Home › Vehicle Exterior › DOOR / HATCH › FRONT DOOR
RM27L0U _59 Vehicle Exterior _049349 DOOR / HATCH _0235958 FRONT DOOR N

DOOR / HATCH  FRONT DOOR  ADJUSTMENT  


CAUTION / NOTICE / HINT

CAUTION:

Some of these service operations affect the SRS airbag system. Read the precautionary notices concerning the SRS airbag system before servicing (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>PRECAUTION).


B104980E01
0.227,1.662 1.124,1.863 0.897,0.201 10 Centering Bolt 2.096,1.662 2.954,1.863 0.859,0.201 10 Standard Bolt

HINT:
·

Use the same procedure for the RH and LH sides.

·

The procedure described below is for the RH side.

·

Centering bolts are used to mount the door hinge onto the vehicle body and door. The door cannot be adjusted with the centering bolts in. Substitute standard bolts (with washers) for the centering bolts when making adjustments.

·

For bolts without torque specifications, check the standard bolt chart (See page General>SPECIFICATIONS>STANDARD BOLT>SPECIFIED TORQUE FOR STANDARD BOLTS).



PROCEDURE

Hide 67002 1.INSPECT FRONT DOOR

a.

Check that the clearance measurements are within the standard ranges.

B190505E01
2.238,0.467 2.355,0.614 0.117,0.147 10 A 1.8,0.785 1.917,0.931 0.117,0.147 10 B 3.263,0.508 3.390,0.655 0.127,0.147 10 C 3.031,1.019 3.158,1.166 0.127,0.147 10 D 4.538,0.47 4.665,0.617 0.127,0.147 10 E 4.181,0.929 4.308,1.076 0.127,0.147 10 F 5.295,3.57 5.436,3.717 0.140,0.147 10 M 4.761,3.856 4.888,4.002 0.127,0.147 10 N 4.078,4.328 4.206,4.475 0.127,0.147 10 K 3.554,3.904 3.681,4.051 0.127,0.147 10 L 2.938,4.347 3.001,4.494 0.063,0.147 10 I 2.401,3.901 2.528,4.048 0.127,0.147 10 J 1.66,3.483 1.787,3.630 0.127,0.147 10 G 1.405,3.975 1.532,4.122 0.127,0.147 10 H

Standard:
Area Measurement Area Measurement
A 4.0 to 7.0 mm
(0.157 to 0.276 in.)
H -1.5 to 1.5 mm
(-0.059 to 0.059 in.)
B -1.5 to 1.5 mm
(-0.059 to 0.059 in.)
I 7.8 to 10.8 mm
(0.307 to 0.425 in.)
C 4.0 to 7.0 mm
(0.157 to 0.276 in.)
J 1.9 to 4.9 mm
(0.075 to 0.193 in.)
D 0.8 to 3.8 mm
(0.031 to 0.150 in.)
K 7.8 to 10.8 mm
(0.307 to 0.425 in.)
E 4.0 to 7.0 mm
(0.157 to 0.276 in.)
L 2.3 to 5.3 mm
(0.091 to 0.209 in.)
F 0.9 to 3.9 mm
(0.035 to 0.154 in.)
M 4.0 to 7.0 mm
(0.157 to 0.276 in.)
G 5.0 to 8.0 mm
(0.197 to 0.315 in.)
N -1.5 to 1.5 mm
(-0.059 to 0.059 in.)



Hide 67002 2.ADJUST FRONT DOOR

a.

Disconnect the cable from the negative battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.


NOTICE:

When disconnecting the cable some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).



b.
B192133

Using SST, adjust the door horizontally and vertically by loosening the body side hinge bolts.

SST
09812-00010  


c.

Tighten the body side hinge bolts after the adjustment.

Torque:
26 N*m (265 kgf*cm, 19 ft.*lbf)


d.
B192134

Using SST, adjust the door horizontally and vertically by loosening the door side hinge bolts.

SST
09812-00010  


e.

Tighten the door side hinge bolts after the adjustment.

Torque:
26 N*m (265 kgf*cm, 19 ft.*lbf)


f.
B192135

Using "TORX" socket wrench T40, adjust the striker position by slightly loosening the striker mounting screws and hitting the striker with a plastic-faced hammer.


g.

Using "TORX" socket wrench T40, tighten the striker mounting screws after the adjustment.

Torque:
23 N*m (235 kgf*cm, 17 ft.*lbf)


h.

Connect the cable to the negative battery terminal.

Torque:
5.4 N*m (55 kgf*cm, 48 in.*lbf)

CAUTION:

When disconnecting the cable some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).