Home › Vehicle Exterior › WINDOW / GLASS › WINDOW DEFOGGER SYSTEM
RM27L0U _59 Vehicle Exterior _049347 WINDOW / GLASS _0235941 WINDOW DEFOGGER SYSTEM U

WINDOW / GLASS  WINDOW DEFOGGER SYSTEM  TERMINALS OF ECU  


CHECK AIR CONDITIONING AMPLIFIER


U153933E02
3.865,0.344 4.167,0.521 0.302,0.177 10 false H24 1.667,0.344 1.969,0.521 0.302,0.177 10 false H67 5.521,0.333 5.781,0.51 0.26,0.177 10 false z13

a.

Disconnect the H24 air conditioning amplifier connector.


b.

Measure the resistance and voltage according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
H24-1 (IG+) - H24-14 (GND) P - W-B Ignition power supply Ignition switch ON 11 to 14 V
Ignition switch off Below 1 V
H24-21 (B) - H24-14 (GND) R - W-B Battery power source Always 11 to 14 V
H24-14 (GND) - Body ground W-B - Body ground Ground Always Below 1 Ω

If the result is not as specified, there may be a malfunction on the wire harness side.



c.

Reconnect the H24 air conditioning amplifier connector.


d.

Measure the voltage according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
H24-11 (CANH) - H24-14 (GND) B - W-B Hi-level CAN bus line Ignition switch ON Pulse generation
(see waveform 1)
H24-12 (CANL) - H24-14 (GND) W - W-B Lo-level CAN bus line Ignition switch ON Pulse generation
(see waveform 2)
H24-37 (LIN1) - H24-14 (GND) SB - W-B LIN communication signal Ignition switch ON Pulse generation
H24-38 (RDEF) - H24-14 (GND) R - W-B Defogger relay Ignition switch ON
Defogger switch OFF
11 to 14 V
Ignition switch ON
Back door window closed
Defogger switch ON
Below 1 V

If the result is not as specified, the air conditioning amplifier may have a malfunction.



e.
B443143E01
2.771,0.313 3.323,0.49 0.552,0.177 10 false 1 V/DIV. 2.979,1.396 3.302,1.563 0.323,0.167 10 false GND 1.615,1.896 2.448,2.083 0.833,0.188 10 false 10 μsec./DIV.

Waveform 1 (Reference) : Using an oscilloscope

CAN Communication Signal
Terminal Name CANH - GND
Tester Range 1 V/DIV., 10 μsec./DIV.
Condition Ignition switch ON

HINT:

The waveform varies depending on the CAN communication signal.



f.
B443144E01
2.771,0.25 3.323,0.417 0.552,0.167 10 false 1 V/DIV. 2.958,1.49 3.292,1.667 0.333,0.177 10 false GND 1.635,1.885 2.5,2.063 0.865,0.177 10 false 10 μsec./DIV.

Waveform 2 (Reference) : Using an oscilloscope

CAN Communication Signal
Terminal Name CANL - GND
Tester Range 1 V/DIV., 10 μsec./DIV.
Condition Ignition switch ON

HINT:

The waveform varies depending on the CAN communication signal.




CHECK INTEGRATION CONTROL AND PANEL


U153163E02
3.365,0.198 3.646,0.375 0.281,0.177 10 false H45

a.

Disconnect the H45 integration control and panel connector.


b.

Measure the resistance and voltage according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
H45-16 (IG+) - H45-1 (GND) P - W-B Ignition power supply Ignition switch off Below 1 V
Ignition switch ON 11 to 14 V
H45-1 (GND) - Body ground W-B - Body ground Ground Always Below 1 Ω

If the result is not as specified, there may be a malfunction on the wire harness side.



c.

Reconnect the H45 integration control and panel connector.


d.

Measure the voltage according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
H45-3 (STX) - H45-1 (GND) SB - W-B LIN communication circuit Ignition switch ON Pulse generation

If the result is not as specified, the integration control and panel may have a malfunction.