Home › Vehicle Exterior › WIPER / WASHER › WIPER AND WASHER SYSTEM
RM27L0U _59 Vehicle Exterior _049351 WIPER / WASHER _0235977 WIPER AND WASHER SYSTEM U

WIPER / WASHER  WIPER AND WASHER SYSTEM  TERMINALS OF ECU  


CHECK MAIN BODY ECU (COWL SIDE JUNCTION BLOCK LH)


U153563E04
2.896,1.104 2.813,1.104 2.813,1.104 2.396,1.365 false 5.5,0.729 5.406,0.729 5.406,0.729 5,0.979 false 2.885,1.646 2.813,1.646 2.813,1.646 2.406,1.802 false 2.896,2.615 2.813,2.615 2.813,2.615 2.396,2.365 false 2.865,2.26 2.792,2.26 2.792,2.26 2.385,2.156 false 2.24,2.813 2.469,2.979 0.229,0.167 10 false DA 1.969,2.052 2.177,2.219 0.208,0.167 10 false DB 1.969,1.177 2.219,1.344 0.25,0.167 10 false DC 4.948,1.667 5.167,1.833 0.219,0.167 10 false DD 5.531,0.656 5.74,0.823 0.208,0.167 10 false DE 2.927,2.531 3.146,2.698 0.219,0.167 10 false H1 2.896,2.167 3.115,2.333 0.219,0.167 10 false H2 2.938,1.552 3.156,1.719 0.219,0.167 10 false H3 2.948,1.021 3.167,1.188 0.219,0.167 10 false H4 3.094,3.625 3.292,3.781 0.198,0.156 10 false DB 1.573,5.115 1.792,5.26 0.219,0.146 10 false DD 4.396,5.115 4.604,5.26 0.208,0.146 10 false DE 1.063,3.625 1.271,3.771 0.208,0.146 10 false DA 5.656,3.615 5.885,3.76 0.229,0.146 10 false DC 6.021,6.958 6.219,7.115 0.198,0.156 10 false H4 3.552,6.969 3.75,7.115 0.198,0.146 10 false H3 1.073,6.969 1.281,7.115 0.208,0.146 10 false H2 6.115,5.135 6.313,5.271 0.198,0.135 10 false H1

a.

Disconnect the DA, DB and DD main body ECU connectors.


b.

Measure the resistance and voltage according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
DA-1 (ALTB) - Body ground B - Body ground Battery power supply Always 11 to 14 V
DB-13 (BECU) - Body ground GR - Body ground Battery power supply Always 11 to 14 V
DD-62 (GND1, 2) - Body ground W-B - Body ground Ground Always Below 1 Ω

If the result is not as specified, there may be a malfunction on the wire harness side.


c.

Reconnect the main body ECU connectors.


d.

Measure the voltage according to the value(s) in the table below.



Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
DA-1 (IG) - DD-62 (GND1, 2) B - W-B IG power supply Ignition switch off Below 1 V
Ignition switch ON 11 to 14 V
H2-10 (LIN2) - DD-62 (GND1, 2) V - W-B LIN communication signal Ignition switch ON Signal waveform
H2-14 (RWMR) - DD-62 (GND1, 2) BE - W-B Rear washer motor operation signal Ignition switch ON and rear washer motor OFF 11 to 14 V
Ignition switch ON and rear washer motor ON Below 1 V
H3-2 (RWIN) - DD-62 (GND1, 2) L - W-B Rear wiper switch signal Ignition switch ON and rear wiper switch OFF 11 to 14 V
Ignition switch ON and wiper switch LO Below 1 V
H3-9 (RWON) - DD-62 (GND1, 2) W - W-B Rear wiper switch signal Ignition switch ON and rear wiper switch OFF 11 to 14 V
Ignition switch ON and rear wiper switch HI Below 1 V
H4-7 (RWSW) - DD-62 (GND1, 2) Y - W-B Rear washer switch signal Ignition switch ON and rear washer switch OFF 11 to 14 V
Ignition switch ON and rear washer switch ON Below 1 V
DD-23 (HRLY) - DD-62 (GND1, 2) SB - W-B Headlight LO signal Headlight LO switch OFF 11 to 14 V
Headlight LO switch ON Below 1 V
DB-12 (IG) - DD-62 (GND1, 2) Y - W-B Headlight cleaner control relay IG signal Ignition switch off Below 1 V
Ignition switch ON 11 to 14 V

If the result is not as specified, there may be a malfunction on the wire harness side.

CHECK BACK DOOR ECU


U154116E02
2.292,0.26 2.479,0.438 0.188,0.177 10 false V2 3.76,0.26 3.948,0.438 0.188,0.177 10 false V3

If the result is not as specified, there may be a malfunction on the wire harness side.

a.

Disconnect the V2 and V3 back door ECU connectors.


b.

Measure the resistance and voltage according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
V2-1 (BDR) - Body ground SB - Body ground Battery power supply Always 11 to 14 V
V2-6 (GND) - Body ground W-B - Body ground Ground Always Below 1 Ω
V2-7 (BECU) - Body ground GR - Body ground Battery power supply Always 11 to 14 V
V2-8 (SIG) - Body ground Y - Body ground IG power supply Ignition switch off Below 1 V
Ignition switch ON 11 to 14 V
V3-7 (BKUL) - V3-19 (KEYE) LG - BE Tail gate control switch signal Back door key cylinder turned UNLOCK Below 1 Ω
V3-8 (BKL) - V3-19 (KEYE) G - BE Tail gate control switch signal Back door key cylinder turned LOCK Below 1 Ω

If the result is not as specified, there may be a malfunction on the wire harness side.


c.

Reconnect the back door ECU connectors.


d.

Measure the resistance and voltage according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
V2-16 (MPX1) - V2-6 (GND) Y - W-B LIN communication signal Ignition switch ON Signal waveform
V2-21 (A UP) - V2-6 (GND) G - W-B Back door power window AUTO UP signal Ignition switch ON and back door power window switch OFF → AUTO UP Pulse generation → Below 1 V
V2-22 (BUP) - V2-6 (GND) BE - W-B Back door power window UP signal Ignition switch ON and back door power window switch OFF → UP Pulse generation → Below 1 V
V2-23 (BDN) - V2-6 (GND) V - W-B Back door power window DOWN signal Ignition switch ON and back door power window switch OFF → DOWN Pulse generation → Below 1 V
V2-24 (A DN) - V2-6 (GND) L - W-B Back door power window AUTO DOWN signal Ignition switch ON and back door power window switch OFF → AUTO DOWN Pulse generation → Below 1 V
V3-5 (BDUP) - V2-6 (GND) BE - W-B Back door power window UP operation signal Ignition switch ON and back door power window switch OFF → UP Below 1 V → 11 to 14 V
V3-6 (BDDN) - V2-6 (GND) P - W-B Back door power window DOWN operation signal Ignition switch ON and back door power window switch OFF → DOWN Below 1 V → 11 to 14 V
V3-1 (WIP-) - V2-6 (GND) P - W-B Rear wiper motor operation signal Ignition switch ON and rear wiper switch LO or HI Pulse generation
V3-2 (WIP+) - V2-6 (GND) L - W-B Rear wiper motor operation signal Ignition switch ON and rear wiper switch LO or HI Pulse generation
V3-16 (W) - V2-6 (GND) R - W-B Rear wiper reverse position switch signal Ignition switch ON and rear wiper switch LO or HI Pulse generation
V3-17 (P) - V3-25 (SGND) V - G Rear wiper retractable position switch signal Ignition switch ON and rear wiper switch OFF → ON Below 1 V → Pulse generation
V3-12 (DSV) - V3-23 (DSG) LG - SB Power supply for Hall-IC Ignition switch ON 11 to 14 V
V3-13 (DS1) - V3-23 (DSG) L - SB Back door power window glass position signal Back door power window operation Pulse generation
V3-14 (DS2) - V3-23 (DSG) Y - SB Back door power window glass position signal Back door power window operation Pulse generation
V3-19 (KEYE) - V2-6 (GND) BE - W-B Ground for Tail gate control switch Always Below 1 Ω
V3-23 (DSG) - V2-6 (GND) SB - W-B Ground for Hall-IC Always Below 1 Ω
V3-25 (SGND) - V2-6 (GND) G - W-B Ground for rear wiper reverse position and rear wiper retractable position switch Always Below 1 Ω

If the result is not as specified, there may be a malfunction on the wire harness side.



CHECK HEADLIGHT CLEANER CONTROL RELAY


U154022E02
3.417,0.229 3.677,0.406 0.26,0.177 10 false A32

a.

Disconnect the relay connector.


b.

Measure the resistance and voltage according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
A32-3 (IG) - A32-4 (E) GR - W-B IG power supply Ignition switch off Below 1 V
Ignition switch ON 11 to 14 V
A32-4(E) - Body ground W-B - Body ground Ground Always Below 1 Ω
A32-2 (H) - A32-4 (E) BR - W-B Headlight cleaner switch and headlight switch operation signal Headlight cleaner switch OFF Below 1 V
Headlight switch OFF Below 1 V
Headlight cleaner switch ON and headlight switch ON 11 to 14 V

If the result is not as specified, there may be a malfunction on the wire harness side.


c.

Reconnect the relay connector.


d.

Measure the voltage according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
A32-6 (PB) - A32-4 (E) R - W-B Headlight cleaner motor operation signal Headlight cleaner motor stopped 11 to 14 V
Headlight cleaner motor operating Below 1 V

If the result is not as specified, the relay may have a malfunction.