Home › Vehicle Exterior › WIPER / WASHER › FRONT WIPER MOTOR
RM27L0U _59 Vehicle Exterior _049351 WIPER / WASHER _0235978 FRONT WIPER MOTOR A

WIPER / WASHER  FRONT WIPER MOTOR  INSTALLATION  


PROCEDURE

Hide 85110 1.INSTALL WINDSHIELD WIPER MOTOR ASSEMBLY

a.
E161320

Install the windshield wiper motor with the 3 bolts.

Torque:
7.0 N*m (71 kgf*cm, 62 in.*lbf)


b.
E161319

Align the matchmarks on the crank arm and front wiper motor.


c.

Install the crank arm with the nut.

Torque:
7.0 N*m (71 kgf*cm, 62 in.*lbf)


d.
E161318

Apply MP grease to the crank arm pivot of the wiper motor.


e.

Install the rod of the wiper link to the crank arm, as shown in the illustration.


Hide 2.INSTALL FRONT WIPER MOTOR AND LINK ASSEMBLY

a.
E161316

Install the wiper motor and link assembly with the 4 bolts and nut.

Torque:
7.0 N*m (71 kgf*cm, 62 in.*lbf)


b.

Connect the connector.


Hide 55781E 3.INSTALL COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY

a.
E161314

Engage the 6 claws and 8 guides and install the cowl top ventilator louver sub-assembly.


b.

Install the 2 clips.


Hide 53866J 4.INSTALL FRONT FENDER TO COWL SIDE SEAL RH

a.
E161313

Engage the claw and install the front fender to cowl side seal.


Hide 53867H 5.INSTALL FRONT FENDER TO COWL SIDE SEAL LH

HINT:

Use the same procedure for both sides.


Hide 85211B 6.INSTALL FRONT WIPER ARM AND BLADE ASSEMBLY RH

a.
E146308E02
2.252,0.113 2.925,0.450 0.673,0.337 10 Wiper Arm Serration 2.442,1.912 3.181,2.076 0.738,0.164 10 Wire Brush 0.151,4.196 1.501,4.361 1.350,0.165 10 Wiper Pivot Serration 1.562,3.069 0.99,4.127 false 2.213,0.192 1.827,0.804 false 2.379,1.996 2.157,2.422 false

Clean any metal powder off the serrated part of the wiper arm with a round wire brush or the equivalent (when reinstalling).


b.

Clean the wiper pivot serrations with a wire brush.


c.

Operate the wiper, and then stop the wiper motor in the automatic stop position.


d.
E161321E02
1.635,2.354 0.26,1.771 false 1.708,2.229 2.677,2.583 0.969,0.354 10 false Mark for Blade Position

Align the blade tip with the mark on the glass, as shown in the illustration.

HINT:

Hold down the wiper arm hinge with your hand while tightening the nut.



e.

Tighten the nut on the front wiper arm and blade.

Torque:
24 N*m (245 kgf*cm, 18 ft.*lbf)

Operate the front wipers while spraying washer fluid on the windshield glass. Make sure that the front wipers function properly and there is no interference with the vehicle body.


Hide 85221B 7.INSTALL FRONT WIPER ARM AND BLADE ASSEMBLY LH

a.
E146308E02
2.252,0.113 2.925,0.450 0.673,0.337 10 Wiper Arm Serration 2.442,1.912 3.181,2.076 0.738,0.164 10 Wire Brush 0.151,4.196 1.501,4.361 1.350,0.165 10 Wiper Pivot Serration 1.562,3.069 0.99,4.127 false 2.213,0.192 1.827,0.804 false 2.379,1.996 2.157,2.422 false

Clean any metal powder off the serrated part of the wiper arm with a round wire brush or the equivalent (when reinstalling).


b.

Clean the wiper pivot serrations with a wire brush.


c.

Operate the wiper, and then stop the wiper motor in the automatic stop position.


d.
E161322E01
1.565,2.239 3.077,2.418 1.511,0.179 10 Mark for Blade Position 1.545,2.325 1.395,1.907 false

Align the blade tip with the mark on the glass, as shown in the illustration.

HINT:

Hold down the wiper arm hinge with your hand while tightening the nut.



e.

Tighten the nut on the front wiper arm and blade.

Torque:
24 N*m (245 kgf*cm, 18 ft.*lbf)


f.

Operate the front wipers while spraying washer fluid on the windshield glass. Make sure that the front wipers function properly and there is no interference with the vehicle body.