Home › Vehicle Exterior › WINDOW / GLASS › POWER WINDOW CONTROL SYSTEM
RM27L0U _59 Vehicle Exterior _049347 WINDOW / GLASS _0235939 POWER WINDOW CONTROL SYSTEM J

WINDOW / GLASS  POWER WINDOW CONTROL SYSTEM  Rear Power Window RH does not Operate with Rear Power Window Switch RH  


DESCRIPTION

If the rear RH side manual UP/DOWN function does not operate, there may be a malfunction in the rear power window regulator switch RH, the rear power window regulator motor RH, the power window regulator master switch, the harness and connector.


WIRING DIAGRAM

B219836E02
0.038,0.168 1.581,0.648 1.543,0.479 10 from Main Body ECU (P/W Relay) 0.518,1.538 1.569,1.697 1.051,0.159 10 from Battery 1.696,0.999 1.873,1.162 0.177,0.163 10 13 1.966,1.116 2.093,1.266 0.127,0.150 10 B 1.966,1.545 2.093,1.695 0.127,0.150 10 B 1.749,1.432 1.849,1.596 0.099,0.163 10 3 1.777,1.986 1.885,2.149 0.108,0.163 10 1 1.966,2.131 2.098,2.295 0.131,0.163 10 E 2.526,0.933 2.666,1.087 0.141,0.154 10 U 2.742,0.808 2.933,0.971 0.191,0.163 10 10 2.53,1.763 2.666,1.908 0.136,0.145 10 D 2.752,1.648 2.952,1.793 0.200,0.145 10 16 1.4,2.712 3.009,3.045 1.609,0.333 10 Power Window Regulator Master Switch Assembly 3.596,0.171 3.706,0.331 0.111,0.160 10 3 3.801,0.274 3.928,0.429 0.127,0.155 10 B 3.593,0.816 3.709,0.987 0.116,0.171 10 5 3.795,0.943 4.033,1.098 0.237,0.155 10 SU 3.585,1.682 3.695,1.834 0.110,0.152 10 2 3.804,1.774 4.019,1.945 0.215,0.171 10 SD 4.403,0.937 4.544,1.091 0.141,0.154 10 U 4.408,1.754 4.544,1.899 0.136,0.145 10 D 4.658,0.807 4.776,0.979 0.118,0.172 10 4 4.688,1.653 4.804,1.807 0.116,0.154 10 1 5.581,0.83 5.691,0.982 0.110,0.152 10 2 5.585,1.64 5.701,1.794 0.116,0.154 10 1 3.544,2.71 4.853,3.220 1.309,0.510 10 Rear Power Window Regulator Switch Assembly RH 5.677,2.428 6.977,2.955 1.299,0.527 10 Rear Power Window Regulator Motor Assembly RH 1.4,2.537 1.646,2.679 0.246,0.142 10 M2 3.544,2.519 3.818,2.695 0.274,0.176 10 N3 5.677,2.235 6.028,2.393 0.351,0.158 10 N4

PROCEDURE

1.CHECK HARNESS AND CONNECTOR (REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY RH - BATTERY)
a.
U153161E02
1.667,1.958 2.021,2.313 true 0.125,0.104 2.396,0.635 2.271,0.531 10 false Front view of wire harness connector: (to Rear Power Window Regulator Switch Assembly RH) 0.781,1.75 1,1.906 0.219,0.156 10 false N3 2.083,2.26 2.229,2.427 0.146,0.167 10 false B

Disconnect the N3 rear power window regulator switch RH connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
N3-3 (B) - Body ground Ignition switch ON 11 to 14 V




OK

2.INSPECT REAR POWER WINDOW REGULATOR SWITCH RH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.INSPECT REAR POWER WINDOW REGULATOR SWITCH RH
a.
B166141E05
0.039,0.055 2.799,0.582 2.760,0.528 10 Component without harness connected: (Rear Power Window Regulator Switch Assembly RH) 0.76,2.385 1.087,2.564 0.327,0.179 10 SU 1.26,2.479 1.455,2.658 0.195,0.179 10 U 1.737,2.479 1.915,2.658 0.177,0.179 10 B 2.176,2.491 2.435,2.670 0.259,0.179 10 SD 2.693,2.385 2.870,2.564 0.177,0.179 10 D 1.503,2.072 1.009,2.373 false 1.726,2.072 1.396,2.45 false 1.933,2.072 1.829,2.45 false 2.096,2.072 2.29,2.45 false 2.304,2.072 2.695,2.378 false

Remove the rear power window regulator switch RH (See page Vehicle Exterior>WINDOW / GLASS>REAR POWER WINDOW SWITCH>REMOVAL).


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
4 (U) - 3 (B) UP Below 1 Ω
1 (D) - 2 (SD) UP Below 1 Ω
4 (U) - 5 (SU) OFF Below 1 Ω
1 (D) - 2 (SD) OFF Below 1 Ω
4 (U) - 5 (SU) DOWN Below 1 Ω
1 (D) - 3 (B) DOWN Below 1 Ω




OK

3.CHECK HARNESS AND CONNECTOR (REAR POWER WINDOW SWITCH RH - REAR POWER WINDOW MOTOR RH)

NG

REPLACE REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY RH

3.CHECK HARNESS AND CONNECTOR (REAR POWER WINDOW SWITCH RH - REAR POWER WINDOW MOTOR RH)
a.
U153250E02
0.885,2.115 1.354,1.99 false 1.885,2 2.521,2.135 false 0.188,0 2.573,0.51 2.385,0.51 10 false Front view of wire harness connector: (to Rear Power Window Regulator Switch Assembly RH) 2.573,2.052 2.708,2.219 0.135,0.167 10 false U 0.74,2.042 0.865,2.198 0.125,0.156 10 false D 0.104,2.302 2.458,2.823 2.354,0.521 10 false Front view of wire harness connector: (to Power Window Regulator Motor Assembly RH) 0.385,1.646 0.583,1.813 0.198,0.167 10 false N3 0.448,3.844 0.646,4.01 0.198,0.167 10 false N4

Disconnect the N3 rear power window regulator switch RH connector.


b.

Disconnect the N4 rear power window regulator motor RH connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
N3-1 (D) - N4-1 Always Below 1 Ω
N3-4 (U) - N4-2 Always Below 1 Ω
N3-1 (D) - Body ground Always 10 kΩ or higher
N3-4 (U) - Body ground Always 10 kΩ or higher




OK

4.INSPECT REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY RH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.INSPECT REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY RH
B195595E01
0.057,0.017 2.537,0.541 2.479,0.524 10 Component without harness connected: (Rear power window regulator motor assembly RH) 1.536,2.93 2.259,3.110 0.723,0.180 10 Clockwise 2.365,2.414 3.070,2.739 0.705,0.325 10 Counterclockwise

a.

Remove the rear power window regulator motor RH (See page Vehicle Exterior>WINDOW / GLASS>REAR POWER WINDOW SWITCH>REMOVAL).


b.

Apply battery voltage and check that the motor gear rotates smoothly as follows.

OK:
Measurement Condition Specified Condition
Battery positive (+) → 1
Battery negative (-) → 2
Motor gear rotates counterclockwise
Battery positive (+) → 2
Battery negative (-) → 1
Motor gear rotates clockwise




OK

5.CHECK HARNESS AND CONNECTOR (POWER WINDOW MASTER SWITCH - REAR POWER WINDOW SWITCH RH)

NG

REPLACE REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY RH

5.CHECK HARNESS AND CONNECTOR (POWER WINDOW MASTER SWITCH - REAR POWER WINDOW SWITCH RH)
a.
U153252E01
0.083,0 2.509,0.489 2.426,0.489 10 Front view of wire harness connector: (to Power Window Regulator Master Switch Assembly) 0.117,2.481 2.544,2.970 2.426,0.489 10 Front view of wire harness connector: (to Rear Power Window Regulator Switch Assembly LH) 0.46,2.105 0.596,2.269 0.136,0.164 10 U 2.878,2.178 3.041,2.342 0.163,0.164 10 D 0.654,2.175 0.955,2.097 false 2.077,2.148 2.809,2.26 false 2.59,4.285 2.834,4.449 0.244,0.164 10 SU 0.575,4.279 0.815,4.442 0.240,0.164 10 SD 0.851,4.373 1.546,4.348 false 2.012,4.353 2.538,4.382 false 0.235,1.628 0.475,1.779 0.240,0.150 10 M2 0.356,3.909 0.666,4.059 0.310,0.150 10 N3

Disconnect the M2 power window regulator master switch connector.


b.

Disconnect the N3 rear power window regulator switch RH connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M2-10 (U) - N3-5 (SU) Always Below 1 Ω
M2-16 (D) - N3-2 (SD) Always Below 1 Ω
M2-10 (U) - Body ground Always 10 kΩ or higher
M2-16 (D) - Body ground Always 10 kΩ or higher




OK

REPLACE POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR