Home › Vehicle Exterior › DOOR / HATCH › POWER BACK DOOR SYSTEM
RM27L0U _59 Vehicle Exterior _049349 DOOR / HATCH _0235968 POWER BACK DOOR SYSTEM J

DOOR / HATCH  POWER BACK DOOR SYSTEM  Power Back Door cannot be Closed Using the Power Back Door Closer Switch  


DESCRIPTION

When the power back door cannot be closed using the power back door closer switch, one of the following may be malfunctioning: 1) power back door closer switch circuit, or 2) power back door drive unit (power back door ECU).

WIRING DIAGRAM

C179511E05
2.045,1.212 4.081,1.386 2.036,0.174 10 Power Back Door Closer Switch 3.755,0.689 3.897,0.831 0.142,0.142 10 8 2.148,0.68 2.276,0.835 0.128,0.156 10 5 5.495,0.688 5.626,0.855 0.130,0.167 10 4 5.725,0.773 6.027,0.950 0.302,0.177 10 DS1 5.179,2.16 6.947,2.506 1.768,0.346 10 Power Back Door drive Unit (Power back Door ECU) 1.976,1.073 2.262,1.212 0.286,0.139 10 O32 5.179,1.969 5.472,2.110 0.293,0.141 10 O30

PROCEDURE

1.READ VALUE USING TECHSTREAM
a.

Connect the Techstream to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the Techstream on.


d.

Enter the following menus: Body Electrical / Back Door / Data List /


e.

According to the display on the Techstream, read the Data List.

Back Door
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
PBD Close SW Power back door closer switch signal / ON or OFF ON: Power back door closer switch ON
OFF: Power back door closer switch OFF
-

OK:

The power back door closer switch functions as specified in the normal condition.




OK

REPLACE POWER BACK DOOR DRIVE UNIT (POWER BACK DOOR ECU)

NG

2.INSPECT POWER BACK DOOR CLOSER SWITCH
2.INSPECT POWER BACK DOOR CLOSER SWITCH
a.
B190837E01
1.724,2.495 2.214,2.651 0.490,0.156 10 Pushed 1.636,2.588 1.514,2.588 1.514,2.588 0.958,3.434 false 0.202,3.781 0.705,4.111 0.503,0.330 10 Not Pushed 0.524,3.87 0.646,3.87 0.646,3.87 0.961,3.488 false 0.222,0.043 2.711,0.383 2.489,0.340 10 Component without harness connected: (Power Back Door Closer Switch)

Remove the power back door closer switch (See page Vehicle Exterior>DOOR / HATCH>POWER BACK DOOR CONTROL SWITCH(for Luggage Compartment)>REMOVAL).


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Position Specified Condition
5 - 8 Pushed (ON) Below 1 Ω
5 - 8 Free (OFF) 10 kΩ or higher



c.

Reinstall the power back door closer switch.



OK

3.CHECK HARNESS AND CONNECTOR (CLOSER SWITCH - DOOR DRIVE UNIT AND BODY GROUND)

NG

3.CHECK HARNESS AND CONNECTOR (CLOSER SWITCH - DOOR DRIVE UNIT AND BODY GROUND)
a.
U153234E02
2.302,3.354 2.177,3.354 2.177,3.354 1.438,4.167 true 0.344,0.063 2.667,0.375 2.323,0.313 10 false Front view of wire harness connector: (to Power Back Door Closer Switch) 0.344,2.26 2.667,2.594 2.323,0.333 10 false Front view of wire harness connector: (to Power Back Door ECU) 2.365,3.281 2.656,3.438 0.292,0.156 10 false DS1 0.802,1.813 1.094,1.958 0.292,0.146 10 false O32 0.344,4.063 0.635,4.208 0.292,0.146 10 false O30

Disconnect the O32 switch connector.


b.

Disconnect the O30 ECU connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
O32-8 - O30-4 (DS1) Always Below 1 Ω
O32-5 - Body ground Always Below 1 Ω
O32-8 - Body ground Always 10 kΩ or higher



d.

Reconnect the switch connector.


e.

Reconnect the ECU connector.



OK

REPLACE POWER BACK DOOR DRIVE UNIT (POWER BACK DOOR ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR