Home › Vehicle Exterior › MIRROR (EXT) › OUTER MIRROR SWITCH
RM27L0U _59 Vehicle Exterior _049350 MIRROR (EXT) _0235973 OUTER MIRROR SWITCH G

MIRROR (EXT)  OUTER MIRROR SWITCH  INSPECTION  


PROCEDURE

Hide 84870A 1.INSPECT OUTER MIRROR SWITCH ASSEMBLY (w/o Retract Mirror)

B167984E02
2.202,3.86 3.113,4.215 false 2.059,3.848 2.562,4.222 false 1.929,3.854 2.124,4.231 false 1.752,3.857 1.75,4.225 false 1.603,3.86 1.373,4.198 false 1.438,3.851 1.078,4.202 false 1.302,3.851 0.78,4.201 false 0.655,4.238 0.767,4.415 0.112,0.177 10 B 0.97,4.238 1.112,4.417 0.142,0.179 10 E 1.236,4.238 1.473,4.410 0.237,0.172 10 M+ 1.582,4.238 1.902,4.382 0.320,0.144 10 MLH 2.025,4.238 2.382,4.403 0.357,0.165 10 MLV 2.467,4.238 2.796,4.405 0.329,0.167 10 MRV 2.934,4.238 3.311,4.429 0.377,0.191 10 MRH 0.203,2.042 2.767,2.724 2.563,0.682 10 Component without harness connected: (Outer Mirror Switch)

a.

Check the resistance.

i.

Select "L" on the left/right adjustment switch.


ii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
4 (MLV) - 8 (B)
6 (M+) - 7 (E)
UP Pressed Below 1 Ω
Not pressed 10 kΩ or higher
4 (MLV) - 7 (E)
6 (M+) - 8 (B)
DOWN Pressed Below 1 Ω
Not pressed 10 kΩ or higher
5 (MLH) - 8 (B)
6 (M+) - 7 (E)
LEFT Pressed Below 1 Ω
Not pressed 10 kΩ or higher
5 (MLH) - 7 (E)
6 (M+) - 8 (B)
RIGHT Pressed Below 1 Ω
Not pressed 10 kΩ or higher


If the result is not as specified, replace the outer mirror switch.


iii.

Select "R" on the left/right adjustment switch.


iv.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3 (MRV) - 8 (B)
6 (M+) - 7 (E)
UP Pressed Below 1 Ω
Not pressed 10 kΩ or higher
3 (MRV) - 7 (E)
6 (M+) - 8 (B)
DOWN Pressed Below 1 Ω
Not pressed 10 kΩ or higher
2 (MRH) - 8 (B)
6 (M+) - 7 (E)
LEFT Pressed Below 1 Ω
Not pressed 10 kΩ or higher
2 (MRH) - 7 (E)
6 (M+) - 8 (B)
RIGHT Pressed Below 1 Ω
Not pressed 10 kΩ or higher


If the result is not as specified, replace the outer mirror switch.



Hide 84870A 2.INSPECT OUTER MIRROR SWITCH ASSEMBLY (w/ Retract Mirror)

B167985E03
1.073,3.76 0.813,3.125 false 0.927,3.76 0.385,3.344 false 2.177,3.844 3.052,4.177 false 2,3.844 2.5,4.177 false 1.865,3.865 2.063,4.188 false 1.688,3.875 1.688,4.188 false 1.521,3.854 1.302,4.156 false 1.365,3.854 1.01,4.156 false 1.208,3.844 0.719,4.156 false 0.156,2.01 2.719,2.365 2.563,0.354 10 false Component without harness connected: (Outer Mirror Switch) 0.635,2.927 0.917,3.104 0.281,0.177 10 false MR 0.156,3.271 0.375,3.448 0.219,0.177 10 false MF 0.604,4.188 0.719,4.365 0.115,0.177 10 false B 0.906,4.198 1.052,4.375 0.146,0.177 10 false E 1.167,4.198 1.406,4.375 0.24,0.177 10 false M+ 1.521,4.198 1.844,4.344 0.323,0.146 10 false MLH 1.958,4.198 2.313,4.365 0.354,0.167 10 false MLV 2.396,4.198 2.729,4.365 0.333,0.167 10 false MRV 2.865,4.198 3.24,4.385 0.375,0.188 10 false MRH

a.

Inspect the outer mirror switch.

i.

Select "L" on the left/right adjustment switch.


ii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
4 (MLV) - 8 (B)
6 (M+) - 7 (E)
UP Pressed Below 1 Ω
Not pressed 10 kΩ or higher
4 (MLV) - 7 (E)
6 (M+) - 8 (B)
DOWN Pressed Below 1 Ω
Not pressed 10 kΩ or higher
5 (MLH) - 8 (B)
6 (M+) - 7 (E)
LEFT Pressed Below 1 Ω
Not pressed 10 kΩ or higher
5 (MLH) - 7 (E)
6 (M+) - 8 (B)
RIGHT Pressed Below 1 Ω
Not pressed 10 kΩ or higher


If the result is not as specified, replace the outer mirror switch.


iii.

Select "R" on the left/right adjustment switch.


iv.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3 (MRV) - 8 (B)
6 (M+) - 7 (E)
UP Pressed Below 1 Ω
Not pressed 10 kΩ or higher
3 (MRV) - 7 (E)
6 (M+) - 8 (B)
DOWN Pressed Below 1 Ω
Not pressed 10 kΩ or higher
2 (MRH) - 8 (B)
6 (M+) - 7 (E)
LEFT Pressed Below 1 Ω
Not pressed 10 kΩ or higher
2 (MRH) - 7 (E)
6 (M+) - 8 (B)
RIGHT Pressed Below 1 Ω
Not pressed 10 kΩ or higher


If the result is not as specified, replace the outer mirror switch.



b.

Inspect the retract switch.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
8 (B) - 9 (MR)
10 (MF) - 7 (E)
Pressed
(Retracts)
Below 1 Ω
Not pressed 10 kΩ or higher
8 (B) - 10 (MF)
7 (E) - 9 (MR)
Pressed
(Driving position)
Below 1 Ω
Not pressed 10 kΩ or higher


If the result is not as specified, replace the outer mirror switch.



Hide 84870A 3.INSPECT OUTER MIRROR SWITCH ASSEMBLY (w/ Memory)

B167772E15
2.156,3.854 2.146,4.208 false 2,3.854 1.844,4.208 false 1.813,3.854 1.521,4.219 false 1.219,3.854 1.073,4.219 false 2.344,3.833 2.552,4.208 false 0.104,2.281 2.573,2.625 2.469,0.344 10 false Component without harness connected: (Outer Mirror Switch) 2.094,4.219 2.25,4.396 0.156,0.177 10 false E 1.719,4.219 2.042,4.396 0.323,0.177 10 false M+ 2.365,4.219 2.74,4.396 0.375,0.177 10 false MSW 1.375,4.219 1.573,4.396 0.198,0.177 10 false E2 0.938,4.219 1.24,4.396 0.302,0.177 10 false MF

a.

Inspect the outer mirror switch.

i.

Select "L" on the left/right adjustment switch.


ii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3 (M+) - 2 (E) UP Pressed 100 Ω
Not pressed 10 kΩ or higher
3 (M+) - 2 (E) DOWN Pressed 470 Ω
Not pressed 10 kΩ or higher
3 (M+) - 2 (E) LEFT Pressed 800 Ω
Not pressed 10 kΩ or higher
3 (M+) - 2 (E) RIGHT Pressed 250 Ω
Not pressed 10 kΩ or higher
1 (MSW) - 2 (E) L switch Pressed 100 Ω
Not pressed 10 kΩ or higher


If the result is not as specified, replace the outer mirror switch.


iii.

Select "R" on the left/right adjustment switch.


iv.

Using an ohmmeter, measure the resistance and check the results in accordance with the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3 (M+) - 2 (E) UP Pressed 100 Ω
Not pressed 10 kΩ or higher
3 (M+) - 2 (E) DOWN Pressed 470 Ω
Not pressed 10 kΩ or higher
3 (M+) - 2 (E) LEFT Pressed 800 Ω
Not pressed 10 kΩ or higher
3 (M+) - 2 (E) RIGHT Pressed 250 Ω
Not pressed 10 kΩ or higher
1 (MSW) - 2 (E) R switch Pressed Below 1 Ω
Not pressed 10 kΩ or higher


If the result is not as specified, replace the outer mirror switch.



b.

Inspect the retract switch.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
8 (MF) - 4 (E2) Pressed Below 1 Ω
Not pressed 10 kΩ or higher


If the result is not as specified, replace the outer mirror switch.