Home › Vehicle Exterior › WINDOW / GLASS › POWER WINDOW REGULATOR MOTOR
RM27L0U _59 Vehicle Exterior _049347 WINDOW / GLASS _0235945 POWER WINDOW REGULATOR MOTOR G

WINDOW / GLASS  POWER WINDOW REGULATOR MOTOR  ON-VEHICLE INSPECTION  


PROCEDURE

Hide 85720C 1.INSPECT FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH

a.
B194347E01
0.164,0.111 2.558,0.601 2.394,0.490 10 Component with harness connected: (Front power window regulator motor assembly LH)

Inspect PTC operation inside the power window regulator motor.

NOTICE:

The work must be performed with the power window regulator and door glass installed on the vehicle.


i.

Connect an electrical tester DC 400 A probe to the wire harness of terminal 1 or 2.

NOTICE:

Match the arrow mark on the probe with the direction of the current flow.



ii.

Fully close the door glass by pressing the power window UP switch. Wait for approximately 60 seconds.


iii.

Continue to press the power window UP switch and measure how long it takes for the electrical current to change from a range of 16 to 28 A to approximately 1 A (Inspection of current shut-off).

Standard:

4 to 90 seconds



iv.

Check that the door glass moves downward when the power window DOWN switch is pressed.

If the result is not as specified, replace the power window regulator motor.



Hide 85710D 2.INSPECT FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY RH

a.
B194347E02
0.164,0.111 2.558,0.601 2.394,0.490 10 Component with harness connected: (Front power window regulator motor assembly RH)

Inspect PTC operation inside the power window regulator motor.

NOTICE:

The work must be performed with the power window regulator and door glass installed on the vehicle.


i.

Connect an electrical tester DC 400 A probe to the wire harness of terminal 1 or 2.

NOTICE:

Match the arrow mark on the probe with the direction of the current flow.



ii.

Fully close the door glass by pressing the power window UP switch. Wait for approximately 60 seconds.


iii.

Continue to press the power window UP switch and measure how long it takes for the electrical current to change from a range of 16 to 28 A to approximately 1 A (Inspection of current shut-off).

Standard:

4 to 90 seconds



iv.

Check that the door glass moves downward when the power window DOWN switch is pressed.

If the result is not as specified, replace the power window regulator motor.



Hide 85720D 3.INSPECT REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY LH

a.
B164428E10
0.244,0 2.590,0.521 2.346,0.521 10 Component with harness connected: (Rear power window regulator motor assembly LH)

Inspect PTC operation inside the power window regulator motor.

NOTICE:

The work must be performed with the power window regulator and door glass installed on the vehicle.


i.

Connect an electrical tester DC 400 A probe to the wire harness of terminal 1.

NOTICE:

Match the arrow mark of the probe with the direction of the current flow.



ii.

Fully close the door glass by pressing the power window UP switch. Wait for approximately 60 seconds.


iii.

Continue to press the power window UP switch and measure how long it takes for the electrical current to change from a range of 16 to 28 A to approximately 1 A (Inspection of current shut-off).

Standard:

4 to 90 seconds



iv.

Check that the door glass moves downward when the power window DOWN switch is pressed.

If the result is not as specified, replace the power window regulator motor.



Hide 85710E 4.INSPECT REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY RH

a.
B164428E11
0.183,0.031 2.507,0.524 2.325,0.494 10 Component with harness connected: (Rear power window regulator motor assembly RH)

Inspect PTC operation inside the power window regulator motor.

NOTICE:

The work must be performed with the power window regulator and door glass installed on the vehicle.


i.

Connect an electrical tester DC 400 A probe to the wire harness of terminal 2.

NOTICE:

Match the arrow mark of the probe with the direction of the current flow.



ii.

Fully close the door glass by pressing the power window UP switch. Wait for approximately 60 seconds.


iii.

Continue to press the power window UP switch and measure how long it takes for the electrical current to change from a range of 16 to 28 A to approximately 1 A (Inspection of current shut-off).

Standard:

4 to 90 seconds



iv.

Check that the door glass moves downward when the power window DOWN switch is pressed.

If the result is not as specified, replace the power window regulator motor.