Home › Vehicle Exterior › DOOR / HATCH › BACK DOOR
RM27L0U _59 Vehicle Exterior _049349 DOOR / HATCH _0235960 BACK DOOR N

DOOR / HATCH  BACK DOOR  ADJUSTMENT  


CAUTION / NOTICE / HINT

CAUTION:

Some of these service operations affect the SRS airbag system. Read the precautionary notices concerning the SRS airbag system before servicing (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>PRECAUTION).


B104980E01
0.227,1.662 1.124,1.863 0.897,0.201 10 Centering Bolt 2.096,1.662 2.954,1.863 0.859,0.201 10 Standard Bolt

HINT:
·

Centering bolts are used to mount the door hinge onto the vehicle body and door. The door cannot be adjusted with the centering bolts in. Substitute standard bolts (with washers) for the centering bolts when making adjustments.

·

For bolts without torque specifications, check the standard bolt chart (See page General>SPECIFICATIONS>STANDARD BOLT>SPECIFIED TORQUE FOR STANDARD BOLTS).



PROCEDURE

Hide 67005 1.INSPECT BACK DOOR

a.

Check that the clearance measurements are within the standard ranges.

B190507E01
3.33,0.331 3.447,0.476 0.117,0.145 10 A 3.832,0.591 3.942,0.738 0.110,0.147 10 B 5.749,0.541 5.881,0.685 0.133,0.145 10 C 5.608,0.908 5.734,1.057 0.126,0.150 10 D 5.644,2.071 5.759,2.218 0.115,0.147 10 E 5.419,2.49 5.527,2.635 0.109,0.145 10 F 5.07,4.046 5.194,4.187 0.124,0.141 10 H 5.586,4.2 5.720,4.346 0.134,0.146 10 G 3.785,4.007 3.866,4.158 0.082,0.151 10 I

Standard:
Area Measurement Area Measurement
A 11.9 mm
(0.469 in.)
F 0.2 mm
(0.008 in.)
B 1.6 mm
(0.063 in.)
G 6.0 mm
(0.236 in.)
C 8.0 mm
(0.315 in.)
H 0 mm
(0 in.)
D 2.1 mm
(0.083 in.)
I 15.1 mm
(0.594 in.)
E 6.6 mm
(0.260 in.)
- -



Hide 67005 2.ADJUST BACK DOOR

a.

Disconnect the cable from the negative battery terminal.

CAUTION:

Some of these service operations affect the SRS airbag system. Read the precautionary notices concerning the SRS airbag system before servicing (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).



b.
B192139

Adjust the door position.

i.

Horizontally and vertically adjust the door by loosening the door side hinge bolts.

Torque:
20 N*m (199 kgf*cm, 14 ft.*lbf)



c.
B192140

Adjust the striker position.

i.

Using "TORX" socket wrench T40, adjust the striker position by slightly loosening the striker mounting screws and hitting the striker with a plastic-faced hammer.


ii.

Using "TORX" socket wrench T40, tighten the striker mounting screws after the adjustment.

Torque:
27 N*m (275 kgf*cm, 20 ft.*lbf)



d.

Connect the cable to the negative battery terminal.

Torque:
5.4 N*m (55 kgf*cm, 48 in.*lbf)

CAUTION:

When disconnecting the cable some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).