Home › Vehicle Exterior › DOOR / HATCH › POWER BACK DOOR SYSTEM
RM27L0U _59 Vehicle Exterior _049349 DOOR / HATCH _0235968 POWER BACK DOOR SYSTEM J

DOOR / HATCH  POWER BACK DOOR SYSTEM  Power Back Door cannot be Opened or Closed Using the Power Back Door Switch  


DESCRIPTION

When the power back door cannot be opened or closed using the power back door control switch, one of the following may be malfunctioning: 1) back door control switch circuit, 2) power back door drive unit (power back door ECU), or 3) main body ECU.

HINT:

Since the power back door system has functions that use CAN communication, first confirm that there is no malfunction in the communication system by inspecting the CAN communication functions in accordance with the "How to Proceed with Troubleshooting" procedures. Then, conduct the following inspection procedure.


WIRING DIAGRAM

B443294E01
1.292,0.938 1.448,1.135 0.156,0.198 10 false 3 1.49,1.438 1.906,1.635 0.417,0.198 10 false H70 2.906,0.958 3.063,1.156 0.156,0.198 10 false 6 1.49,1.625 3.146,1.823 1.656,0.198 10 false Back Door Control Switch 0.729,2.396 2.75,2.594 2.021,0.198 10 false : CAN Communication Line 3.417,0.969 3.698,1.167 0.281,0.198 10 false 26 3.667,1.052 4.188,1.26 0.521,0.208 10 false PBDS 3.552,1.979 4.073,2.188 0.521,0.208 10 false H4 3.531,2.146 4.677,2.323 1.146,0.177 10 false Main Body ECU 5.344,1.938 5.865,2.146 0.521,0.208 10 false O30 5.354,2.125 7.104,2.469 1.75,0.344 10 false Power Back Door Drive Unit (Power Back Door ECU)

PROCEDURE

1.READ VALUE USING TECHSTREAM
a.

Connect the Techstream to the DLC3


b.

Turn the ignition switch to ON.


c.

Turn the Techstream on.


d.

Enter the following menus: Body Electrical / Main Body / Data List /


e.

According to the display on the Techstream, read the Data List.

Main Body
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Back Door Open SW Back door control switch / ON or OFF ON: Back door control switch is pushed
OFF: Back door control switch is not pushed
-

OK:

The back door control switch functions as specified in the normal condition.




OK

2.REPLACE POWER BACK DOOR DRIVE UNIT (POWER BACK DOOR ECU)

NG

4.INSPECT POWER BACK DOOR OPENER / CLOSER SWITCH
2.REPLACE POWER BACK DOOR DRIVE UNIT (POWER BACK DOOR ECU)
a.

Temporarily replace the power back door drive unit (power back door ECU) with a new or normally functioning one (See page Vehicle Exterior>DOOR / HATCH>POWER BACK DOOR DRIVE UNIT>REMOVAL).



NEXT

3.CHECK POWER BACK DOOR DRIVE UNIT (POWER BACK DOOR ECU)
3.CHECK POWER BACK DOOR DRIVE UNIT (POWER BACK DOOR ECU)
a.

Check that the power back door operates normally.

OK:

It operates normally.




OK

END (REPLACE POWER BACK DOOR DRIVE UNIT (POWER BACK DOOR ECU) DEFECTIVE)

NG

REPLACE MAIN BODY ECU (INSTRUMENT PANEL JUNCTION BLOCK LH)

4.INSPECT POWER BACK DOOR OPENER / CLOSER SWITCH
a.
B190838E04
0.604,3.792 0.729,3.792 0.729,3.792 0.979,3.354 false 1.615,2.969 1.49,2.969 1.49,2.969 1.188,3.354 false 1.688,2.896 2.188,3.042 0.5,0.146 10 false Pushed 0.135,3.76 0.656,4.115 0.521,0.354 10 false Not Pushed 0.25,0.021 2.74,0.365 2.49,0.344 10 false Component without harness connected: (Back Door Control Switch)

Remove the back door control switch (See page Vehicle Exterior>DOOR / HATCH>BACK DOOR OPENER SWITCH>REMOVAL).


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Position Specified Condition
3 - 6 Back door control switch not pushed (OFF) 10 kΩ or higher
3 - 6 Back door control switch pushed (ON) Below 1 Ω



c.

Reinstall the back door control switch.



OK

5.CHECK HARNESS AND CONNECTOR (CONTROL SWITCH - MAIN BODY ECU AND BODY GROUND)

NG

REPLACE POWER BACK DOOR OPENER / CLOSER SWITCH

5.CHECK HARNESS AND CONNECTOR (CONTROL SWITCH - MAIN BODY ECU AND BODY GROUND)
a.
U153233E02
0.979,3.469 1.104,3.469 1.104,3.469 2.208,4.229 true 0.281,0.083 2.604,0.458 2.323,0.375 10 false Front view of wire harness connector: (to Power Back Door Control Switch) 0.302,2.458 2.625,2.792 2.323,0.333 10 false Front view of wire harness connector: (to Main Body ECU) 0.458,3.396 0.865,3.552 0.406,0.156 10 false PBDS 0.719,1.625 1.031,1.781 0.313,0.156 10 false H70 0.615,3.906 0.823,4.042 0.208,0.135 10 false H4

Disconnect the H70 switch connector.


b.

Disconnect the H4 ECU connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H70-6 - H4-26 (PBDS) Always Below 1 Ω
H70-3 - Body ground Always Below 1 Ω
H70-6 - Body ground Always 10 kΩ or higher



d.

Reconnect the switch connector.


e.

Reconnect the ECU connector.



OK

6.REPLACE POWER BACK DOOR DRIVE UNIT (POWER BACK DOOR ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.REPLACE POWER BACK DOOR DRIVE UNIT (POWER BACK DOOR ECU)
a.

Replace the power back door drive unit (power back door ECU) (See page Vehicle Exterior>DOOR / HATCH>POWER BACK DOOR DRIVE UNIT>REMOVAL).



NEXT

7.CHECK POWER BACK DOOR DRIVE UNIT
7.CHECK POWER BACK DOOR DRIVE UNIT
a.

Check that the power back door operates normally.

OK:

It operates normally.




OK

END (REPLACE POWER BACK DOOR DRIVE UNIT (POWER BACK DOOR ECU) DEFECTIVE)

NG

REPLACE MAIN BODY ECU (INSTRUMENT PANEL JUNCTION BLOCK LH)