Home › Vehicle Exterior › WINDOW / GLASS › POWER WINDOW REGULATOR MOTOR
RM27L0U _59 Vehicle Exterior _049347 WINDOW / GLASS _0235945 POWER WINDOW REGULATOR MOTOR G

WINDOW / GLASS  POWER WINDOW REGULATOR MOTOR  INSPECTION  


PROCEDURE

Hide 85720C 1.INSPECT FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH

a.
B194348E01
1.648,3.008 2.307,3.159 0.659,0.151 10 Clockwise 1.849,2.628 2.965,2.785 1.116,0.157 10 Counterclockwise 0.071,0.055 2.541,0.544 2.471,0.489 10 Component without harness connected: (Front power window regulator motor assembly)

Check the operation of the regulator motor.

NOTICE:
·

Do not apply voltage to any terminals of the motor, except terminal 2, to avoid damaging the pulse sensor inside the motor.

·

Reset the power window regulator motor (initialize the pulse sensor) after installing the power window regulator motor and regulator assembly onto the door (See page Vehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM>INITIALIZATION).



i.

Apply battery voltage to the regulator motor and check the operation of the regulator motor.

OK:
Measurement Condition Motor Condition Specified Condition
Battery positive (+) → Terminal 2
Battery negative (-) → Terminal 1, 4 and 10
Auto Motor gear rotates clockwise
Battery positive (+) → Terminal 2
Battery negative (-) → Terminal 1, 4 and 7
Motor gear rotates counterclockwise
Battery positive (+) → Terminal 2
Battery negative (-) → Terminal 1 and 10
Manual Motor gear rotates clockwise
Battery positive (+) → Terminal 2
Battery negative (-) → Terminal 1 and 7
Motor gear rotates counterclockwise


If the result is not as specified, replace the power window regulator motor.



Hide 85710D 2.INSPECT FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY RH

a.
B194349E01
0.042,1.707 0.688,1.844 0.646,0.137 10 Clockwise 0.217,3.008 1.330,3.159 1.113,0.151 10 Counterclockwise 0.025,0.01 2.534,0.486 2.509,0.476 10 Component without harness connected: (Front power window regulator motor assembly)

Check the operation of the regulator motor.

NOTICE:
·

Do not apply voltage to any terminals of the motor, except terminal 2, to avoid damaging the pulse sensor inside the motor.

·

Reset the power window regulator motor (initialize the pulse sensor) after installing the power window regulator motor and regulator assembly onto the door (See page Vehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM>INITIALIZATION).



i.

Apply battery voltage to the regulator motor and check the operation of the regulator motor.

OK:
Measurement Condition Motor Condition Specified Condition
Battery positive (+) → Terminal 2
Battery negative (-) → Terminal 1, 4 and 7
Auto Motor gear rotates clockwise
Battery positive (+) → Terminal 2
Battery negative (-) → Terminal 1, 4 and 10
Motor gear rotates counterclockwise
Battery positive (+) → Terminal 2
Battery negative (-) → Terminal 1 and 7
Manual Motor gear rotates clockwise
Battery positive (+) → Terminal 2
Battery negative (-) → Terminal 1 and 10
Motor gear rotates counterclockwise


If the result is not as specified, replace the power window regulator motor.



Hide 85720D 3.INSPECT REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY LH

a.
B195594E02
0.073,0.104 2.74,0.646 2.667,0.542 10 false Component without harness connected: (Rear Power Window Regulator assembly LH) 0.042,1.885 0.771,2.208 0.729,0.323 10 true Clockwise 0.083,2.99 1.313,3.375 1.229,0.385 10 true Counterclockwise

Check the operation of the regulator motor.

i.

Apply battery voltage to the regulator motor and check the operation of the regulator motor.

OK:
Measurement Condition Specified Condition
Battery position (+) → Terminal 1
Battery negative (-) → Terminal 2
Motor gear rotates clockwise
Battery position (+) → Terminal 2
Battery negative (-) → Terminal 1
Motor gear rotates counterclockwise


If the result is not as specified, replace the power window regulator motor.



Hide 85710E 4.INSPECT REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY RH

a.
B195595E01
0.057,0.017 2.537,0.541 2.479,0.524 10 Component without harness connected: (Rear power window regulator motor assembly RH) 1.536,2.93 2.259,3.110 0.723,0.180 10 Clockwise 2.365,2.414 3.070,2.739 0.705,0.325 10 Counterclockwise

Check the operation of the regulator motor.

i.

Apply battery voltage to the regulator motor and check the operation of the regulator motor.

OK:
Measurement condition Specified Condition
Battery positive (+) → Terminal 2
Battery negative (-) → Terminal 1
Motor gear rotates clockwise
Battery positive (+) → Terminal 1
Battery negative (-) → Terminal 2
Motor gear rotates counterclockwise


If the result is not as specified, replace the power window regulator motor.