Home › Vehicle Exterior › WIPER / WASHER › FRONT WIPER MOTOR
RM27L0U _59 Vehicle Exterior _049351 WIPER / WASHER _0235978 FRONT WIPER MOTOR G

WIPER / WASHER  FRONT WIPER MOTOR  INSPECTION  


PROCEDURE

Hide 85110 1.INSPECT WINDSHIELD WIPER MOTOR ASSEMBLY

a.
E145558E06
2.574,1.932 2.749,2.114 0.175,0.181 10 +1 2.094,2.895 2.269,3.076 0.175,0.181 10 +2 1.036,2.925 1.192,3.107 0.156,0.181 10 E 0.135,0.105 2.755,0.740 2.620,0.635 10 Component without harness connected: (Front Wiper Motor) 1.379,1.623 1.447,1.65 0.068,0.027 1.853,1.629 1.92,1.658 0.067,0.029 2.034,2.022 2.523,2.022 false 1.885,2.455 2.163,2.885 false 1.42,2.455 1.134,2.89 false

Check the LO operation.

i.

Connect the positive (+) battery lead to terminal 1 (+1) of the connector and the negative (-) battery lead to terminal 5 (E), and check that the motor operates at low speed (LO).

OK:

Motor operates at low speed (LO).


If the result is not as specified, replace the motor assembly.



b.

Check the HI operation.

i.

Connect the positive (+) battery lead to terminal 4 (+2) of the connector and the negative (-) battery lead to terminal 5 (E), and check that the motor operates at high speed (HI).

OK:

Motor operates at high speed (HI).


If the result is not as specified, replace the motor assembly.



c.
U153983E02
2.313,1.417 1.521,2.146 false 1.698,3.781 2.104,3.5 false 1.938,3.844 2.292,3.844 false 1.042,3.844 1.396,3.844 false 1.51,4.115 1.177,4.427 false 1.875,0.313 3.021,0.75 1.146,0.438 10 false Direction of Motor Rotation 0.698,2.167 2.198,2.375 1.5,0.208 10 false Automatic Stop Position 2.729,1.115 3.104,1.323 0.375,0.208 10 false +3° 2.76,1.26 3.188,1.49 0.427,0.229 10 false -4° 2.406,1.198 2.792,1.396 0.385,0.198 10 false 17.6° 0.188,2.719 2.75,3.188 2.563,0.469 10 false Component without harness connected: (Front Wiper Motor) 2.135,3.385 2.25,3.531 0.115,0.146 10 false B 2.344,3.771 2.521,3.948 0.177,0.177 10 false +1 0.844,3.75 1.115,3.896 0.271,0.146 10 false +S 1.031,4.365 1.188,4.542 0.156,0.177 10 false E

Check the automatic stop operation.

i.

Connect the positive (+) battery lead to terminal 1 (+1) of the connector and the negative (-) battery lead to terminal 5 (E). With the motor operating at low speed (LO), disconnect terminal 1 (+1) to stop the wiper motor operation at any position other than the automatic stop position.


ii.

Connect terminals 3 (+S) and 1 (+1). Then connect the positive (+) battery lead to terminal 2 (B) of the connector to restart the motor operation at low speed (LO).


iii.

Check that the motor stops automatically at the automatic stop position.

OK:

Automatically stops.


If the result is not as specified, replace the motor assembly.