Home › Vehicle Exterior › MIRROR (EXT) › OUTER REAR VIEW MIRROR
RM27L0U _59 Vehicle Exterior _049350 MIRROR (EXT) _0235971 OUTER REAR VIEW MIRROR G

MIRROR (EXT)  OUTER REAR VIEW MIRROR  INSPECTION  


PROCEDURE

Hide 87940 1.INSPECT OUTER REAR VIEW MIRROR ASSEMBLY LH

B166373E05
2.094,3.802 1.906,4.219 false 2.458,3.802 2.708,4.219 false 2.281,3.802 2.281,4.219 false 1.167,0.375 1.365,0.552 0.198,0.177 10 true (A) 1.031,1.448 1.229,1.625 0.198,0.177 10 true (B) 0.458,0.833 0.667,1.01 0.208,0.177 10 true (C) 1.635,0.927 1.844,1.104 0.208,0.177 10 true (D) 2.573,4.229 3.021,4.406 0.448,0.177 10 false MV 1.75,4.229 2.198,4.406 0.448,0.177 10 false MH 2.198,4.229 2.646,4.406 0.448,0.177 10 false M+ 0.083,2.042 2.625,2.5 2.542,0.458 10 false Component without harness connected: (Outer Rear View Mirror LH)

a.

Check the outer mirror motor operation.

i.

Apply battery voltage and check operation of the mirror face.

OK:
Measurement Condition Specified Condition
Battery positive (+) → Terminal 10 (MV)
Battery negative (-) → Terminal 11 (M+)
Turns upward (A)
Battery positive (+) → Terminal 11 (M+)
Battery negative (-) → Terminal 10 (MV)
Turns downward (B)
Battery positive (+) → Terminal 11 (M+)
Battery negative (-) → Terminal 12 (MH)
Turns left (C)
Battery positive (+) → Terminal 12 (MH)
Battery negative (-) → Terminal 11 (M+)
Turns right (D)


If the result is not as specified, replace the outer rear view mirror assembly LH.



b.

w/ Retract Mirror:

B443052E02
4.865,1.146 5.021,1.146 5.021,1.146 5.104,1.906 false 5.5,1.188 5.323,1.188 5.323,1.188 5.24,1.917 false 1.521,0.229 1.76,0.427 0.24,0.198 10 false (A) 0.99,1.094 1.198,1.292 0.208,0.198 10 false (B) 0.969,2.375 1.177,2.573 0.208,0.198 10 false (C) 1.938,3.073 2.146,3.271 0.208,0.198 10 false (D) 2.583,3.333 2.792,3.531 0.208,0.198 10 false (E) 4.615,1.083 4.833,1.271 0.219,0.188 10 false MF 5.563,1.094 5.781,1.281 0.219,0.188 10 false MR 1.75,0.229 2.833,0.427 1.083,0.198 10 false Forward Position 0.823,2.594 1.906,2.792 1.083,0.198 10 false Driving Position 2.802,3.344 3.99,3.542 1.188,0.198 10 false Retracted Position 4.313,0.094 6.719,0.448 2.406,0.354 10 false Component without harness connected: (Outer Rear View Mirror LH)

Check the retractable mirror's movement.

i.

For each position: Disconnect the battery, set the mirror position by hand, connect the battery, and check the retractable mirror's movement.

OK:
Measurement Condition Mirror Position Specified Condition
Battery positive (+) → Terminal 7 (MR)
Battery negative (-) → Terminal 8 (MF)
Forward position (A) Moves from (A) to retracted position (E)
Battery positive (+) → Terminal 8 (MF)
Battery negative (-) → Terminal 7 (MR)
Forward position (A) Does not move
Battery positive (+) → Terminal 7 (MR)
Battery negative (-) → Terminal 8 (MF)
Position between forward position (A) and driving position (C) Moves from (B) to retracted position (E)
Battery positive (+) → Terminal 8 (MF)
Battery negative (-) → Terminal 7 (MR)
Position between forward position (A) and driving position (C) Moves from (B) to forward position (A)
Battery positive (+) → Terminal 7 (MR)
Battery negative (-) → Terminal 8 (MF)
Driving position (C) Moves from (C) to retracted position (E)
Battery positive (+) → Terminal 8 (MF)
Battery negative (-) → Terminal 7 (MR)
Driving position (C) Does not move
Battery positive (+) → Terminal 7 (MR)
Battery negative (-) → Terminal 8 (MF)
Position between driving position (C) and retracted position (E) Moves from (D) to retracted position (E)
Battery positive (+) → Terminal 8 (MF)
Battery negative (-) → Terminal 7 (MR)
Position between driving position (C) and retracted position (E) Moves from (D) to driving position (C)
Battery positive (+) → Terminal 7 (MR)
Battery negative (-) → Terminal 8 (MF)
Retracted position (E) Does not move
Battery positive (+) → Terminal 8 (MF)
Battery negative (-) → Terminal 7 (MR)
Retracted position (E) Moves from (E) to driving position (C)


NOTICE:
·

Disconnect and reconnect the battery between each mirror position check.


·

Do not apply battery voltage when moving the mirror by hand into each mirror position.



If the result is not as specified, replace the outer rear view mirror assembly LH.



c.
B166835E05
1.719,3.813 1.427,4.281 true 1.875,3.813 2.177,4.302 true 2.208,4.333 2.521,4.51 0.313,0.177 10 false EC- 1.292,4.323 1.594,4.479 0.302,0.156 10 false EC+ 0.344,2.177 2.865,2.563 2.521,0.385 10 false Component without harness connected: (Outer Rear View Mirror LH) 0.51,0.354 0.938,0.563 0.427,0.208 10 false Bright 0.563,1.479 0.938,1.688 0.375,0.208 10 false Dark

w/ EC Mirror:

Check the EC mirror operation.

i.

Connect a dry battery of 1.5 V in series.


ii.

Apply dry battery voltage and check operation of the mirror face, as shown in the table and illustration.

OK:
Measurement Connection Specified Condition
Positive (+) end of the battery → Terminal 14 (EC+)
Negative (-) end of the battery → Terminal 13 (EC-)
Mirror surface becomes dark


NOTICE:

Do not apply a voltage of 1.5 V or higher.


If the result is not as specified, replace the outer rear view mirror assembly LH.



d.
B166375E03
2.742,2.922 2.885,3.103 0.143,0.181 10 + 2.593,2.608 2.680,2.790 0.087,0.181 10 - 2.713,3.009 2.639,3.009 2.639,3.009 2.451,3.407 false 2.549,2.714 2.474,2.714 2.474,2.714 2.287,3.403 false 0.152,1.898 2.634,2.239 2.482,0.341 10 Component without harness connected: (Outer Rear View Mirror LH)

w/ Mirror Heater:

Check the mirror heater.

i.

Apply battery voltage and check the operation of the mirror heater.

OK:
Measurement Condition Specified Condition
Battery positive (+) → Terminal 1 (+)
Battery negative (-) → Terminal 2 (-)
Mirror becomes warm


HINT:

It will take a short time for the mirror to become warm.


If the result is not as specified, replace the outer rear view mirror assembly LH.



Hide 87910 2.INSPECT OUTER REAR VIEW MIRROR ASSEMBLY RH

B166376E06
2.073,3.823 1.875,4.24 false 2.448,3.813 2.625,4.24 false 2.271,3.813 2.271,4.24 false 1.906,0.354 2.104,0.531 0.198,0.177 10 true (A) 2.083,1.469 2.281,1.646 0.198,0.177 10 true (B) 1.417,0.948 1.625,1.125 0.208,0.177 10 true (C) 2.594,0.813 2.802,0.99 0.208,0.177 10 true (D) 2.49,4.24 2.938,4.417 0.448,0.177 10 false MV 1.729,4.24 2.177,4.417 0.448,0.177 10 false MH 2.135,4.24 2.583,4.417 0.448,0.177 10 false M+ 0.083,2.073 2.625,2.531 2.542,0.458 10 false Component without harness connected: (Outer Rear View Mirror RH)

a.

Check the outer mirror motor operation.

i.

Apply battery voltage and check operation of the mirror face.

OK:
Measurement Condition Specified Condition
Battery positive (+) → Terminal 10 (MV)
Battery negative (-) → Terminal 11 (M+)
Turns upward (A)
Battery positive (+) → Terminal 11 (M+)
Battery negative (-) → Terminal 10 (MV)
Turns downward (B)
Battery positive (+) → Terminal 11 (M+)
Battery negative (-) → Terminal 12 (MH)
Turns left (C)
Battery positive (+) → Terminal 12 (MH)
Battery negative (-) → Terminal 11 (M+)
Turns right (D)


If the result is not as specified, replace the outer rear view mirror assembly RH.



b.

w/ Retract Mirror:

B443053E02
5.104,1.969 5.01,1.396 5.01,1.396 4.865,1.396 false 5.271,1.969 5.333,1.406 5.333,1.406 5.49,1.406 false 2.458,0.188 2.698,0.396 0.24,0.208 10 false (A) 2.979,1.115 3.219,1.323 0.24,0.208 10 false (B) 2.99,2.167 3.229,2.375 0.24,0.208 10 false (C) 2.208,2.854 2.448,3.063 0.24,0.208 10 false (D) 1.344,3.188 1.583,3.396 0.24,0.208 10 false (E) 4.396,0.302 6.792,0.667 2.396,0.365 10 false Component without harness connected: (Outer Rear View Mirror RH) 4.625,1.333 4.844,1.51 0.219,0.177 10 false MF 5.521,1.333 5.74,1.51 0.219,0.177 10 false MR 2.698,0.198 3.76,0.375 1.063,0.177 10 false Forward Position 2.313,2.458 3.365,2.813 1.052,0.354 10 true Driving Position 1.563,3.188 2.729,3.375 1.167,0.188 10 false Retracted Position

Check the retractable mirror's movement.

i.

For each position: Disconnect the battery, set the mirror position by hand, connect the battery, and check the retractable mirror's movement.

OK:
Measurement Condition Mirror Position Specified Condition
Battery positive (+) → Terminal 7 (MR)
Battery negative (-) → Terminal 8 (MF)
Forward position (A) Moves from (A) to retracted position (E)
Battery positive (+) → Terminal 8 (MF)
Battery negative (-) → Terminal 7 (MR)
Forward position (A) Does not move
Battery positive (+) → Terminal 7 (MR)
Battery negative (-) → Terminal 8 (MF)
Position between forward position (A) and driving position (C) Moves from (B) to retracted position (E)
Battery positive (+) → Terminal 8 (MF)
Battery negative (-) → Terminal 7 (MR)
Position between forward position (A) and driving position (C) Moves from (B) to forward position (A)
Battery positive (+) → Terminal 7 (MR)
Battery negative (-) → Terminal 8 (MF)
Driving position (C) Moves from (C) to retracted position (E)
Battery positive (+) → Terminal 8 (MF)
Battery negative (-) → Terminal 7 (MR)
Driving position (C) Does not move
Battery positive (+) → Terminal 7 (MR)
Battery negative (-) → Terminal 8 (MF)
Position between driving position (C) and retracted position (E) Moves from (D) to retracted position (E)
Battery positive (+) → Terminal 8 (MF)
Battery negative (-) → Terminal 7 (MR)
Position between driving position (C) and retracted position (E) Moves from (D) to driving position (C)
Battery positive (+) → Terminal 7 (MR)
Battery negative (-) → Terminal 8 (MF)
Retracted position (E) Does not move
Battery positive (+) → Terminal 8 (MF)
Battery negative (-) → Terminal 7 (MR)
Retracted position (E) Moves from (E) to driving position (C)


NOTICE:
·

Disconnect and reconnect the battery between each mirror position check.


·

Do not apply battery voltage when moving the mirror by hand into each mirror position.



If the result is not as specified, replace the outer rear view mirror assembly RH.



c.
B166836E05
1.708,3.813 1.396,4.344 false 1.875,3.823 2.25,4.323 false 2.198,4.375 2.646,4.552 0.448,0.177 10 false EC- 1.208,4.354 1.656,4.531 0.448,0.177 10 false EC+ 0.208,2.219 2.615,2.635 2.406,0.417 10 false Component without harness connected: (Outer Rear View Mirror RH) 2.635,0.292 3.156,0.5 0.521,0.208 10 false Bright 2.635,1.563 3.156,1.771 0.521,0.208 10 false Dark

w/ EC Mirror:

Check the EC mirror operation.

i.

Connect a dry battery of 1.5 V in series.


ii.

Apply dry battery voltage and check operation of the mirror face, as shown in the table and illustration.

OK:
Measurement Connection Specified Condition
Positive (+) end of the battery → Terminal 14 (EC+)
Negative (-) end of the battery → Terminal 13 (EC-)
Mirror surface becomes dark


NOTICE:

Do not apply a voltage of 1.5 V or higher.


If the result is not as specified, replace the outer rear view mirror assembly RH.



d.
B166378E05
2.715,2.922 2.831,3.104 0.115,0.181 10 + 2.561,2.613 2.652,2.795 0.092,0.181 10 - 2.696,3.005 2.622,3.005 2.622,3.005 2.434,3.402 false 2.532,2.709 2.457,2.709 2.457,2.709 2.27,3.398 false 0.135,1.953 2.617,2.594 2.482,0.640 10 Component without harness connected: (Outer Rear View Mirror RH)

w/ Mirror Heater:

Check the mirror heater.

i.

Apply battery voltage and check the operation of the mirror heater.

OK:
Measurement Condition Specified Condition
Battery positive (+) → Terminal 1 (+)
Battery negative (-) → Terminal 2 (-)
Mirror becomes warm


HINT:

It will take a short time for the mirror to become warm.


If the result is not as specified, replace the outer rear view mirror assembly RH.