) LG - SB Power supply for Hall-IC Ignition switch ON 8.5 to 16 V
V3-13 (DS1) - V3-23 (DSG) L - SB Back door window glass position signal Back door power window operation Pulse generation
V3-14 (DS2) - V3-23 (DSG) Y - SB Back door window glass position signal Back door power window operation Pulse generation
V3-19 (KEYE) - V2-6 (GND) BE - W-B Ground for back door key cylinder switch Always Below 1 Ω
V3-23 (DSG) - V2-6 (GND) SB - W-B Ground for Hall-IC Always Below 1 Ω
V3-25 (SGND) - V2-6 (GND) G - W-B Ground for rear wiper reverse position and rear wiper retractable position switch Always Below 1 Ω